How to retrofit a M5 cluster on a E60 5 series BMW

[@vshopov89]

I have a manual 535xi and the cluster I got came from an smg... now if I code the kombi like you did will it automatically code it with the manual trans cause I got a trans malfunction because m5 was an smg

[@piduino]

What happens if you don't zero the milage and just fit a higher milage one? Will it save the highest to the DME permanently?

[@rikki920]

Hello and thank you so much for this easy to follow guide it very much appreciate. You mentioned calibration will you do a video on that or a link how to. Thank you for your time 👍

[@haykarthurtovmasyan6150]

Does the temperature gauge properly work too?

[@sehmuse36]

Can i retrofit that cluster on my manual 6 gear E60???

[@paulblackburn252]

Q. If I source cluster and swap at the same exact km odometer reading do you need the coding ? Other than assigning vin to module ?

[@buddiec41]

Love it thanks info on programmer and software would be nice and how to program milage and align needles after removal

[@roskinc]

Viddi programer I use for the vin, r270 programer for the mileage if you need to, and for the alignment program called PERFECKTOOL I’ll try film a video on these steps as well

[@buddiec41]

@@roskinc dude that is awsome I cant wait ...one other question I purchased a blue tooth module from you a while ago it's great however on some songs volume is really low and volume on phone and radio is maxed out is there some where in coding to offset the volume for aux if I go back to radio or CD or ipod it his fine I have to turn it down.....1 more I also coded in the high fi sound equalizer it shows up but is greyed out on adjustments can that be fixed per coding also thanks bro your hacks for the e60 are great

[@scarface16134]

The mph is wrong for me out of the box I can’t find a perfekt profile to be correct, do you have one?

[@bobbybuilds208]

How much to have you do this for me? Also, were you able to get the temp gauge to work? If so, how? Thanks and great video.

[@billgates7221]

Great video!!

[@halilerhanilgaz9758]

Hello roskinc. I want to change the leds of this Bmw E60 M5 instrument cluster to white. Is there a video about it? Which leds will be removed and replaced with white leds? Thank you very much.

[@eldin9117]

I have 07 e60 pre lci ... does m5 cluster has to be pre lci to work in my car or lci can be coded in ?

[@roskinc]

Yes correct, needs to be pre lci still. Didn’t mention this in video so i will pin this for people curious, didn’t think of it til now.

[@d.philliproberts1233]

roskinc whats your email?? i need a sport mode wire for my 06 525xi

[@thebestsoccer2063]

Hi did u know how use the perfekt tool box?

[@slavdesystem4594]

Hello. After retrofit cruise control won't work.. several different coding.. Still ssme .. Old dash works fine.. Any idea? E60 face lift 3.0i

[@cruzfernandez4554]

I would like to know if you have done the F10 6WB cluster swap

[@user-bq1ls8cf1p]

Plz answer Can you just move the chip from your Old cluster and move it to the m5 cluster?

[@radii2029]

No, you have to use the original chip but with changed VIN

[@robertsmanguss8680]

Great vid tutorial mare can you maybe do a retrofit video of From small idrive to big ccc or cic From semi auto seats to comfort sport (ventilated,massage,heated) seats,mby rear foldable heated seats too Heads up display retrofit from scratch Paddle shifter proggraming and retrofit These are some of the things i would love to retrofit on mine e60☺

[@clippa10]

If I buy one and send it to you can you program it if I pay you?

[@Entertainmentinc1]

lol so much extra work, when i changed my cluster i just flashed the cluster to my vin/car with winkfp and everthing was good to go, none of this bs soldering and messing with chips. you can also use softwares like bmw scanner 1.4 or ista

[@roskinc]

You probably bought a cluster that was virginized

[@Entertainmentinc1]

@@roskinc not sure but i know for a fact bmw scanner 1.4 can program non virginized clusters or any other module really

[@r.b1288]

Will the needles work properly? I mean will it go up to 200miles? I have 535d and I'm interested in this. My cluster is 160miles and 5x1000. Do you think it will work properly on mine? Thanks bro and thanks for the video

[@jianiversace9787]

Are e90 335i gauge cluster interchangeable with e60 535i

[@RodrigoCabralify]

goodnight! I speak from Brazil, I have a 530i e60 and the panel has a problem, but I have an x6m dashboard, it does not work with some functions, is there any coding to release this?

[@dron6833]

Hello, do you know what is missing in my e60 pre lci cluster , i dont have cruise control circle ? Can i add this part from other cluster or i must replace the cluster ? Thx

[@youtuner7012]

Can i do this to my 530d?

[@vico9252]

awesome tutorial thks man you dope

still alive !

[@DamnSword2007]

Hey! Thnaks for the vid but I have one question: Is it really necessary to configure the chip? Can I just jump to the second stage?

[@roskinc]

Yes otherwise you will get a tamper dot. The VIN have to match. If the miles on donor cluster is lower than current mileage then it will display the higher mileage (your car) if you put a higher mileage cluster on the vehicle, it will show the higher mileage.

[@Stefan_Smith]

Cant I switch the chips from 1 cluster to the other? instead of coding? I don't have your coding tools that you used.. what was that electronic device that you used? Can you list that and the programs?

[@Bemaritohtori]

So the VIN inside the eeprom is not possible to be changed via OBD? For example using tool 32 or winkfp?

[@roskinc]

Correct only be done via the method shown. Can’t be done obd2 with any software

[@Bemaritohtori]

@@roskinc thank you for quick answer. I was wondering if I should try swap the chip from the original into the donor. After that, just factory coding.

[@roskinc]

@@Bemaritohtori yes you can do that

[@alexbita5658]

@@BemaritohtoriI swapped the chip from original to donor and nothing works besides when driving only speed showing, no rpm or gas sensor showing anything

[@halffilms5975]

I just ordered a aux input from you’re site how long will it take to come ?

[@roskinc]

shipping out in the morning, should receive it by Tuesday since your not to far.

[@halffilms5975]

roskinc thanks bro appreciate it 👍

[@clippa10]

If I order a m5 cluster and send it to you could you program it if so tell me how much

[@mannylugo8103]

Hey man, anyway you could help me with a problem I’m having with my e60. Radio and idrive? I can’t seem to find anyone that knows anything about it.

[@manueltorres5698]

Do you sell clusters already programmed

[@jaymesalonzo8543]

Or can we send you clusters to program via mail and all we have to do is just install it after its shipped back to us??

[@ANDYW031084]

What about the mileage Can you Set the different mileage?

[@roskinc]

You can change the mileage if the mileage on cluster is HIGHER than your actual mileage in car. If you change the mileage lower it will still show the mileage that your car has.

[@ANDYW031084]

@@roskinc Thanks !!!

[@ThesteliFLo]

Are u still offering this service? I would like to get one from U ready PNP for My car!what is a good way to-get in touch with u? Thx u

[@roskinc]

Shoot me an email roskincdavid at gmail

[@thebestsoccer2063]

What i do if i dont have the machine for read the chip?

[@roskinc]

You can send me the cluster I can program it

[@rbriggins]

@@roskinc I'm interested in having a used kombi cluster programmed for my '05 545i. How do I get the used module to you? Thanks, and really enjoy the channel btw.

[@JAD-Kuku]

Hi I need to say that I am a very big fan of you thanks for all your videos it helped me out with my E60 my question is if you can help me out with my ncs expert it won’t really work in my laptop I tried a lot to make it work but it still doesn’t please try to contact with me.

[@roskinc]

What issues is it having?

[@JAD-Kuku]

@@roskinc when i try to connect my car it shows falt with reading the VIN I can't send you pic of this hier

[@JAD-Kuku]

COAPl-2000: fault in EDIABAS or in SG-Beschreibungsdate IFH.0018 lnitiatisierungs: feller des interface Handlers CAS

[@roskinc]

JAD Al Koko check the coding cable setting make sure the com port setting are correct

[@bengisusakarya9967]

helle thank you for your tutorial video since ı don't have a VIDI programmer ı solder an empty eprom to the boiler ı wanted to encode to default with ccs expert but coapi 2060 codierunggehlerhaft allgemein komb60 c c auftrag error ecu download not accepted coapi 2060 codierung fehlerhaft.

[@eardleyjohn]

Can I send you a cluster and vin and have it coded by you?

[@roskinc]

Yes

[@iwanwish78]

@@roskinc hi bro what write no in programmer ic.its kmh .

[@d.philliproberts1233]

whats your email @roskinc???

[@alcepedaconcepts]

How much to have you do this for me? email address?

[@roskinc]

[e-mail]

[@alcepedaconcepts]

@@roskinc send

[@mahdebmw6704]

Can't codeng