ROWIN NOISE GATE PEDAL DEMO

[@Hanaiman29]

I learn about noise compression in just 5 min from you. Simple and straightforward. 👍

[@jettisontee4178]

Wow thanks! Stay safe

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@vincentvidal3305]

Thank you for sharing, a perfect demonstration of using a noise-gate! At less than $20 it's worth it to deprive yourself!

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@jhnkouju8724]

Just sharing from playing experience - Any noise gate type pedal should be placed 'before' overdrive, distortion or time based pedals. The only pedal before noise gate should be either tuner pedal or pre-amp.

[@rakibulalamsamrat6311]

Okay I will try it today

[@imamreza6498]

For boss noise reduces maybe yes, but for this product best place in Post fx ( after preamp)

[@jettisontee4178]

Thank you this is noted

[@DJRickDawson]

any good for pedals that leak with no signal going through it? eg. you can still hear the phasing sound of the electro harmonix bad stone (smaller enclosure version) when there's no signal going through.

[@koypi5051]

Wouldnt the noise gate being after the distortion would lessen the distortion? Arent noise gates better at the start of the chain to supress the noise before it even hits distortions?

[@jettisontee4178]

It will depend on you where you put it.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@tulioreisperfilmusical586]

Perfect. That's exactly how I would test the pedal haha. I was curious about this pedal brand.

[@jettisontee4178]

Thank you for your comment!

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@Paul_Lenard_Ewing]

The Rowin Noise Gate is a re-branded Mooer. Not a single part is different from the Mooer. Mooer make the same pedal for over 25 brands last count. The circuit is virtually the same as ISP Decimator. In short the pedal is steal at the price.

[@naturepark4684]

Thank you for your information. .25 brands? Can you mention some of them?

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@aegisraven1284]

Wrong it's not a mooer.

[@batuksri]

Meat of the matter starts at 1:41.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@batuksri]

@@jettisontee4178 done.

[@jettisontee4178]

Thank you so much!

[@warren4838]

do you turn off the noise gate if you're gonna use the modulation?

[@jettisontee4178]

No

[@warren4838]

@@jettisontee4178 what would be the best way or settings of I'm gonna use modulation? because if I don't turn off my rowin noise gate along with the distortion, the noise gate cuts or suck the modulation, thanks for the help,

[@jettisontee4178]

@@warren4838 you need to raise the level of the distortion to compensate for the effect of the noise gate. The higher the threshold, the higher the level of distortion. So that the signal will still be the same or weak.

[@markusaurelius777]

@@warren4838 Modulation should always be in the effects loop....same as delay and EQ

[@Daniel-ld3hm]

Hi awesome review ! What do you think of this pedal vs the Behringer NR300? Both are almost the same price

[@jettisontee4178]

I think for Noise Reduction their the same. They both serve their purpose, but the NR300 has more features.

[@Daniel-ld3hm]

@@jettisontee4178 yes ! Having a knob for the decay has a slight more appeal than just a "hard/soft" toggle. Have you had any experience with it ? I've seen some say behringer eats your tone even at lower thresholds

[@jettisontee4178]

@@Daniel-ld3hm i just use the Hard mode toggle or for the Decay, its on the 10 oclock position. Thats usually my setting while using the noise gate. Yes noise gate will have an effect on the sustain and tone depending on the threshold level you use.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@MrCM25]

Works for bass?

[@jettisontee4178]

Maybe

[@fanigallagher]

Does it cut delay trails ?

[@jettisontee4178]

No

[@kadugbuss]

In general, just place it after the gain pedals and before other effects, you should be fine with delay, reverb, chorus, etc...

[@batanguenongmangyangaming7907]

Always put the noise gate after dirt pedals and before reverbs/delay

[@philiptownsend8348]

Yes it does, I’ve tried it

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@batanguenongmangyangaming7907]

Will it affect the sustain?

[@jettisontee4178]

Yes, adjust the level to compensate.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@arwina.amoguis4183]

It is compatible on a zoom g1xfour pedal?

[@jettisontee4178]

I think so.. Pls subscribe. Will help me big time!

[@Funkfreed]

Past 1 oclock naccut n nya guitar signal sainyo rin b boss?

[@jettisontee4178]

Yup, @2:30

[@Funkfreed]

@@jettisontee4178 alright got it akala ko kase sira nakuha ko. thanks..hehe

[@KazuyaST]

Single coil guitar?

[@jettisontee4178]

Humbucker Sir

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@ScoobieSwisher7413]

Just got one, when I hit the button it kills and mutes everything, no sound at all cant hear guitar, made my amp pop, was in front on 6505+, now I'm afraid to even try again or try it in the FX loop, Anyone help me? Thanks

[@jettisontee4178]

Try to adjust the Threshold Knob until you get the desired level of Noise Gate or Noise Reduction. Hope this helps.

[@ScoobieSwisher7413]

@@jettisontee4178 I tried that on the FX loop, it worked at first, then it popped again, and kills everything, after it does that it does nothing but make loud noise and feedback. It would also go silent if I raised the threshold dial past 4, when it was working

[@jettisontee4178]

I suggest you double check on the following: 1. Guitar Grounding/shielding 2. Cables 3. Power Supply (are you using daisy chain or indipendent power supply?)

[@ScoobieSwisher7413]

@@jettisontee4178 all new ernie ball cables,.9 volt chain supply that powers my polytune and boss flanger with no problems

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@Funkfreed]

Walang hum yung gear ko pero pag tumutugtog ako ng rock may overtones lage since high gain eto po b sagot dun?

[@jettisontee4178]

Things to consider: 1. Guitar should have no hum 2. Cables 3. Power supply of your effects Yeah you can try Noise Gate to make your high gain tone tighter and less noisy 😁

[@Funkfreed]

@@jettisontee4178 dun ako s tighter kase d ako ganun kagaling magmute ng strings. Hehe

[@jettisontee4178]

@@Funkfreed yup, makakatulong tlga noise gate. Tapos yung Fast Mode.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@akosidoogie901]

idol yung sakin pag pinagsabay ko yung distortion at overdrive malakas ground nya,maalis ba ung pag may noise gate pedal ka?.wala pa kasi ako nun.

[@jettisontee4178]

Oo master. Yung s demo ko na ito. Distortion Pedal gamit ko at sinagad ko gain nyan. Nung binuhay ko ang Noise Gate Pedal ay nawala, iadjust lang ang threshold sa desired level ng noisegate. Sana nakatulong. 👍

[@akosidoogie901]

idol thank u sa info,bili na ako ng noise gate ko,done sub na din ako sau idol,goodluck sa channel mo sana lumago pa.

[@jettisontee4178]

@@akosidoogie901 maraming salamat Master. At goodluck s tugtugan mo. Enjoy!

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@kcrichannatv6926]

Sir dpo ba nàapektohan ang clean tone kpg on and off yang noise gate?

[@jettisontee4178]

Depende na yan s setting ng threshold mo. Meron yang certain spot na sakto lng for both your dirt and clean tone, yung pinaka tahimik para sayo. 😁

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@aliceaubrey471]

Sir bago po ba mag american joyo. Nyo sya nilagy sa chain ?

[@jettisontee4178]

Yes. American Joyo is the last pedal on my chain.

[@jettisontee4178]

You may check my other videos po showing the whole pedal board setupfor your reference. 👍

[@aliceaubrey471]

@@jettisontee4178 okie sir hanapin ko po sa channel nyo salamat po

[@jettisontee4178]

@@aliceaubrey471 thank you!

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@ctaburnale]

Can you use this on a regular practice amp like 10 watts bro without pedals and just the built in overdrive?

[@jettisontee4178]

Haven't tried it yet. I will try then will send feedback. Thanks For your question.

[@miloszivkovic6256]

This is done by putting the noise gate into the effect loop of the amp unfortunately cheap amps usually do not have effect loops.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@domvalhalla7771]

​@@miloszivkovic6256not necessarily, gates can be at the end of the chain, after the overdrive or distortion, in front of the amp, then you can continue with modulation, delays and reverb without problem

[@lucasmiquelino-oficial5539]

Incrível

[@josephpaladmartinez1777]

Idol saan mganda ipwesto itong noise gate sa pedal chain?

[@jettisontee4178]

Now, sa kahulihan ko sya nilagay. Para lahat ng noise from other pedals ay macontrol nya.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@miggygatchalian7886]

Dito ko na appreciate tong Plexi-M. hahaha makabili nga

[@jettisontee4178]

Wow! Salamat! Enjoy!

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@xaviercoachlee6908]

Is it normal that my guitar buzz louder when i use gain? im using a strat single coil i know the buzz is normal but when i use gain on pedal or amp it buzzes so loud is it normal? Strat single coil din po ba gamit niyo bossing?

[@jettisontee4178]

Yes, especially for single coils. You can provide shieldings inside the guitar cavity to reduce the hum. Same case with my guitar, that is why I used Noise Gate Pedal to eliminate that buzz/humm sound even if I use Distortion Pedals. Hope I answered your question correct. Thanks and Stay Safe.

[@xaviercoachlee6908]

@@jettisontee4178 Maraming salamat sa fast reply bossing you solved my problem!🤘🏼

[@jettisontee4178]

@@xaviercoachlee6908 wow! Thanks! Enjoy!

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@dummydummy8751]

Nice Demo

[@jettisontee4178]

Thank you

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@jamiesmith1151]

Do you put the gate in the fx loop and other pedals in front of the amp

[@jettisontee4178]

I put the Noise Gate After my Distirtion Pedal on this set up then my modulation effects and then the amp.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@p10rambo]

Use a wireless system instead of a noise gate…this is a ground loop noise

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@joenuevotv3827]

peru pag nasa one o'clock at babalik ka sa clean tone, anu mangyayari? gusto ko malaman sir

[@jettisontee4178]

Ang mawawala ay yung hum ng guitar or any hum sa chain. Para sa setup ko, yung 1 o'clock setting ay sakto lng para hindi din humina masyado ang signal at para humina ang tunog. Minsan between 12-1 ang setting ko, depending sa tone.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@jeriGuitarS]

Sustain is cutting😂😂

[@jettisontee4178]

Yeah 😅😅😅

[@aohn9275]

ganto dapat mag demo

[@jettisontee4178]

Salamat!

[@kamenshik83]

Фон страшный стоит у вас! У вас заземления нет, сделайте заземление хорошее, и фон пропадёт. И педаль не нужна будет

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@yoyongoterovlogs3045]

Jettison tee music, done subscibing pari, Sana mapuntahan mo ako .👍

[@jettisontee4178]

Done Sir. Thanks!

[@hanten10]

First rules to shut down noisy rig is not to buy a cheap pedals and don't use cheap cables

[@norfolknwhey4787]

Not really. You’ll get more signal noise from unclean power coming from the wall, and ambient interference than just about anything else. Shielding/grounding and power source is most important.

[@TheFlyingEpergne]

@@norfolknwhey4787 this. I had a super ghetto 9v power supply plugged into a 6 port daisy chain cable and my overdrive and chorus pedals would hum. I replaced the power supply with a voodoo labs PSU which isolated each pedal and now there's no hum at all. It's amazing

[@norfolknwhey4787]

@@TheFlyingEpergne I had the same issue whenever I would turn on my tube screamer and octave pedals. It took me forever to figure out it was the power supply and not the gear.

[@jettisontee4178]

Pls subscribe. Will help me big time!

[@aegisraven1284]

Its an ok pedal but doesnt match the boss noise gate

[@jettisontee4178]

Thanks, though this is a budget pedal 😁

[@aegisraven1284]

@@jettisontee4178 yes I own it. Hence I know the capabilities. It's also not a mooer clone.