Just did my mid perch, I did not have to remove steering knuckle as suggested and I was able to install both spring compressors with the nut on bottom. Trick is to install spring compressors when the suspension is fully extended vs being slightly compressed. Also I did not have to increase the jack to further compress spring, was done in 30 mins per side. Thanks for video guys!
@valken77777772 жыл бұрын
What do u think the purpose of having the spring compressor nut on top and bottom?
@Arthur-dj8im Жыл бұрын
@@valken7777777simplicity, it was just easier for him.
@paulbourgeau5378 Жыл бұрын
Just did this mod a few days ago. My shocks were on for about 1 year, just starting to see Wisconsin winters. I struggled with the first one because the clap placement was not right. KEY: Definitely follow where they have the clamps placed or the spring will not compress evenly (my issue). I to had issue with the decal, moving the collar up was not easy but I got it in. And if you compress the springs enough, you CAN get the set screw back in. You can do this with just the end link disconnected. Nice video guys!!
@aiiraciing10 жыл бұрын
I noticed you didn't tighten the set screw after moving the retainer clip, is there a reason for this or was it just over looked?
@JMVC11 жыл бұрын
Just wanted to say that I did this with a buddy in just over an hour for both sides. This is the best way to do this mod while getting to know your truck a bit. Save the money and use it to put on a better exhaust. Just make sure to get it aligned afterwards. Thanks RPG!
@bigstunt13 жыл бұрын
Thank you for this. I did it in my garage in about 3 hours. I had two issues. Couldn’t get the set screw out, so I had to add heat with a butane torch to the collar. Secondly, there is a decal on the shock that made it really hard to move the collar up. I recommend removing that decal first.
@TheJoedaddy8315 жыл бұрын
I know this video is 6 years old but it sure would be nice if they would reply to posts on their video.
@ajjamula2 жыл бұрын
You FKN had me rolling and peeling my floor off hahahaha, You fkn killed it at 2:30 to 2:40 and mind you I see your video, any of your videos actually for the very first time, I can't fkn help but you got yourself a subber! I cried, I thought I'm gonna fkn die laughing, lolski bro, love from NoRiL Northern Illinois! Gen1 bolz out👍 and thanks for the tip
@downforce1378 жыл бұрын
i think this video is more for ultralow mileage or new trucks. Any miles, winters or offroad trips is going extend the time in the garage. i removed the shocks after spending about 3hrs trying to do one side on the truck. both set screws were seized, and I didnt have the exact spring compressors they use in vid, so i could really only grab the spring at 8 and 4 if looking from the top. Its only a few more nuts and bolts to remove the strut, so that my recommendation if your truck has over 5K mi, been thru a winter where salt is used, or has been in the mud 3 times.
@Turboriggin11 жыл бұрын
Just did mine alignment is needed make sure you put the set screw back in and also the racket strapped to the hood is alot of stress on it I just wrapped it around the top of the upper shock bolts worked awesome rides great and still does wicked donuts a must have mod!
@DoneSonjaMiguel7 жыл бұрын
Get the F150 Rear Shackle Kit From Rough Country + 2 new Spring Bolts with Nuts, you'll have to use a cutting wheel to remove the factory upper bolts on a Raptor, 1-2" rear lower is the result.
@HDJewBagel6 жыл бұрын
Don Miguel why lower a raptor!??!!?
@gbb14198 ай бұрын
How much lift you get on the top perch and mid perch? And can i throw these struts into an XLT or do i have to buy the Raptor SVT LCAs? Will they fit in stock LCA?
@sutterkramer25487 жыл бұрын
Is there a ride quality difference? Thanks
@Carlos-rz4wv10 жыл бұрын
I actually just made this adjustment and this video an awesome go by I used a C clamp to hold the coil onto the top of the coil bucket and the set screw is a 3/32nd I'm sure that's what they meant to say.
@damnimcooltom14 жыл бұрын
I was curious about 8/32, since that's 1/4. Thanks.
@terryleimonis8 жыл бұрын
After pulling my shocks off several times, the set screw does nothing but prevent the lower perch from rotating when installing the spring. It really doesn't touch the body or act as a set screw. Personally, pull the shock off, you will need more tools and a bit more time but you can compress the spring so much easier. Plus, all you then need to do is pull the tie rod end, upper control arm, and sway bar bolt and then get at the shock hardware. From there, mark the lower bolt in relation to the lower control arm and you have your basic idea of how tight it has to go bac in
@JoseLopez_88209 Жыл бұрын
So you don’t have to tighten back the set screw?
@Sk8boy29711 жыл бұрын
Wow guys! I played $300 for an of road shop to do it and I Have all the tools you guys used! That's awesome! Is it possible for top perch?
@MrHobbs1911 жыл бұрын
Didn't see him tighten the set screw back after moving the perch up? Is that necessary?
@colinlindgren73784 жыл бұрын
Does anyone know if you have to put that screw back in? Or just use the retaining clip?
@chriscansler84087 ай бұрын
Does the 2019-2021 live valve have 2 perch settings like this one?
@USAVMI109 жыл бұрын
This process took me much longer!! If you have any type of corrosion or anything like that on your truck, it will make this process DRASTICALLY more time consuming.
@SSgreen099 жыл бұрын
how do you re-tighten the set screw on the perch?
@thebigone0229 жыл бұрын
SSgreen09 Same thing I was wondering.
@adenseay45134 жыл бұрын
That ring is the only thing keeping that spring from coming off?
@v2iper3 жыл бұрын
Yup
@5ohh38 жыл бұрын
what is the point of removing the nut from the roll bar?
@MattsQuestion11 жыл бұрын
Does this change the factory ride in any way? Little stiffer perhaps?
@NANDOSVT11 жыл бұрын
Is alignment needed after this perch lift?
@wesleyredmon5 жыл бұрын
Yes
@DigiDog123111 жыл бұрын
Yep they missed that out - in reality the pressure on the perch would stop it rotating as would the spring, but if a top mount were to seize then spring rotation would be at the perch
@Reggiestreet9 жыл бұрын
Stupid question but this lifts the front end right?
@NANDOSVT11 жыл бұрын
How much would RPG charge for the perch adjustment? Thinking about the middle perch on my raptor
@urieltazz2814 жыл бұрын
Can i mid peerch if i have leveling kit already?
@jamesgrieves74499 жыл бұрын
how did you get that set screw loose?
@sbushkin6 жыл бұрын
Is an alignment necessary after this? I always think that if the tie rod is disconnected = alignment or is that incorrect?
@charleshenson41836 жыл бұрын
Always a good idea,not because of the tie rod so much as the new geometry with the lift.
@5150Reaper5 жыл бұрын
Scott Bushkin yes
@chief74148 жыл бұрын
is there a mid perch mod for the rear suspension so that the front of the truck is not higher than the back
@5ohh38 жыл бұрын
I think the rear suspension is situated where it is higher than the front end. Even when the front end is bumped up to the 2nd notch, it will be pretty much even.
@fitster68 жыл бұрын
Chief I got my mid perch done, it pretty much levels out the truck
@5150Reaper6 жыл бұрын
fitster6 what’s a rough estimate for the labor?
@SkoalTide962 жыл бұрын
@@5150Reaper 200-300
@senditsillly14236 жыл бұрын
How can I tell what Perch my shocks are set at ?
@senditsillly14235 жыл бұрын
if you dont see the notch at the bottom of the spring and just above the F on the fox then its at the low perch.
@Ger29510 жыл бұрын
Well these guys lost all credibility when they even mentioned the set screw, not when the forgot to put it back in. "8/32" give your head a shake, there is no such tool you could ever pick up that's 8/32nds. Now if some of you are reading this and not picking up what I'm laying down, 8/32nds is and always be 1/4. Not to mention the set screw is no where close to that size. Besides that all you're gonna need is a left handed 15/16ths wrench and can of elbow grease and you're rocking.
@robinjohnson30863 жыл бұрын
I think so
@DoctorTorque4 жыл бұрын
Here's what happens when the shocks have been on the truck for a few years already: kzbin.info/www/bejne/h2q5ma2thLljpKc
@p_hat5 жыл бұрын
5/64.....
@roscopeeco14 жыл бұрын
This video ensures that I won't subscribe to the channel. They can't even answer questions
@damnimcooltom14 жыл бұрын
They haven't uploaded a video in six years, so a subscription is probably worthless.
@Bronkey4699 жыл бұрын
DO NOT DO THIS!!!!!! Just blew my front shock doing mid perch this way...
@downforce1378 жыл бұрын
+Mountain Noobs Your shock was already blown, and low on oil.. when you compressed the suspension, it pushed the oil out of the seal. mine just did same thing on one side..