Router Jig for Wooden Blinds and Louvered Doors - Woodworking on Handmade Channel

To do my next woodworking project - I needed a jig to cut slots for kinda wooden blinds.
this is how it turned out
----------------------------------------------------------------------------------------------
The song "Is That You Are Are You You" belongs to the performer Chris Zabriskie. License: Creative Commons Attribution (creativecommon....
The original version: chriszabriskie.....
Completed by: chriszabriskie....

[@HandCraftChannel]

Buy me a coffee ? www.buymeacoffee.com/tarassych

[@BroomfieldRR]

Slow the video down and narrate it, so it's useful, and I'll consider the coffee.

[@brucesturtevantwoodworking]

Ditto@@BroomfieldRR

[@therestorationshop]

Two at a time is genius! Thanks for sharing!!

[@josephmreeves2962]

that is the best jig I have seen. I wish you would slow down and explain angles.

[@snazzguy751]

Look at the jig. they are 45's

[@rickgordon8377]

Most excellent jig!Necessity forces us into creative genius doesn't it? Maybe I will. Figure it out when I turn 75

[@joseyrigoyen8890]

¡Excelente video!

[@sammyboy75771]

Exactly what I needed to know! I am now empowered! Thank you.

[@HandCraftChannel]

have fun now :)

[@GregWallis]

OK, you've made me feel inadequate. Brilliant, this is just what I needed to understand. Many thanks!

[@bobstone2720]

Thanks to your video, I was able to make this gig. I have made 11 shutters so far, I’m working on nos. 12-15, and 28 to go after that batch. A 3-year project. In my case, to replicate my 70-year-old shutters with maybe 15 coats of paint on them, I calculated a 67 degree angle. Each shutter has 32 slats. My channel is 2.5” wide and 1.5” high. The snugger the better, but too tight and it’s hard to push the stiles through. Instead of the drill bit separating system, I made an overlay template and I can quickly and easily mark the stiles exactly where to line up each of the 16 cuttings for the top and bottom sections.

[@HandCraftChannel]

really happy it helped you! good luck with your project!

[@WalkersWoodworks]

Mind blown right now. Why can't I think of this stuff! lol

[@brucesturtevantwoodworking]

Nicely done!

[@SGuilarducci]

Excelente vídeo 👍🏻

[@mrjp2149]

Pretty ingenious! Nice work

[@HandCraftChannel]

thank u, man!

[@stevestahl6063]

In the second part of the video where it is normal speed, and you are doing both sides of the frame for the louvers, it looks like both sides are separated by another piece of wood. Am I seeing this correctly? Or is it just two halves pressed together. In either case, did you screw them together to prevent movement? At first I thought it was one piece of wood that you could cut later, but I don't thinks so now. Thanks for the video. I like your jig the best of what I have seen on youtube (though I wish the first half went a bit slower.

[@joaocampanella7202]

Beautiful intro!

[@EmileJrManigat]

Thank you .

[@cornenho]

simple and nice

[@HandCraftChannel]

thank u!

[@cornenho]

And now I come back to see it again, because I m gonna make this!😊

[@robertopullia2049]

Bravissimo, complimenti! Ciao

[@garzonlaperle9403]

Did You make it with Woodbex?

[@djpaso640]

Good idea!

[@HandCraftChannel]

thanks!

[@juginstr1019]

Thank you,well done.

[@dorupopovici5851]

What size is the router bit and also what size is the drill bit you insert in the hole for getting correct distance ? - is there another video about doing the wood slats that make up the louver ?

[@tarassych]

drill and router bit are both same - 8mm, distance between cuts does not depend on bit size here, only to the plywood template

[@telosfd]

Superb! 8 mm cutter bit?

[@HandCraftChannel]

yes, that time I used 8mm bit

[@Jon_Abel]

Good work. Where are you from?

[@HandCraftChannel]

Ukraine

[@StevieBoWillie]

I hope you are safe.

[@mustafaaslan5122]

What is the angle of the louver cover?

[@HandCraftChannel]

in my case it was 45 degree

[@mustafaaslan5122]

@@HandCraftChannel Thanks, the video helped me a lot.

[@rigovega4521]

Buen trabajo! De que medida o ancho son las ranuras o canales?

[@HandCraftChannel]

thank you! slot size is 8mm x 30mm

[@rigovega4521]

Muchas gracias!!

[@pabloramirez3123]

EXELENT

[@HandCraftChannel]

great you enjoy it :)

[@arnulfoacevedosoto7956]

Amigo cuantos grados de inclinación tienen las ranuras o canales

[@HandCraftChannel]

I made 45 degrees

[@pepitolozano1503]

Medellín Colombia fabricó persianas movibles sistema invisible

[@ManuelaAzueta]

Useless to make a video this fast if your intention is to teach someone

[@alanroberts7570]

Videos that have annoying music, speed up by a big factor, have no dialogue are a waste of everybody's time.

[@romaineathey2690]

This time I'll use woodprix instructions to make it by myself.

[@mikerice964]

Bad table saw form.

[@kidonaboat]

music is annoying!

[@wetspotswimwear1199]

When a person makes a six minute video, that could have been done in 45 seconds.... It's worse than a 20y old girl with a video trying to explain how a curling iron works