Roland SP 540v 300v PRINT HEAD replacement and ALIGNMENTS save money replace yourself! DX4 EPSON

[@ccerritos]

Mike thank you for sharing your knowledge, today I have replace my DX4 head print of a XC-540. A little fear at first but following your instructions I have done it with no complications. A little tricky enter the service menu, I have entered my head rank and notice the techie who replaced one head before have not entered the head rank so I entered it today. Just a final step I´m working on, head alignment but at firs impression everything is ok. I have to bought you a beer, you´re the man!

[@reprint217]

Thanks brother! Appreciate the support!

[@johnton5656]

This man is an asset to humanity. I was stumped - he patiently winched me out. Hats off sir, you are the absolute best! May you live a long and happy life.

[@reprint217]

Always a pleasure

[@CBrand-wg6mx]

Gosh your knowledge of this printer is endless. I am dealing with no yellow at all. So listening to you is priceless

[@reprint217]

If you get stumped, please don't hesitate to reach out.

[@iamthebeginner4446]

Thanks !!! Mike’s the best guys, make sure to always like and watch his videos 🇹🇹✅

[@reprint217]

Much appreciated bro!

[@mfield6328]

Hey Mike, just want to say thanks for the video, you helped me get my SP300v up and running after sitting for a few years. One question I have tho is: what would cause the printer to print perfectly at 15” but if if I print past that the images become misaligned? Thanks again for your videos! Keep it up 🤘🏻

[@reprint217]

Appreciate the feedback! Likely encoder strip or sensor

[@chadoelschlager1746]

great video,thanks for doing that and including how to adjust,wished could seen ya finish it out..but great video nonetheless

[@reprint217]

Did you get the 540i going?

[@chadoelschlager1746]

@@reprint217 soaking the heads and pulling vaccum w syringes just like in one ur videos,.I have put cleaner cartridges in each slot a d as if last night, I have solution pulling from black,blue,magenta, but not yellow.. ut the other 3 I see in on pretty easily through the lines

[@jameswei7003]

Mike, if the vertical is missing alignment slightly like your Magenta, you turn both the white knobs instead moving the print head physically

[@reprint217]

You can but mine the actual metal was stuck from age kinda welded itself in place

[@phototec]

Awesome video, best SP540V head replacement video on KZbin. I have a question, near the end of the video when you are doing the alignment tests, I see that you are entering 1/2 numbers, like 20 1/2, how do you enter the 1/2? the last time i made the adjustments, i was thinking you could only enter the full number like 20 or 21. Thanks again.

[@reprint217]

It has the half options in service menu. Allows for micro adjustments

[@phototec]

Yep, after I install my new M/Y head and was doing the alignment procedure, I found that is has 1/2 options between the full number options. Thanks for the reply. Another question, after installing the mew M/Y head I see ring of magenta around where the brown part sit on the meat frame, what could cause that? I don't see any on the B/C print head.

[@Stefano-en7jg]

Me again, anyone here have an idea for this? LEF-300 with CMYKPrGlW setup absolutely no gloss or white, but good primer output (so some of group B works). Pulled the mainboard, tested fuses and fets, all good. Replaced #4 printhead twice. Replaced carriage board, no change. New genuine captops, good suction, seems to pull ink during powerful cleaning on group B. All brand new ink. Flushed with cleaning cartridges. At this point theres not much to throw at it but ribbon cables (impossible to find) and a main board ($$$).

[@reprint217]

Oh man, it sounds like you are having too much fun. You're in one of the situations I hate to be in, especially on these LEF machines. Let me think of what I would do next. I would carefully remove all cables to insure I didn't create any new problems. Only keep 2 cables that are supposed to go in a color head and place in the white / gloss head. Do they fire now? If yes I can tell its something coming from the back, mainboard/carriage board. If it does not, that tells me head is the issue. But if it does fire. Take the head cables from the white/gloss and place in a known working color head. Does it fire? Just a process of elimination at this point.

[@judy-jo8vu]

hi there, your videos are extremely informative. i have a roland lef20, with the dx4 printheads. my gloss n white is completely gone after manual cleaning with the sponge n solvent. CMYK is perfectly fine though. i've been able to suck ink out from the captop, the white seems to be coming out while i dab the printhead with the sponge (the gloss i can't really see), but the head is just not firing (the heads are moving when i try to print, versa works ink status say it has plenty of ink, which i think its only at 1/3 ) any idea what could be the problem??? where i am isn't that easy to get help, and i've never changed a printhead before ( not just its delicate work and expensive, but i have to mail it over and do it myself, which is nerve wreaking) so i hope its something easy that i may have overlooked. thank you so much for the videos again

[@reprint217]

Could be a fuse

[@judy-jo8vu]

@@reprint217 thank you for the prompt reply. do u happen to have a video in how to replace it or fix it??

[@user-mt8ig4wl5l]

Hi, great video. I was able to change both heads on my SP-540i after watching this....however I have the same issue as you had, only the Black and Cyan head firing when doing a test print. I've replaced the printer carriage board but still the same. You mentioned a bad fuse or transistor on the main board which you fixed. Any pointers on how I can do that?

[@reprint217]

On the mainboard of a 540i there are fuses check them first. You can easily remove and swap them around and see if magenta yellow will fire. You will need to be in service mode or will get a temp to low error

[@jacobuspertrustheron-zh7yb]

Good day. I am new to the Roland printers,we have a old Sp300v. In the 6 months we have had the printer we have replaced a print head as well as the print head bearings. As we where getting scan motor errors. Ok the bearings was bad. But now we still get the scan motor error every now and then. But seems to alwys be at the same place. Previously it was at random intervals all over the printer. Should i replace the scan motor aswell?

[@reprint217]

Have you replaced encoder strip yet? If not would try that first. Typically I will do Emcoder strip/sensor, scan motor

[@Stefano-en7jg]

Hey! Thank you for the video. Replaced the 4th printhead on a LEF-300 as there is no ink from the white whatsoever. After 4 powerful cleanings still no white and none in the replaced damper. I can draw white out with syringe before the dampers. Any ideas? I'm thinking fuse but I can't find the service manual for this unit. Btw all the screws on these printers are JIS not Phillips so a nice JIS set like the sunflag on amazon will go a long way.

[@Stefano-en7jg]

Also, where can I buy genuine captops from? The ones from all-printheads were not genuine but had black hoses.

[@reprint217]

Ok, troubleshooting an Lef300 number one is that if it were a fuse you would be getting nothing from 2 heads. You have flow at the line but none to the damper. Did you replace the damper stay that holds down the damper? Sometimes they sit up high and draw air. I'd lean towards captop. Connect syringe to captop hose if its getting air, wiggle head carriage by hand see if can get good suction. For captops premier colour is my go to. Email me at [e-mail] I'll shoot you over service manual

[@cedomirburilo3796]

In the video at minute 13, you said that the motherboard has a problem with the transistor. I have the same problem, I installed both new heads, new original dupers and captops. How did you fix those transistors?

[@reprint217]

Soldier in new transistors just make sure they are the same. There are 2 variations on that board a PNP transistor and an NPN A1746 and C4131 make sure you replace with same model transistor.

[@strivn72]

Do have to go through the same process to change the manifold only?

[@reprint217]

Unfortunately, so, the only way to remove the manifold is by removing the head.

[@phototec]

When I print a nozzle test print I have NO yellow at all, what steps should I take to get the yellow to print? Thanks

[@reprint217]

Likely just need to replace the captop.if were me I would use syringe to draw ink. If problem keeps happening replace that captop

[@roaprintwrapsllc1090]

Hi Boss, I bought the same Roland Sp 540v to you like 3 yrs ago, I think that I need to replace the print head, can you help me with that, I already have two brand new original Printhead.

[@reprint217]

Yo, sorry was at trade show in Orlando all last week. Still need help

[@roaprintwrapsllc1090]

@@reprint217 YEEEEESSSS PLEASE

[@rafiqalam8418]

Thank you! But it would be nice if someone else hold the camera and perform the video recording! Its very difficult to see your action when you are moving, talking and working together!

[@reprint217]

Yeah unfortunately I make these videos myself on the fly to help others. Though it would be nice to find good help.

[@sadguruspiritual]

I am getting an error that says "wrong head". How to I match my head number to the printer service menu head number?

[@reprint217]

What printer do you have? Usually only see this error on VP Xc and Spi models using old white connector heads

[@reynaldoisaac6824]

Helo sir why my Roland rs 640 doesnot pump the ink but i already replace the two pump. Thanks alot sir. Gbu

[@reprint217]

Sounds like you may need to do a flushing adjust

[@Gvozden73]

So whats the story with that caps from digiprint? Someone say there ok, like oem, some1 curse them...

[@reprint217]

Anything aftermarket is hit and miss. Very inconsistent batches. They caused us more trouble than they were worth. Stopped using them couple of years ago. If you decide to try, don't give up and write the head off as bad!

[@wernerstrackx6073]

Hello, I have the same problem, after installing an unlocked print head this head don't print and I have the same test print as you. fuse's on mainboard are okay, what else can i check? it's on a sp-300v

[@reprint217]

Typically, if the fuses are good, the transistors are as well. Can he take head cables from good head and move them to the other head? If you bought the printhead used , it is likely the head 99% of the time

[@wernerstrackx6073]

@@reprint217 I've done it now. The same colours are printed. it is a Chinese unlocked head, this head is not good or could it be something else?

[@jessicarosales3512]

I need help my sp 540v is telling me pinchroll error invalid right pos and I cant figure it out

[@reprint217]

Replace your cut carriage cable