ROCK ISLAND TM22 UPGRADES

Rick Island TM22 upgrades
Riton scope
Holosun optic
Adjustable buttstock
Bipod
Compensator

[@ronniethompson3498]

Cool thanks for the heads up on the screw

[@Van020280]

All the Deyra TM22 models shipped to Canada are AR compatible and have 28-1/2 standard threading.

[@jamescuenca971]

Hi there! Could you tell me the thread size? Tried 1/2X28 doesn’t seem to fit.

[@jasonburgos5107]

So lucky i found this video, only 2 mins into it. I was trying to remove the stock off of mine and since i had hard time finding videos on the rifle and i looked at the manual and it just said to take the nut off and remove the stock i ended up being a dumbass and was like "this thing is toght let me use the wrench" and ended up scratching up the stock after 20 minutes of owning it🤦🏽‍♂️🤣

[@tiino4690]

Hey can you link all your modifications

[@dfines64]

What bipod did you use?

[@angelomarguglio1163]

Where you able to squeeze the 45 degree mount under the scope using Mlok? Hard to tell if you used a pic mount or not. Thank you.

[@opsman0848]

How did you polish the receiver

[@WreckLoose193]

Dope vid. What size scope rings did you get? My one inch rings won’t fit around the rail

[@sclegalcarry7979]

Your rings must be the same size as your tube on your scope.

[@rickkrystof6038]

As of today, 03/12/23 they are still allowing the mis-threaded ones into circulation. When I contacted Armscor, they said I'd have to return the TM22, BUT at my FFl expense, so I'd have to pay FFl fees for sending it back and to receive it back and where I am that would total $80 out of my pocket. I suggested they send me a properly threaded barrel and I'd return the incorrect one, and that way no need for a FFL as the barrel alone is NOT a firearm, but they refused saying a "gunsmith had to change out the barrel" even though their own owners manual shows you how easy it is to unscrew it and screw it back in, no gunsmith needed. So if anyone is going to buy a TM22, be sure to VERIFY it has the correct 1/2 x 28 threading BEFORE you buy and pay for it.

[@jmichna1]

An FFL is not needed If you are the owner and already in possession of the firearm. You can ship it directly to the manufacturer, and they can ship it back directly to you, as the owner. There is no need for an FFL to get involved. I've shipped both handguns and long guns to manufacturers for warranty work, and they shipped them back directly to me. As to shipping, there are restrictions on how you can ship; hand guns can be shipped between customer and manufacturer via FedEx, also long guns; long guns can also be shipped via USPS. You used to be able to ship firearms via UPS, but not sure if UPS still does that... they had serious issues with firearms theft during shipping, and resultant liabilities. Always check with the carriers for the latest info/restrictions.

[@Maurice3774]

Can you use these parts on the feather

[@rondean3775]

Heelo SC: Have you figured out if the tm22 takes milspec or commercial buffer tube?

[@TheHounddog2343]

What is the name of the bi-pod that you added?

[@outdoorman7425]

Does anyone know if a QD ring plate can be installed on the stock tube? I want to install a QD plate that has the ring so I can use as rear attachment point for a sling. I want to keep everything stock including the tube with butt plate. Thanks

[@michaelhartzell9758]

I have the Featherlite and the gun IS great, but i think the older model is SO MUCH MORE ATTRACTIVE!

[@nelsonm5032]

kind of a neat little 22. is swapping out the hanguard with a longer one an option?

[@AfroAngler93]

Yes you can I just bought one

[@ethanbadayos2170]

What handguard did you use?

[@MrDeath]

@@ethanbadayos2170 Did you find out?

[@JoeSmith-fu9yx]

It’s a commercial buffer tube that’s why it won’t fit, it’s a hair bigger than Mil spec.

[@Elmojomo]

The company says it fits "commercial buffer tubes". Seems like poor ad copy. Maybe they meant mil-spec buffer tubes? lol

[@paulsteinburg6449]

What is the actual brand of the side mounted holographic?

[@dakotacoats5004]

What buffer tube did you use

[@alexiscorral5991]

Where you bought the bump stock from?

[@ximhuh9653]

When you took off the buffer tube that came on the tm22 did you keep the stock spring or switched it to the new buffer tube spring??

[@sswaim13]

Pretty sure the TM22 is a blowback and doesn't have a buffer spring at all...

[@sirtango1]

@@sswaim13you are correct sir! 👍

[@Theoutofdoorsman]

Hey ! Where did you purchase the muzzle break I have been trying to track one down with no luck

[@sclegalcarry7979]

Dead air. From their website

[@sirtango1]

@@sclegalcarry7979did you Mask it? I have a DA Mask and a Banish 22 that I want to try on mine. Just got my TM22. I’m going to use direct thread though. Good looking setup! 👍

[@victoday01]

What brand and model is that adjustable stock?

[@sclegalcarry7979]

Amazon 32.99 Bosam Outdoor Sports Modification Accessories Polymer Adjustable Fixed Stock Outdoor Tool    

[@nicholaspugh5691]

What spec is the buffer tube? Mil or commercial? Wondering if I need to buy a mil spec or commercial tube

[@jorgeflores7081]

I believe it’s commercial not a standard mil spec

[@TheHolesmasher]

Its very easy to make either work

[@esgeso77]

how far can this rifle shoot 22 LR ammo...? did you do practical test..? thanks

[@USMC-Sniper-0137]

I did a search on You Tube and found that a .22LR round can travel 500 yards and still pierce a 3/8" sheet of plywood!

[@dustinpribble1546]

The reason u had to rig the buffer tube is bcuz there isn't a "standard" buffer tube, there's mil spec and commercial, the majority of ARs take mil spec. This takes a commercial buffer tube with is different than most on the market. I don't remember which is which but 1 type is a little bigger than the other.... not much but enough that it doesn't fit right. U have obviously used a mil spec

[@MarkChaney]

Arent the threads a bit different? Will a milspec tube screw in properly to the receiver? The threads seem a bit wider on the commercial tube.

[@dustinpribble1546]

@MarkChaney the diameter of the tube is different.... which yes impacts how it threads. I don't remember which is the wider 1. But yes it wint go together right, irll be loose. Technically u can use some thread tape or something but I would only do that in absolute emergency bcuz it might impact reliability and might actually tare itself apart through rough wear

[@MarkChaney]

@@dustinpribble1546 ugh, just wasted money on a stock/buffer that is on the way that ordered for it. I really dont get why they went with so many uncommon things on this rifle. Didnt make it any cheaper for them to build.

[@MarkChaney]

@@dustinpribble1546 Also, is the Derya TM22 different and the RIA one even though Derya makes the RIA one? Im seeing a lot of posts about people replacing it with a milspec tube

[@AfroAngler93]

Do I need to change the tube to add a stock or can I just add a stock

[@bosshog7790]

Not too sure. But if you buy a commercial buffer tube, you will have way more options on the stock. You would be able to buy adjustable stock. The tube that comes with the TM-22 had no holes for the adjustable stock to "lock" into.

[@landongara837]

Can anyone tell me if I need a whole buffer tube kit or just a buffer tube ?

[@bosshog7790]

Just the buffer tube and nut. I think it is a commercial buffer tube, NOT a mil-spec. You don't need the spring and buffer weight. They do not have a purpose on this 22 LR rifle.

[@AfroAngler93]

Did you put a spring in the tube

[@landongara837]

Did you put a spring in yours?

[@Mata65]

Wow

[@chickenmandave9756]

Exactly what buffer tube and stock did you use?

[@sclegalcarry7979]

Basic buffer tube. Nothing special about it. I had it left over from another build. The stock I got on Amazon.

[@landongara837]

Hey did you have to get a whole buffer tube kit or just the buffer tube itself ?

[@robertsmock5044]

Why a muzzle break on a 22? Please explain reasoning.

[@TheHolesmasher]

Looks cool

[@robertsmock5044]

@@TheHolesmasher I can dig it.

[@caseymelick8023]

When you ain't got nothing else to do

[@otunca]

Are these rifle-compatible with Ruger mags?

[@chasenichole813]

No, they are proprietary. Buy them from RIA or Advanced Tactical.

[@martinrps13]

Heard it is not 1/2x28…..sucks

[@sclegalcarry7979]

It's not. Buy they are changing it. Rock Island called me and asked me to return the rifle. I did. There is an issue they are working on.

[@martinrps13]

@@sclegalcarry7979 that sucks….but good to have them fix it

[@FitFarrier]

@@sclegalcarry7979 what was the thread on the one you had?

[@sclegalcarry7979]

@@FitFarrier I called and they told me it was metric by mistake. They did not say what metric it was.

[@drewmunny]

@@sclegalcarry7979 did they give you any indication of the release date? (re-release date maybe?) I'd sure like to grab one