Rockrider E-ST 900 Speed Unlock

Hello there!
In this video I want to show you how to increase the max speed of your Rockrider E-ST 900! The hack is the same on the E-ST 520.
You can try on other brands, if the components are the same as this bike.
Remember than you cannot use your bike on public roads and area after this kind of modification.
Use them only in private areas!
I'll not be responsable of unproper use of this modification

[@tamasmagyar6792]

Test Rockrider E-ST 500 from 2023 Thank you for your modification I tried. So you can do 450-500 pedals cycle and then the motor goes off without say anything. You have to turn off the computer and then back on. But I did 7km and the engine went off 2 times. The max speed on the flat road 41km/h but the engine still going so you can go faster. But your battery life on mode 1 took 10% in 7km. Normally I can do 100km range on mode 1, also 65km in mode 2, and 50km in mode 3 on a flat road with AVG speed 22km/h without the hack. So what this video explain is good but your engine going off when you ride more than 3km range. I hope you guys this review helpful and you can go realy fast in mode 1 with this modification but you know the result. So I do it back for factory result because I am happy with the 100km of range. Peace and love. 😊

[@beelikehoney]

luckily you own that whole road ;P

[@pasqualeagnello3341]

Yes, It was temporary closed to the traffic 😁 Support me suscribing to my Channel 😀

[@legorclfactory611]

I thought about the same 🤨😂😂😂😂

[@albertobisceglia7668]

what is the type of torks?

[@wackitywack]

Thanks to Pasquale! It worked for me. Now I can go 33% faster. My magnet is 15mm x 1mm (North). I used 4x cable ties and some double-sided tape as well. I was a little concerned that the magnet and the sensor were not exactly lining up, but I got them as close as I could. And hey, it works. I'm carrying spare magnets around with me in case something knocks my magnet off. So happy!

[@pasqualeagnello3341]

You are welcome 😊 Thanks to the support You gave me to increase my Channel 😃😃

[@paul59610]

Hey Paul ! 15mm x 1mm is a good dimension for the magnet ??

[@andrewbertram4116]

Hi buddy looking at getting the e-st900 what's the battery like buddy range wise cheers

[@mihaialex5668]

Size magnet? Link?

[@lfc-crowder3231]

anyone know how to do this on a rockrider est100

[@pasqualeagnello3341]

You cannot do this on that model 🥲

[@makeyoutubegreatagaintv4328]

With 1 hand driving so fast 😂🤦‍♂️🤦‍♂️

[@chrisnumnuts8671]

when i increased the max speed i just messed with the programing and got around 25 miles a hour. but burnt the motor out on 1 bike .and the mid drive motor i broke are someone broke my crank arm on the motor that was connected to the entire motor no way of fixing :( waiting for the battery technology to get better then maybe a new ebike for me .like this 1 in the video

[@Alitotheg]

Not all heroes wear capes

[@JobjeGames]

Is there a chance that a new rockrider e st900 detects the speedhack? I have seen some people say that it shuts itself off.

[@JobjeGames]

My new rockrider est 900 does detect the hack after about 5 to 10 minutes but if you restart it is ok again so i dont mind that i have to turn it off and on sometimes.

[@luisleon3795]

500 pedaling, no matter of time

[@matteopersico7542]

Ciao…per caso sapresti un metodo per rimuovere blocco velocita ad una rockrider e-st 100?

[@pasqualeagnello3341]

Ciao! Sulla e-st100 non conosco altri metodi se non quello classico in cui aggiungi la centralina che modifica la velocità rilevata...

[@deanbrady5240]

What controller unit do I ad for the est100

[@zaidakraa3185]

Can it be done with the est 100?

[@pasqualeagnello3341]

No 😟

[@jonathanelliot-yv1yt]

How old is your bike the new rockriders from Decathlon you can’t do this it has a restriction box now. O magnets

[@Muzzaa]

Is there another way to do it on the new bikes?

[@jonathanelliot-yv1yt]

@@Muzzaa I don’t know

[@degenetron7590]

46 ahahahaha holy cow, you need a 50cc motor driving license here in Belgium to go with those speeds

[@daniellacko6620]

to do the nutty thing bro

[@vitodr]

You are my hero 🤘

[@Xapiro]

Bonita, o mercado brazuca está começando a melhorar... Pena que não fizeram XL.

[@francescos6101]

ciao..ho appena comprato una 540E e chiaramente appena arriva guardo se fattibile. Avresti voglia di spiegarmi in parole povere il principio ? Cioè...il sensore , da originale , cosa legge ? e spostando perchè il contakm vede meno velocità del reale ? beh...nel caso ringrazio anticipatamente...

[@pasqualeagnello3341]

Ciao! Non conosco il modello da te citato, ma posso comunque spiegarti il principio di questa modifica: Il sensore di velocità che vedi nel video, non fa altro che calcolare appunto la velocità basandosi sul numero di giri che la ruota compie, ad esempio, in un minuto. Spostando il sensore verso il pedale (con il relativo magnete installato), esso rileva un numero di giri più basso, di conseguenza registra una velocità minore e non interrompe l'assistenza :)

[@irfanhendrawan9609]

The speed in GPS showed 47km/h but in speedometer was 15 km per hour, so the motor still gave power until it reached 25 km per hour in speedometer.

[@pasqualeagnello3341]

Exactly :)

[@degenetron7590]

wow

[@emericperez9244]

Tu as un rapport de 3,1 c'est normal 34 dents pour le plateau / 11 ça fait 3,1 et 3,1 x 15 = 47km/h il faut calculer le rapport pour chaque vitesse c'est pénible, mais bon au moins pas besoin d'acheter un kit de débridage à plus de 100€.

[@INSIGHTSAU]

Great video. Thank you, worked perfectly. I know the speed and distance won’t work after the modification but will the battery remaining and distance remaining still be reliable?

[@pasqualeagnello3341]

No, you'll have the same problem on the remaining distance. Instead, no problem on battery remaining

[@moj4477]

Nice :) It also should works with e-ST 100 model..?

[@pasqualeagnello3341]

No, so sorry

[@officekundig2018]

I did what you showed on the video and it is working fine. Speed increases till 42km/h. However the motor stops after a while and i need to reset the system. How can i avoid / solve this issue? Kind regards, jan

[@luisleon3795]

500 pedaling, no more.

[@officekundig2018]

@@luisleon3795 hi, what does this 500 mean? I noticed the motor stops anyway independly the speed after about 3km. After rebooting the motor starts again but again after 3km it stops again.

[@luisleon3795]

​​@@officekundig2018 forguive my english, i am Spanish... I mean that the bike reports the error when you turn 500 times pedals,, no matter time speed nor distance.

[@officekundig2018]

@@luisleon3795 Ok thanks for the explanation. However is there a way (solution) to bypass this irritating and annoying problem. PS) your English is fine -;)

[@luisleon3795]

​@@officekundig2018 i do not know any, but i do not stop the bike.

[@pietrosvelto1434]

Già fatto due anni fa e rifattora : funziona

[@futsumgebretensae5409]

Hello there please tell me how long last battery I need to buy this bike I work delivery so please and I will subscribe 😊

[@pasqualeagnello3341]

The battery is quite good. You can ride for 60-100km with a single charge. If you apply the hack in this video, you can go faster but you can ride for 20-30km with a single charge... 😀

[@abdihashi1649]

hey can you do one for the rockride est 100 please theres no unplug wire on the back wheel

[@AFOLTHEKID]

Have you found a way?

[@Wilson637]

Ty works man got 22 mph can proba get more with pumping up my tyres more

[@LVCMTB]

bel video !

[@regisalain3377]

Ça marche pas ça mer erreur

[@XxTheJackass58xX]

Scusa la batteria quanto dura con questa modifica?

[@pasqualeagnello3341]

Intendi come autonomia? 20~30km

[@KettlebellGunsmith]

Thumbs up. Still, this should be a photo or a 30 second clip. Not 5 min.

[@pasqualeagnello3341]

I accept this suggestment for the future :) Support me suscribing to my Channel 😀

[@poldecrossmol7160]

Does this trick affect the lifespan of the battery? Thanks for the help

[@pasqualeagnello3341]

Maybe on the long term...

[@glennshrieves7234]

I just did this today and it worked a treat, perfect mate thanks

[@dontreadmyprofilepicture5472]

Dont you have any error? Some people have said that it wil detect it and im nervous to try

[@andrewthomas7091]

Have you got the newer model ?

[@luisleon3795]

​@@dontreadmyprofilepicture5472 you have to reset every 500 cycles, no stopping the bike

[@AFOLTHEKID]

I have the newer model and you cant do this. Have you found a way?

[@starrider6777]

Hello, can you give me the references of your stand, please? Thanks a lot Sincerely

[@pasqualeagnello3341]

Btwin stand 500 😄

[@James-rx6fy]

Can you do it to the rockrider es 100 ebike

[@pasqualeagnello3341]

No, so sorry 😅

[@hodgsonnn]

Would this work on the est100

[@pasqualeagnello3341]

No, so sorry 😅

[@rickyfitsgerald577]

Ciao Pasquale A cosa serve il magnete? La dimensione dello stesso cambiano qualcosa in fatto di velocità?

[@pasqualeagnello3341]

Ciao Il magnete serve perché va a sostituire quello originale fissato sui raggi della ruota; senza di quello, il sensore non rileva alcun movimento. La dimensione dello stesso non influenza la velocità

[@rickyfitsgerald577]

@@pasqualeagnello3341 perfetto grazie Ho un’altra domanda, se la scatola del movimento centrale se misura 65mm non c’è possibilità di montare il bafang?

[@giuliasantucci4555]

Thanks for the video . I have done it on my new est 900 and it works! In eco mode goes easy to 35km/h , in Standard to 40 km/h . The problem is that with new latest est 990 model , with new Brose lcd control screen , happens that after about 500 pedal turns the power assistance off. Is like the system knows that the speed sensor has been moved . To have the power back I need to off the control screen and on it again. It seems that only the new 900 est model have this problem

[@milcus89]

Have anyone been able to solve this issue? It's really annoying when going up the hill...

[@luisleon3795]

No hay forma de solucionar eso.

[@dmitrypetukhov8391]

Not sure if its 500 rotations in a row or what. I had to switch on/off about 20 times for 60km trip today.

[@javierarreola5790]

Do you recommend buying this bike, is it worth it?

[@pasqualeagnello3341]

Yes, of course!

[@emericperez9244]

Par contre vous pouvez tous mettre un plateau à l'avant jusqu'à 42 dents mais moi je vais en mettre un de 40 parce que avec un 42t ça passe à 1mm du cadre, je trouve ça trop chaud personnellement. Et avec un 40t on peut se mettre sur la 9 ème vitesse et aller à la même vitesse que sur la dernière vitesse avec l'ancien plateau de 34 dents. Sauf qu'on pédalera moins vite et qu'on aura un peu plus de couple. Mais l'idéal serait d'avoir au moins un 44t pour aller vite. Parce qu'au final plus on va vers une petite vitesse plus on perd de couple moteur Vive les moteurs de vtt plus puissants et avec deux plateau ça serait génial... Il disent tous que les moteurs à roue arrière sont nuls, mais mon cul oui, les moteurs pédaliers font plus de 250W en réalité, je me demande même comment ils passent l'homologation, faut pas prendre les gens pour des cons sur le site de Bosch on peut pas avoir un active line et un perf line cx avec 40N.m et 85N.m pour la même puissance, avec la formule P = C x oméga on est obligé d'augmenter la puissance. J'ai vu que le Bosch fait 600W en continu en mode turbo. En réalité les moteurs pédaliers sont même moins bien à puissance égale. Sur le site de Specialized, 240W pour 35N.m alors que E ST 500 sur décathlon, moteur roue 250W 42N.m parce que les moteurs pédalier mangent de la puissance de par les engrenages de réduction de la vitesse à l'intérieur.

[@ultrainst1ct403]

Slt et merci pour tes explications, je sais que c'est un peu hors contexte mais est ce que tu penses que la technique qu'il montre dans la vidéo marcherait aussi sur un est 500?

[@notsureaboutthehandle]

can this be done on the rockrider e-st 100

[@pasqualeagnello3341]

no 😅

[@armandgromier7851]

Bonjour, après avoir mis en place et après essai le résultat est positif pour une utilisation sur du plat et pour une vitesse supérieur à 26 Km/h sinon il faut pédaler comme un sprinter et le pignon arrière n'est pas assez petit, ou celui devant assez grand pour prendre de la vitesse, ( car on mouline) c'est vrai il y a toujours de l'assistance, le point négatif est que si on ne pédale pas il n'y a pas de vitesse inscrite et pas d'enregistrement des distances parcourues, la vitesse sur le compteur est proportionnelle au pignon que l'on utilise, en pédalant ... pour ma part j'ai remis comme c’était d'origine, le montage est vite réalisable si je dois faire beaucoup de plat !! mais pas trop dans mon cas..

[@redy5734]

bonjour Armand Gromier j ai reservé mon velo pour la smn prochaine..cette modif m interesse pour aller au boulot mais je crains que cela crée des dommages pour le.moteur! il parait qu il y a une vitesse 4 bosst? elle est efficace? cordialement

[@pasqualeagnello3341]

Subscribe to my KZbin Channel 😊

[@ataksnajpera]

By the way. Imagine if you had 42T in front instead of default 34T. You could easily reach 50 km/h without that crazy RPM on pedals.

[@pasqualeagnello3341]

yes of course 😊

[@emericperez9244]

I think it's not a good idea, because the motor is not powerful enough, there is about 350w regardless of your gear ratio you will have the problem of the wind, if I'm wrong make a youtube video and watch that you are going at 55km / h on the flat. in addition in the big climbs have a 42 teeth for a chainring you will not be able to climb the hill

[@ataksnajpera]

@@emericperez9244 Dude! You have 42t in the back casette! 1:1 ratio with assistance is more than enough for climbing! Personally I hit 48km/h on regular MTB with 42t-11t on flat during calm hot weather ( no wind and 33C temp ).

[@str915]

If you install a 38t you can keep the original chain guide, and you can use the original chain, it's still long enough.

[@ataksnajpera]

@@str915 I'm planning to do that once I buy my Est 520

[@alkank9004]

Does this work on the newer versions of the est900?

[@pasqualeagnello3341]

Yes of course 😀

[@iwoo63]

Which kickstand fits the e st900

[@pasqualeagnello3341]

I don't remember the model... In decathlon you can find it 'cause it's an universal stand for Rockrider bikes

[@thomasbirch804]

Does this work on the EST 100?

[@pasqualeagnello3341]

No, so sorry

[@carolinagenovese8168]

Is it possible to modify the electric motor?

[@pasqualeagnello3341]

Don't think so...

[@КакОнинадоели]

Brauche Ladegerät fur mein Rad originale wurde geklaut..😢

[@thekerryman]

and now to find out how to do it on the new 2023 Rockrider E-EXPL range 😊

[@TIXIL]

thanks tested with E-ST 500 works perfectly

[@luisleon3795]

Does it report the error?

[@massimopalmiero5962]

pasquale spero tu legga e mi rispondi. modifica fatta ma sistematicamente dopo 2/ 2.5 km il motore si spegne anche sotto i 25 km/h . spengo, riaccendo e rifunziona ma non credo facciano bene al motore questo continuo " problema". hai una spiegazione e o rimedio? geazie un anticipo

[@pasqualeagnello3341]

Si, a quanto pare più di un utente ha segnalato questo problema (personalmente non pervenuto perché con modifica applicata non ho mai fatto più di 5km). Potrebbe essere causato da un sistema di protezione del motore che agisce per evitarne il surriscaldamento 😀

[@massimopalmiero5962]

grazie della risposta. io faccio escursioni di tante ore , penso mi convenga tornare all originale, che ne pensi!

[@pasqualeagnello3341]

Anche io ti consiglio di ritornare al l'impostazione originale. Ti godi meglio ogni pedalata (oltre che preservare la bici) 😀

[@luisleon3795]

No es problema distancia ni tiempo, son 500 pedaladas

[@mahadonsax]

Hi, I have done this hack to my rockrider E ST 520, but sometimes I find that the motor cuts out so I have to power of the display and power on again and then it works ok again has anyone experienced the same problem?

[@pasqualeagnello3341]

Try to move a little bit the sensor on the chassis :)

[@mahadonsax]

@@pasqualeagnello3341 I will try that, I also thought about putting another magnet next to the other one to give it a wider contact, have you still got your est 900 and if so, is it a good bike?

[@pasqualeagnello3341]

Yes... It is a very good bike!! 😁

[@ultrainst1ct403]

@@mahadonsax any updates on your est 520?

[@mahadonsax]

@@pasqualeagnello3341 Hi, no I still have the same problem, I tried moving the sensor but it still cuts out after about 5km!

[@prabhusiva1940]

Can this damage the motor or any other sensor ?

[@pasqualeagnello3341]

No, but you could overheat the motor... 😅

[@sandrosella2371]

Avrei una domanda!!! Hai solo tolto il sensore perché non lo veda il ferro sui raggi della ruota, o anche altro??? Grazie👏

[@pasqualeagnello3341]

Si esatto, ho solo spostato il sensore e messo un magnete al neodimio dietro al pedale, nulla di più 😃

[@sandrosella2371]

Facendo così che velocità sei riuscito a raggiungere con la bici!!!

[@pasqualeagnello3341]

Esattamente quella che vedi nel video 😃

[@PawanSharma-n3o2s]

I have same bike where I buy this sensor you putt in the pedal where I buy

[@alejandrog553]

Could be put two sensor, one in each position ( near crank with magnet, and another legal) and between this a switch.

[@pasqualeagnello3341]

Don't know, but you can try 😀

[@ataksnajpera]

Very elegant hack! Much better than buying overpriced speedbox and then cutting wires! Thank you! I'm going to use this hack in 520.

[@pasqualeagnello3341]

Thank you ☺️ You are right... I used this hack 'cause I had to purchase only the Neodimium magnet... The hack in which you have to buy the speedbox is quite expensive. I obtained the same result 😊

[@antwright9228]

Did you use this on your est520 ?? If yes what speeds did you achieve?

[@pasqualeagnello3341]

It works also on the 520 :)

[@crucius]

@@pasqualeagnello3341 Do you think it would work on the Riverside 500e? And what does the magnet do? Would just removing the plug not be enough? (the Riverside has the speed sensor on the actual pedals)

[@pasqualeagnello3341]

Hmmm in that case I don't think you'll have the same result :/ but you can try and verify :)

[@bradmaxwell1143]

i bought some of the magnets but they are not with adhesive pads, which way around does the magnet need to be should it attract or repel from sensor?

[@pasqualeagnello3341]

It needs to be repelled from the sensor

[@szpity2258]

hi, do you know how to tune this Riverside 500e?

[@pasqualeagnello3341]

You have to check if the speed sensor I moved on my bike is more or less the same on the riverside :) Support me suscribing to my KZbin Channel 😊

[@maximeleturgie4332]

Hello szpity Have you tried on your 500e ? Did you succed ? Thank you

[@pasqualeagnello3341]

Hello there 😀 Please support me and Subscribe to my KZbin Channel 😊

[@Jay0227_]

I did this with my est 520 it doesnt display my speed anymore and says error but it does go fast for like 20 seconds and then it slows down because it says error. But i didnt have a magnet so is that the cause for the error?

[@armandodebenedetis7214]

Ciao con una carica completa quanti kilometri riesci a fare con questo hack

[@pasqualeagnello3341]

Ciao! Purtroppo, dato che con questa modifica, l'assistenza praticamente non si disattiva mai, l'autonomia scende a meno di 30km....

[@ciervo_equix]

Nice video! Are you happy with the bike? Any problem?

[@pasqualeagnello3341]

Yes of course! No problem detected with this bike, it's only a little bit heavy but it's normal on an e-bike 🤣

[@TheKerrby]

Doesnthis work for the est-100 too?

[@pasqualeagnello3341]

No, so sorry

[@TheKerrby]

@@pasqualeagnello3341 thank you for the reply. Do you know of any Jack for this bikes motor?

[@lama-kc1sb]

Does it work on my e st 100 too?

[@AFOLTHEKID]

Can't do it on mine as they have changed the sensor and its now on the crank. If anyone has any idea how to do it on a newer est100 please let me know

[@HarveyEveson]

@lama-kc1sb did you find out if you can do it to your e st 100?

[@noelbolandmusic]

Hi Just got my e-st900 and found the 25km restriction really annoying on dirt trails. If I do the hack you suggested which is brilliant BTW if sticking to around 30-32kmph would the battery drain much quicker in setting 2. Thanks

[@pasqualeagnello3341]

Yes, of course the only big problem is the battery drain increased after this hack 😥

[@nealthomas9677]

where can i buy the magnet please?

[@pasqualeagnello3341]

You can find them on amazon as "neodimium adhesive magnet" 😃

[@nealthomas9677]

@@pasqualeagnello3341 i did this today wow.. thanks its much better now,,

[@pasqualeagnello3341]

You are welcome 😊

[@dragosburcan6721]

I changed the speed limit but the motor it stopped and it didn't started again. I went to the repair shop and they fix it. I take it off again the sensor I switched of and on again and I could ride it with the maximum speeds and it is a beast. Now every time when I m taking off the sensor it showing: Error, Check the Speed Limit. Can you tell me what should I do?

[@gabonalumi]

Ciao, si può fare su tutte le bici elettriche delle Decathlon?

[@pasqualeagnello3341]

Ciao! Non saprei... Sulla e st520 e sulla e st900 sicuramente. Sulle altre dovresti verificare se le componenti indicate nel video son più o meno simili e collocate allo stesso modo.... Tieni conto che questo hack funziona spesso anche su ebike della concorrenza, per cui c'è una buona probabilità anche per le altre della Decathlon 😃

[@luisleon3795]

Es facil de hacer, funciona bien. Habría que averiguar porqué detecta el truco y da el error. ¿También lo da si vais variando de piñón? It is easy to do, works fine. Just have to guess why detect the change. Does it detect it if you are changing speeds? El error aparece cada 500 pedaladas, no hace falta parar la bici, reinicias y ya està

[@osak_iama7914]

i wanna do it but in what mode ur using?

[@pasqualeagnello3341]

The max power mode

[@osak_iama7914]

@@pasqualeagnello3341 thank you👍

[@louibmx]

Great but then u Lost Decathlon warrantee for thé engine ?

[@pasqualeagnello3341]

No, 'cause you can put all pieces in the original setting... And if you remove the extra magnet, no one can know about the previously hack :)

[@christostsarouchas5453]

Nice Video thx for this! Only one question witch Magnet i Need for this ? Size?

[@pasqualeagnello3341]

10mm diameter magnet :) Support me suscribing to my Channel 😀

[@christostsarouchas5453]

@@pasqualeagnello3341 thx Bro !

[@bekf9374]

What about RockRider St 100 ? Et merci

[@hanspeter3495]

Do you have any Problems after Tuning?

[@pasqualeagnello3341]

No 😀

[@hanspeter3495]

@@pasqualeagnello3341 And the Quaranty? Thank you For the Video.

[@pasqualeagnello3341]

No problem for the warranty. You can remove the hack anytime you need

[@SupremeStreetRacer]

Where did you buy the magnet? You have a link?

[@pasqualeagnello3341]

I haven't any link at the moment... On amazon, if you look for "neodymium adhesive magnet", you'll find it 😀

[@masonferguson4482]

does this work on the e-st 500v2?

[@pasqualeagnello3341]

You have to verify if the sensor is in the same position as the E-ST900 😁 Support me suscribing to my Channel 😀

[@TPHB5011]

Why are you putting a magnet there?

[@ziodylan5965]

Top 🔝

[@louibmx]

Just get thé bike from thé shop today. Gonna wait a little bit before hacking it

[@pasqualeagnello3341]

Good idea 😉

[@louibmx]

@@pasqualeagnello3341 thé bike is sold out everywhere in France 😮

[@pasqualeagnello3341]

@@louibmx also here in Italy 😥

[@jerzywoking1699]

Just got one in stock in my local branch in Spain, so i ordered it. Should be with me in the early part of May.

[@labuche62]

Transformation effectuée sans souci Reste à trouver un plateau plus petit Si quelqu’un a des références je suis preneur. Merci

[@novalux1447]

Hi Pasquale! Thanks, do you know if works the same for the new Rockrider E-EXPL 520

[@pasqualeagnello3341]

I don't think so. It doesn't run also on the last model of est900

[@kevinpinon2311]

Is there a need to put a single magnet or it is necessary to put 2?

[@pasqualeagnello3341]

Single Neodimium magnet 😃

[@WILDKAMERAD]

I have done it at a 2023 model. Worked for 6 km and then the motor bloked. Had to change it to the original setting.

[@Muzzaa]

Did you find another way?

[@WILDKAMERAD]

@@Muzzaa Yes, a perfect one. I use Bikespeed RS for Brose motors. Works flawlessly and even the speedometer and the data in the software are retained. You can also switch it off.

[@Muzzaa]

@WILDKAMERAD would you be able to tell me a bit more? Was it easy to fit? What top speed do you get now? Have you come across any issues since using it? Does the battery drain considerably faster? Thanks mate

[@unpopular_opinion1468]

what about est 100? it does not seem to contain the plug thing.

[@burakggh8625]

I’m having error it says check your speed sensor and it won’t work help me please

[@StayF0cused987]

If you have a newer bike like from 2022 or newer , it won’t work , they have special system installed to stop this I have a new est-500 v3 and doesn’t work

[@jaapprins5064]

Hello,is this also possible with the st 100?

[@pasqualeagnello3341]

No, so sorry 😅

[@jaapprins5064]

@@pasqualeagnello3341 thats a same🤣🤣

[@andrewthomas7091]

Does this work with newer models? Cheers

[@pasqualeagnello3341]

Yes, but only on bikes with the central motor 😁

[@andrewthomas7091]

@@pasqualeagnello3341 I have the newer type LCD screen computer

[@pasqualeagnello3341]

No problem. You can use the same stand :)

[@juancarlosrodriguez542]

Hello, hello! Interesting your video and very constructive ... I wanted to ask you if there is another alternative to these magnets.I mean to make you understand me, if they should be these magnets exactly (Measures-10MM / N42 or I can put other similar of the same brand ... I am Spanish and I looked at Amazon and these same do not appear, if they appear almost equal (10 MM / N35 O N50) to those in your video. If they are all the same as the ones in your video but they are black, with epoxy... would they fit me? Thank you very much and very kind!

[@pasqualeagnello3341]

I think you can use something similar, the sensor will detect it without any problem 😀

[@adriankowalik-345]

does it also work in the e-st 500 bike with a middle pedal?

[@pasqualeagnello3341]

On newer model it doesn't run

[@fabio47592]

Funziona ma c'é un problema....ogni 15 min. circa il motore smette di funzionare. Devo spegnerlo e riaccenderlo, ma ogni 15 min. fa così....come posso fare per risolvere; sai da cosa può dipendere? Grazie (da originale funziona perfettamente)

[@pasqualeagnello3341]

È dovuto al surriscaldamento del motore.... Non c'è rimedio purtroppo 😅

[@luisleon3795]

500 pedaling, no more

[@mystic-spirit]

It worked, thank you soooo much

[@JoaoSilva-dp3pe]

Does it work on these latest E-st 900s with the brose allround display?

[@pasqualeagnello3341]

Yes 😀

[@JoaoSilva-dp3pe]

@@pasqualeagnello3341 But is there a minimum time to run the engine? or it goes into safe mode? do the tour , sport, boost options still work?

[@pasqualeagnello3341]

It will start almost immediately... And it works in every modality :)

[@JobjeGames]

@@JoaoSilva-dp3pe i have one with a new display and it turns of

[@luisleon3795]

​@@JobjeGames but it works again after restart sistem?

[@mikescott29]

wil this mod damage the battery in any way?

[@pasqualeagnello3341]

No, but you have to charge it more frequently 😅

[@mikescott29]

@@pasqualeagnello3341 right...of course .ok thanks i love rockrider bikes .mine was stolen am thinking about getting this one

[@pasqualeagnello3341]

It's a very good choice

[@iamcRuNcHiE]

On my new e-st900 I can’t get the sensor screw undone! Wondering if they have glued it in. Not reverse thread is it?

[@reelBorsti1912]

Great Video...Thank you :-) It works well

[@PB22559]

What ebike did you do the hack on? The same model E-ST 900?

[@MrOrchin33]

I had the same problem with my st 520. Works great for a while and them cuts out and you have to rest the bikes controller. Any suggestion?

[@luisleon3795]

500 pedaladas

[@HareemUk]

Can i remove sensor so thay increase speed

[@pasqualeagnello3341]

No. It gives you error

[@Paolo21977]

:-D

[@frankreilly8071]

A bit late in the day perhaps but how exactly does it affect the odometer?

[@zenrac9182]

There's a magnet on the wheel that is used to calculate your real speed. After this modification, because you put a magnet on a pedal it now considers that your pedal speed is your wheel speed. It can't know what is the real speed because of that.

[@ablak3712]

what happens if you just remove the sensor without a magnet?

[@luisleon3795]

The bike gives an error

[@mariano7878]

This is very bad for the batery.

[@pasqualeagnello3341]

Yes, a lot...

[@pasqualeagnello3341]

Support me Subscribing to my Channel 😀

[@dontreadmyprofilepicture5472]

Do you mean bad that it can break or bad that you have to charge much more

[@mariano7878]

@@dontreadmyprofilepicture5472 high discharge is bad

[@dontreadmyprofilepicture5472]

@@mariano7878 ok thanks

[@kickdown7143]

Do you glue the magnet to the paddle or how do you put it to the pedal?

[@pasqualeagnello3341]

The magnet had an adhesive included... The procedure was immediate 😃

[@FlorinGroza-ey4mm]

Whit the e st 100 model it works ?

[@rad1bob412]

Hello , first of all a big thank you for your great video,I come back to you to ask you a question for a problem that I encountered after making the modification, when I drive for a few kilometers +/- 5km the engine stops the assistance, Every time I restart it so that I can continue, I hope you can help me find a solution in advance Many thanks

[@pasqualeagnello3341]

Hello there 😀 Probably, after this hack, the engine works harder than in the original setting, so it make a lot of energy and become hot... It turn off itself to protect all its electronical components :)

[@rad1bob412]

but I had already checked the engine it was not hot, after restarting it starts again normally without problem and immediately . Is there not another reason like the stability of sensor or its position or direction of magnet or the speed of rotation of the pedals because I have friends who do not have this problem really I am lost thank you For your help I asked a few technicians but still no solution 😔😔😔

[@ataksnajpera]

@@rad1bob412 Install stronger magnet

[@rad1bob412]

@@ataksnajpera thanks for ur answer i wil try and i come back with more details

[@zsoltruzsinszki8122]

@@rad1bob412 Same here