Rotary Tool Bits for Beginners: A Silversmithing Tutorial

Рет қаралды 2,055

Chad’s Silversmithing

Күн бұрын

Пікірлер: 34

@adiem1653 3 ай бұрын

Perfectly needed at this time for me 😊

@chadssilversmithing 3 ай бұрын

I’m really glad Adiem!

@rochellebg 3 ай бұрын

Lots of good info here. Cup burs also work great for smoothing wrinkly ball embellishments. I love creating texture, and those diamond burs are great for adding texture to your pieces.

@chadssilversmithing 3 ай бұрын

Thanks Rochelle! I should have mentioned the texture thing:). I appreciate you adding that!

@rochellebg 3 ай бұрын

@chadssilversmithing 👍😄

@kimlyons8550 3 ай бұрын

Thank you Chad for this. It was a good review for me. I've had no clue what to do with the ball burs.

@chadssilversmithing 3 ай бұрын

They are great for all-purpose removal of stuff:)

@raving-rambler 3 ай бұрын

with Pepe as a sponsor I'm surprised that you don't use sunburst polishing wheels - Dedeco is a great brand and they allow you to get really great finishes. Love your stuff Chad!

@chadssilversmithing 3 ай бұрын

Technically, I am an Affiliate of PepeTools. I'll have to try some of those though. Thanks.

@toinettevanschalkwyk8378 3 ай бұрын

Great advice. Thanks 👏

@chadssilversmithing 3 ай бұрын

Thank you Toinette!

@Vgudorf 3 ай бұрын

Hi, Chad. Love your videos! But, I’ve been mystified by something for a long time: Why don’t you use a flex shaft or micro-motor polishing tool in lew of the Dremel? Not even a variable speed Dremel gives you the ability to work at almost infinitely variable revolutions, from almost zero to full throttle. When I started out, I used a Dremel, but was quickly frustrated by the inability to work at extremely slow speeds when I deemed it helpful. My Foredom was such a good purchase, and wasn’t prohibitively expensive-less than $300. The foot petal control gives me much more control than the Dremel, and it’s actually safer to use than a one. Just curious…

@chadssilversmithing 3 ай бұрын

I do have an old Foredom that I picked up second hand, but it doesn’t work very well. I keep thinking I’ll fix it, but never seem to get around to it. I’ll eventually save my pennies and get a new one:)

@tonialvey3386 3 ай бұрын

This was a very useful video. I have definitely been confused about what bits to use. Thanks.

@chadssilversmithing 3 ай бұрын

You're welcome Tonia! I'm glad it was helpful:)

@Liza-fh7rm 2 ай бұрын

I love your videos 😊. Your technique ones, like this, are invaluable for the likes of me, who only recently took this up as a hobby. As a newbie I could do with some covering sorting things when they go wrong 😊. I was soldering two pieces of square wire together and one raised up so I was left with a step instead of a level piece (on the infinity knot pendant) and no idea how to go back and correct it. Thanks for all your work

@chadssilversmithing 2 ай бұрын

Thanks Liza! With a little practice you can keep the piece at just the right temperature to keep the solder in a liquid state and push the piece back into position, remove the heat, and it’ll resolidify in the right position. This kind of thing happens to me pretty frequently:)

@booqoh9845 3 ай бұрын

What would you recommend to file down the sharp edges of the filigree on a silver bangle bracelet

@chadssilversmithing 3 ай бұрын

I'd have to see it, but the blue silicone abrasive wheel would smooth things without endangering fine details too much.

@maryleemartz3722 3 ай бұрын

Chad, thank you so much for this video!! I know this was for me, because I needed it!

@chadssilversmithing 3 ай бұрын

Must have been:)

@johannaverplank4858 3 ай бұрын

You always give great advice. Thank you!!!

@chadssilversmithing 3 ай бұрын

Thanks Johanna:)

@Gazz_R 3 ай бұрын

I love the silicon wheels, they work a treat.The split mandrel is one of my fave attachments, I use mine for sanding and polishing. Thanks for sharing Chad and take care.

@chadssilversmithing 3 ай бұрын

Thank you Gazz:)