How to replace the cvt transmission in a 2012 Nissan Altima 2.5l

[@raveservice3749]

This ranks as one of the best ‘how to’ auto videos on KZbin

[@s33therfan]

Thank you so much.

[@luisi9873]

I agree, great job!!!!

[@davidbanks2700]

​@@s33therfanwhat about the reprogramming or relearn process or do you not need it due to you continuing to old tcm? Please respond 🙏🙏🙏🙏🙏🙏

[@wesleydeer889]

@@s33therfan I fix and flip cars, have watched countless 'car fix' vids... your camera work is fantastic.

[@devinburks6721]

Great video . I just changed a transmission in a 08 Altima and I came back and referenced this video at least 6 times . Very descriptive and informative thank you .

[@s33therfan]

Thank you for the great feedback , much appreciated.

[@jam82us]

Was there much difference from the 2014 and the 2008? Can't find many videos for the 08

[@amyalashel1647]

Mines is a 09 and I’m having mine replaced now , how has yours been running since?

[@nick-bj4ix]

THX...THIS WAS A LIFE SAVER FOR ME. GLAD THERES PEOPLE LIKE YOU WHO TAKE THE TIME TO PAY THESE TYPES OF VIDEOS

[@s33therfan]

Thank you very much for the great feedback.

[@Cadzan]

I think you did an amazing job with your video and put in details that give many people the confidence to tackle this job. Couple of things I learned replacing the CVT transmission on a 2010 (1) they are only two large bolts that hold the steering rack on to the subframe I zip tied the steering rack to support it and undid the two bolts and never looked back. Save me quite a bit of time. I don't think there is anything wrong with your method just a suggestion. (2) there is a small bracket which retains the shift cable I took that off. Took a piece of angle iron and fabricated a small lifting plate. It worked very well when removing the transmission pretty good balance point. With the torque converter installed on the replacement transmission it was a little heavy toward the bell housing but not by much. As I say just a couple of ideas and things that I found that help me I hope this helps all those that have taken the time to watch your very well put together video.

[@s33therfan]

Love this comment. Thank you for taking the time to share.

[@tylrum5510]

​@@s33therfan....I can see the shaft side of torque converter is in center of flywheel and almost certain spindle side is in the trans side and the cv shaft is in but can't get transmission to come all the way together .... Anything you can recommend on bringing the transmission close enough to housing to bolt it together?

[@camarogs1]

No need to take the steering column shaft loose. Remove the bolts holding the assembly to the subframe then wire each end to hold it up away from the subframe. If the sway bar is still attached to the subframe it will swing up and over the steering assembly while lowering the subframe. Save a lot of work, no need to undo power steering lines. Just did one of these yesterday.

[@cameroncabrera6476]

Shut up nerd I’m doing everything exactly like in the video. Even loosening the wrong bolts and retightening them

[@PrintTech-3D]

Thank you ❤ you saved me a lot of trouble

[@raveservice3749]

This video was a great help. I went ahead and removed the transmission today, but chose to do something different. I used bungee cords and held up the steering rack, and that way I did not have to do the extra work. Getting the transmission out was not as hard as I thought. Actually it was a breeze. The new (used) tranny goes in tomorrow. Thank you for being such a great help to many like myself

[@s33therfan]

Great job and thank you for the feedback.

[@raveservice3749]

BTW, I spent 2 weeks watching the video 😅

[@s33therfan]

Thank you for watching , much appreciated.

[@gabrielpanoussi]

Awesome video! I just bought a 2012 and heard about the issues with this transmission. I feel relief knowing that it’s now t that bad of a job. Glad you don’t have to remove the motor to get it done. Excellent video thank you so much!

[@s33therfan]

Thank you so much for the feedback.

[@robinberrt1976]

Thank you so much. This is only six months old and I can’t wait to watch this. Because I just bought one of these and it has 120,000 miles on it. And when you said it gets stuck in second gear, I know that this is going to help, you confirming that it should’ve been a recall in regards to this transmission problem

[@s33therfan]

Glad this video can help you out. I really appreciate you watching and the feedback.

[@dudleybonvillain1964]

Huge thank you..this video is alot help for me. I'm in middle swapping my transmission in the same car and your video is a huge help thank you

[@s33therfan]

Thank you for the feedback I am glad it can help you out.

[@michaelshanley5994]

Great video! I had no illusions that replacing the CVT would be a simple swap out, but had no clue how intricate the process was. Technicians earn every penny they make! Just had my CVT replaced (2012 Altima with 130,000). Was quoted $3500 for rebuilt, $3900 for new (Northeast Louisiana area). Went with the new.

[@s33therfan]

You made a great choice going with the new. These cars run terrific with the exception of the cvt. I know this one hands down has the best ac of any vehicle Ive owned. Thank you for the feedback.

[@Miltown.Tarzan]

Was the $3900 the cost for the new transmission and the labor to put it in ? Someone I know is selling a 2012 3.5 sr Altima coupe but the miles are around 130,000 so I got some choices to make if you know what I mean

[@karam3770]

Where did you replace it

[@joshruner1348]

Man I got to say you are a champion. No impacts and all by hand. I'm a mobile mechanic and your video caught my eye and I got to say excellent job 👍how long did it take to do this?

[@s33therfan]

I spent around 4 days actual work , but ran into issues waiting on parts etc. , so it took much longer. Thanks for watching.

[@mariojimilinares]

I completely agree! 👏🏼👏🏼👏🏼

[@Banana-handyman88]

Great job man we appreciate your patience for explaining us so detailed how to do this ourselves! Hi from Canada🇨🇦

[@s33therfan]

Thank you for the terrific feedback , it is greatly appreciated.

[@alexleroy6640]

I recently did a 2009 altima cvt transmission . Ibremoved the tranny from the top. No need to drop subframe and whhel alignment later.. I drained the coolant, remove ai box and components. Disconnect all sensor to the and flip the attached harness over the engine top. Every is clear as water from there.

[@brownwoodworks56]

I’m in agreement with everyone else on the quality info this video brings. Very well done. I’m really handy, but know nothing about cars. Hope this is similar to a 08’ Sentra. Looking to swap it out.

[@s33therfan]

Thank you for the terrific feedback , hope all goes smoothly with your project.

[@raimom3179]

Thank you for the awesome detailed video. Lots of work filming and editing everything. Liked and subscribed! And hello from Finland!

[@s33therfan]

Truly appreciate the feedback. Thank you.

[@raykennington5893]

Great video!! You made it look easy! Done my. I got it all back together now its hard to turn. I double check all the power steering lines

[@David-hk4lu]

Great video, just a question , can you remove the transmission from the top or would it be best to remove it from the bottom???????? Would love a reposes, am planning on removing the transmission soon.,and thanks for this video 😊😊😊😊😊😊😊😊

[@s33therfan]

I would say the bottom would be the easiest way to go. Thank you for watching.

[@armidiaz9847]

I wish I had seen this video 9 months before. I had to replace my transmission on my altima 2011 but the only problem so far is a leak because I forgot to replace a torque converter seal and I have a code PO500 permanently even after replacing all the speed sensors. Great video 👍.

[@s33therfan]

Great feedback and glad you brought this up. This is a common problem on these Altima transmissions , seen it many times transmission perfect and torque converter seal leaking. P0500 also a common nightmare , transmission otherwise works perfectly yet keeps throwing P0500. Thank you for watching.

[@tmoneyink]

I have a trans leak too, could that be only torque converter seal?

[@alejanzar]

What an amazing video you covered every single detail with patients great editing as well. I changed the step motor In the valve body recently and your video help me clarify some doubts. Where did you buy the transmission? Thx

[@s33therfan]

I found a low miled one on ebay. Similar to the one in this link. Thank you very much for the great feedback. ebay.us/CzvNJI

[@alejanzar]

Hi thanks of your video I did change my transmission, I heard after you did the job you need it to program it at the dealership to function right, did you program yours or just work good after you change it without programming? 🙏 Thx

[@busaboytr]

Thank you sir. Awesome video. Very detailed!

[@s33therfan]

You are very welcome

[@ShaquilleRamesh-dr3zk]

This is such a great and detailed video, question seeing as you had a lot of space up to would it have been possible to pull the transmission from the top?

[@s33therfan]

You would have a harder time pulling it from the top. Thank you for watching.

[@raveservice3749]

This is amazing work!. Great camera work too, and really detailed. Did you need to reprogram the transmission, or is it plug and play for the swap?

[@s33therfan]

No need , thanks for the feedback.

[@robinmurrayjr980]

Great job I'm doing a 2010 altima I did it differently I took it out the top went good. I do have a question do you have to program the transmission to the car

[@rosskrause3926]

My 2012 Altima 2.5l just started the "feels like in 2nd gear" feeling at 149.550 miles..I got the car 2 years ago at 113.000 miles..I added a Hayden transmission cooler that helped a lot,have changed the fluid a couple of times as well,and still this CVT goes out...probably going to find another car because spending $3 + thousand with the engine having many miles with my luck I would get the tranny done,then the engine would throw a rod or something stupid. If I was a lot younger I might have tried to replace it myself,but now No Thanks ! Great video here for the DIY'ers.

[@s33therfan]

Thank you for the feedback and sharing it is much appreciated.

[@mrmartin7131]

You got that brother I don’t mess with transmissions 👍🏾👍🏾😬😬

[@MIkhailCruverov]

Great camera work and easy to follow. Great for a quick reference if you get stuck in a spot. About to do the same one next week. If you could do anything differently to save time what would you do if you don't mind me asking.

[@s33therfan]

Thats a tough one , I would have to say if I had it to do over , I would have everything more organized in advance , and ready to go. Thanks for watching.

[@dmonsa637]

1:43:29 What did you do to fix the stripped threading for that bolt? I experienced something similar upon changing the filter assembly. Over torqued the thread hole for the long bolt

[@TheSprtrooper]

Great job on video, recording and explaining. Are you eyeballing the nut sizes and that good or checking size before recording 😳

[@s33therfan]

I would say a little bit of both. Thank you for the great feedback and thanks for watching.

[@alanlee5541]

Thank you! Great video. It also provide a great tutorial for replacing cv axles or boots.

[@s33therfan]

Thank you very much for the terrific feedback.

[@lox3555]

Really helpful and best video I’ve seen detailing cvt replacement. Thanks for posting this. I have a 2012 same make/model @ 165k when my transmission went out. Trying to decide if it’s worth getting a new 0 mileage transmission or used. Should the used one hold up well compared to a reman unit? What’s a reasonable ballpark if I took it to a garage to have them do the work?

[@jaredwiman1845]

Shop quoted me $850 labor I'm on the EXACT same boat

[@jaredwiman1845]

163k 2012 altima

[@jaredwiman1845]

It was gonna be over $3k for the trans and labor, Nissan dealer has to program new trans

[@s33therfan]

Great question , with my experience with these cvt , I believe a reman would be a better choice , and the added security of a warranty. I am just guessing because I have not priced these at a shop , but I would say a min of 3k . Thanks for watching.

[@lox3555]

@@jaredwiman1845 Kinda funny how it’s happened that way for us both. But my labor quotes were $1400 and $1500, and labor + used transmission were $4100, $5k for reman w/ 3 yr warranty...$5400-$6k at another place, and $4200-$4600 at the third. Wondering where I have to go to get the quoted #s you and OP are referencing :)

[@ElPalo.]

I had to watch this 6 times yet I ended up with 5 random bolts

[@johnathanfavorite9407]

Nice! You have replacements for next time! 😂

[@drebgaming8843]

😂😂 facts

[@ztaticz5961]

First of all good job I’m in the middle of the same job right now. Wen you wen to put trans back on. Did you need a new gasket or seal between the engine and transmission?

[@ztaticz5961]

Mines a 2016 Altima but it’s almost the same process

[@s33therfan]

I did not in this case but it is always recommended to replace the torque converter seal , while you have it out. It seems they always end up leaking even if they were not leaking prior. Great question and thank you for watching.

[@omegaman7241]

good video, thanks for making it. What do you think of the valvoline synthetic CVT fluid ?

[@s33therfan]

I think it works fine. Had no issues with it. If money is no object the NS-3 would be great but in my opinion they are pretty much the same. Great question and thank you for watching.

[@wesleybeauge6035]

Great video. What camera are you using to record? Camera is very clear and crisp.

[@carljenkins5092]

so far my Rogue and Altima have been fine. One is a 2014 and a 2018. I have noticed Auto Zone sells these with a 3 year unlimited mileage warranty. Hopefully mine will be ok. If I get 150k I will most likely be happy. Would you buy a reman from Auto zone or Advance? this is the best video I have seen on this subject. Thanks so much for posting it

[@s33therfan]

I think they do have some good ones , I usually scroll through what they have and then research the quality of the manufacturer . There are also many companies that reman these on the internet and its a matter of feedback they have and warranty. If possible it is best to get one with a good part and labor warranty. Great question and thank you for watching.

[@GB-nu8fq]

Did you buy the transmission online? I was told you have to reprogram the new transmission. You didn't have too? I'm about to replace mine in my 07 so was wanting to know. Thanks

[@s33therfan]

I did not have to program anything . There may be a relearn procedure where you clear all the learned settings from the old transmission. I did not have any issues so did not reset anything. Thanks for the feedback.

[@Sean-lp6px]

I put a transmission from a 2010 Nissan Altima into my 2007 Altima, and ran into some issues. Using the TCM from the 2010, the speedometer did not function and I kept getting codes. When I put the 2007 TCM back into the car, the speedometer worked but I kept getting code P0845. Frustrated, I finally opened the oil pan, removed the 2010 valve body, and replaced it with the 2007 valve body. No more codes.

[@macknumber9]

My biggest fear on doing this job are a couple things number one forgetting where every single different bolt and component goes. Number two would be messing up with the insulation and maybe not pushing the drive shaft far enough in or the torque converter or any of the other components

[@s33therfan]

It is everyones fear , until you build confidence from tackling many projects. Measuring taking pictures , put bolts/nuts back where they go as you proceed will help a lot. Never have loose bolts laying around. Also label everything. Thanks for the feedback.

[@macknumber9]

@@s33therfan thanx for the tips

[@coachmck]

Hello, my car is a 2018 Nissan Sentra, and I was told I have to replace the same part, my question is do I have to reprogram the car after the new value body is in? Will the car be able to drive right away?

[@s33therfan]

You won't need to program anything. Street Smart transmission , does an awesome job on their valve bodies .

[@scottdaniels8230]

Great vid. Thank you for your thoroughness and detail. Did you keep your original TCM or did they send you the TCM that went with your used tranny that you bought? Thanks again

[@s33therfan]

The only thing I used from the original was the rom. I do not even think that was necessary but I had the valve body out so swapped it while at it. The tcm stays with the car , located next to the battery. Thanks for watching.

[@macknumber9]

@@s33therfan so you use the original TCM from the original transmission with the used transmission that you swapped in. Didn't you need to have that programmed?

[@DRBauto]

So did you had to reprogram the TCM?

[@Cruzeyn]

Hey the best video on this job hands down. Thank you. Also what kind of hoist are you using?

[@s33therfan]

I believe it is called a big red it is a 2 ton hoist , I purchased it from tractor supply some years ago. Thanks for watching.

[@Sonnysandhu]

Does the cvt needs programming after replacement? Or Do I just reset the values using scanner ? Getting ready to install a 2012 Nissan Altima cvt tomorrow morning. Thanks

[@s33therfan]

Just reset the values. Thanks for watching.

[@billlawson6757]

Very well explained. I wish I had a library of the job you do no I'll do mine thank you

[@s33therfan]

Thanks for the terrific feedback , it is much appreciated.

[@ninerz49erz]

Could it not come out the top if the coolant hoses and thermostat housing was removed?

[@s33therfan]

If you pull the engine and transmission together it should. Thanks for the feedback.

[@ottobauner9828]

I have a 2012 altima 2.5s I'm fixing to swap the cvt in. I had the understanding after you replaced the CVT you have to have the dealer use consult to put the ecm/tcm in a relearn procedure. Is this true

[@s33therfan]

I have never had to. I can't say if that would be the case with every cvt thought. Great question and thanks for the feedback.

[@makojuicedaniel9307]

Im gonna come out the top, its a little tight but seems way easier.

[@ramiroaguirre7228]

Very nice explanation thanks for the info , I am doing my Sentra 09 very similar,👏👏

[@s33therfan]

Thank you for the great feedback.

[@Ricardom1020]

I've heard these need to be programmed when putting the trans in from another car. How is this done?

[@s33therfan]

The only thing it needs is a reset or quick relearn if anything. Most good scan tools can accomplish this now days even blue tooth type obd2 type devices. Thanks for watching.

[@jungapo2]

i am just wondering why you didn’t use impact wrench.

[@illwill915]

At first I was like wouldn’t it be easier just to use a screwdriver to pop the cap off than take the entire wheel off but then he explained that he made a mistake by not removing the pin.

[@bologna_soup]

Is this generally the same procedure for 5th gen altimas?

[@s33therfan]

Pretty much the same , thanks for watching.

[@Hernsama]

Where are you located? I need to get my Altima transmission replaced

[@s33therfan]

You can reach out to me at [e-mail].

[@fredquillen6608]

Did you have to flash the computer after replacing the transmission because I've talked to a few mechanics and they said if you do replace the transmission that you would have to flash it or take it to a Nissan dealership to get it flashed for the transmission to work right

[@visionarybrushstroker7694]

Did you get the answer to this?

[@tylrum5510]

I would like to know this as well!

[@tylrum5510]

Or if you could even swamp the computer from your old into the used transmission your installing?

[@JasmineRN]

@2:28:00 power steering line leaks after install maybe i just overtighten? Any tips?

[@s33therfan]

Possibily. You might try backing it off and snugging it up again. I have found this method to work with brake lines that refused to stop leaking. Hope this helps.

[@Jessiesuain]

I saved this video I have 2016 Altima with the CVT transmission and it acts like it don't want to get in gear sometimes

[@s33therfan]

Thank you for watching .

[@worldish76]

Hello teacher, my Nissan Altima 2013 2.5 L makes a noise like it is scraping something in the transmission.

[@s33therfan]

These cvt are known for a lot of issues. Definitely a bad sign if it is in fact coming from the transmission. Thank you for the feedback.

[@macknumber9]

When reinstalling the axles and other transmission components my fear is I'm not pushing it in far enough to seat....how will you know you have it all the way in so it is correctly seated?

[@s33therfan]

Great question. When you use hammering action to seat the axle you will feel and hear a solid thud. It will not move any farther. You can also take pictures of before and after to verify the clearance. The knuckle is also near impossible to reinstall if the axle is not seated properly. Thanks for watching.

[@macknumber9]

@@s33therfan thank you....maybe I can take some white paint or nail polish or something and maroon where it all meets so I know everything is seated correctly....what about the torque converter and all the components going into the engine....is there any tricks to that? I am only halfway through your video and I'm watching it all to make sure I comprehend the whole job...I am not skipping ahead

[@whydontmynameswork]

I applaud you for using am manual tools. That’s a rough job with no air or battery impacts/ratchets. I sure hope the salvage yard compensated you for having to drop that valve body though. 🤬

[@s33therfan]

I wish I had sent the transmission back after seeing the broken connector. They refunded a 3rd of the transmission cost but it was not worth it. Ended up having to swap the valve body out for a reman , from street smart , worked awesome after that , but labor and added expense. Luckily this does not happen often and you learn quick which salvage yards/sellers to do business with. Thank you for watching the video thoroughly and I appreciate the feedback.

[@whydontmynameswork]

@@s33therfan swapping a trans in a 2011 tomorrow. Luckily the owner opted for dealer new unit. I haven’t looked at it yet but there is no way to leave the rack on the vehicle and just drop the sub frame is there?

[@raveservice3749]

I installed the used transmission which I was told works, and I still have the transmission whine. What am I missing? Any clue?

[@s33therfan]

If the fluid is level is all good , then I would return it under warranty hopefully. Now if it was making a similar noise prior , then that is too much of a coincidence . I would be looking at some other moving part . Flex plate , cv etc. Thank you for the question.

[@racehard38ify]

I'm replacing my 2011 altima cvt. Im currently looking for one near me. Can you tell me what years will work with my 2011 with no reprogramming?

[@s33therfan]

I am pretty sure a 2007-2012 are all the same for 2.5l. 2013 was a change up year but even 2013 possibly. At most the learned values may need reset , but any shop should be able to handle that. I did not have to program anything on mine. I have replaced 3 different cvt and never performed any type of programming. 2013 rogue , 2013 murano , 2013 altima. Never hurts to double and triple check before getting one however. Hope this helps.

[@racehard38ify]

Great. Thanks for the reply I'm currently using your video to pull mine. Great video and perfectly explained

[@albertorangel2940]

Where did you find the transmission and how much are they going for? Thanks. Great video 📹 👍

[@s33therfan]

I purchased one from ebay , I always check the sellers feedback and warranty they offer. Used will run around $1400. Thanks for watching.

[@albertorangel2940]

Excellent video. Thanks for sharing and helping.

[@tmoneyink]

Hi I have an 08 Altima and there’s a leak where the dust cover at timestamp 54:01 ; would you think it’s a seal? I wanted to know if i can just replace the seal if I open up the trans, or is that not possible?

[@s33therfan]

This will most likely be your torque converter seal. However with the transmission out , I would also inspect the rear main seal on the engine for leakage. However 99 percent of the time , its the torque converter seal , and they are notorious for this on these cvt. As a rule of thumb , unless its leaking badly , it may not be worth replacing due to the work required but definitely keeping a close eye on the cvt fluid , see how much is being lost. Great question , thank you for the feedback.

[@shacobywilliams3703]

How much does this job usually cost? 2012 Nissan Altima

[@s33therfan]

I would say on average shops will charge around 3000 , but it will vary from area. Maybe someone else can chime in , that has had one replaced recently. Thanks for the question.

[@DATRUTH83]

Nissan dealership in baton rouge quoted me 6500.00🤦🏾‍♂️

[@javiernavarro8408]

One question is about of reprogrammed the cvt with the computer of the car one mechanic told me when swap this kind of tranny is true?

[@s33therfan]

Great question. There was no programming needed the tcm is outside the tran next to pcm , basically stays with the car. There is a ROM located inside of your old transmission. I would hang onto this just in case tberes any issues and swap it . None was needed in my case. Thanks for watching.

[@scottcarpenter8434]

Does relearn need to be done afterwards at dealership?

[@peter93plify]

How many hours/days did it take because I think 🤔 you said that it was getting dark outside 🤔

[@s33therfan]

I spent several days . It was rather easy to work on but atleast 3 days . A day for removal , another for tran prep work , a day for install. Thanks for the feedback.

[@freddy1jumper58]

Change the fluid in most cvt transmissions every 30,000 miles, Altima is 20,000. CVT fluid is clear.

[@s33therfan]

Thank you for the tip , I appreciate the feedback.

[@kalieburrows1427]

How different will this be for a v6?? I’m worried I won’t have enough room to get the trans out from underneath??

[@s33therfan]

It will be more cramped , but basically the same process. Thanks for the feedback.

[@codyjohnson713]

Did you have a check engine light on for the bad transmission? If so how did you clear it my scan tool doesn't seem to want to erase the codes

[@s33therfan]

The hard codes remained it seems but the cel cleared itself just unplugging the battery. Seems I used my basic scan tool to clear other codes . Thanks for watching

[@tre2groovytv607]

Did you have the same tcm on the new transmission or new tcm on the new transmission

[@s33therfan]

Same tcm , thanks for watching.

[@marcosmorales854]

Hey man can you help me out I did the install and now my car isn’t cranking it’s making a whirring or humming noise when trying to start it. I didn’t remove the torque convertor when I did the install was I supposed to remove it from the flywheel and attach it to the trans before reinstalling? I’m trying to rotate the crank but I cannot

[@marcosmorales854]

I just realized the flywheel/torque convertor bolts are hitting the block what should I do you think? I have a 2008 Nissan Altima with the same trans

[@s33therfan]

The torque converter must be removed from the flex plate in order to seat the torque converter . You usually need to hear a double clunk( spin clockwise as many times as it takes while pushing) to make sure its seated. Also once the transmission is mated up before putting all the bolts., make sure the crank turns and the torque converter should spin freely using your fingers. Unfortunately you will need to remove the transmission. You can remove the transmission using the method you did , however you have to install and seat the torque converter before installing it. You are not the first person to do this , it happens and usually its just from failing to seat the torque converter and verify its spinning. Hope this helps.

[@marcosmorales854]

@@s33therfan aww man we’ll that’s a bummer we’ll Atleast you made this process very easy and videoed everything I followed every step and wasn’t confused at all when doing it. We’ll Atleast I now know to remove torque converter and install on trans before mating trans. I appreciate your help and hopefully this next weekend I can get everything sorted. So once I click into the transmission will it stay on when I goto install it back onto the motor?

[@s33therfan]

Once you get it seated and mated back up you can then access the torque converter bolts/nuts from under at the access or sometimes where the starter goes. Just make sure and loctite and snug them up. When the torque converter is seated good , it should always pull itself to the flex plate. Thanks again .

[@marcosmorales854]

@@s33therfan ok I will do that. Do you think I might have damaged the transmission or the converter by doing this? Or will I be okay to just uninstall everything and reinstall everything the correct way?

[@visionarybrushstroker7694]

Yo did you have to reprogram the trans?

[@s33therfan]

I did not program anything , thanks for the feedback.

[@djavaresk]

Im getting a u0101 code after doing the swap. Car starts and drives but seems it’s in limp mode.

[@s33therfan]

First thing to do is check all the connectors , more especially the pcm/tcm. Also check the round connector on the transmission. Make certain it is seated and make sure there are no messed up pins. There is really no reason for that code unless , something with the wiring or connectors. ( If there was no code prior ) Swapping tcm will also cause a similar code. It is also possible you might delete the code or disconnect the battery and see if it resets. Thanks for the feedback.

[@djavaresk]

@@s33therfan thank you for the reply. I will definitely check that out tomorrow!

[@helderyoung848]

I did before brother but I pull it,using the up side un the I used a lift joist..I think is more easy 🤔

[@tjack460]

What's wrong with using air or battery impacts.

[@TheSprtrooper]

Your hand can usually tell when you will break a bolt. Long time mechanics could probably do either way. I like to break by hand then use machine to run the rest of the thread. Reverse same. Start by hand so you dont cross thread then machine to almost bottom then finish w torque wrench if you have it.

[@nellz4738]

Where can you get the valve body harness to buy at 1:41:20

[@travisdowler224]

Where did you order the new trans from? Also, was the new one a reman or brand new?

[@s33therfan]

I found a used one on ebay , I will say this check the seller rating , and if there is any issue ebay offers your money back. So if it does not work properly 100 percent , return it. I purchased my cvt fluid from amazon , it was by far the cheapest route. Thank you for the feedback. cvt fluid: amzn.to/3995pib

[@guillermo7189]

Mines is also currently stuck in second gear. Do you have a estimate on how much it cost with parts and labor?

[@s33therfan]

It would be quite expensive , I am guessing around 3000 and up. One thing you can try is replacing the valve body first. You can get a reman from Street Smart Transmission for around $250. You really have nothing to lose and can even return it for a restocking fee. Get your cvt fluid online and you can usually save money there also. There are several videos on installing the valve body and the only trick is inserting a small screw driver to hold the slide fork. Best of luck and thanks for watching.

[@brazy149]

Buddy of mine asked me to do a trans swap for his 13 Sentra. I don’t need to have it programmed after the swap do I?

[@s33therfan]

Great question. The tcm is separate from the transmission so it will not need programmed. That being said there is a part inside the tran called the Rom that will need to relearn . This will relearn over time by itself. Thanks for watching.

[@davidknibbs9646]

Are you taking the transmission out?

[@davidknibbs9646]

Do you have to take the sub frame out to get to the trans out?

[@s33therfan]

Yes , in order to have room to drop it out the bottom. Thanks for the feedback.

[@mattc528]

This is the exact same car I have. I feel like I'm having problems with my transmission the gears are not shifting my car has like 125,200 on it. The sound I hear is it sounds like my muffler. But I think it's my gears not changing

[@s33therfan]

You may be able to get the codes read and see what exactly is malfunctioning. Thanks for watching.

[@amandaackermann6189]

I did my through the top route without dropping subframe. THis route you have to remove thermal stat housing.

[@macknumber9]

I wish you had a video of you doing this because I would love to be able to do it up through the top. I'm also trying to change the transmission on a 2012 Maxima so I'm not sure if it can be done with the altima as well as the Maxima

[@emporium597]

Nice work bro

[@s33therfan]

Thank you for watching.

[@macknumber9]

Is this the same process for 2012 maxima?

[@s33therfan]

It should be very close. Thanks

[@macknumber9]

@@s33therfan thanx for this video man. You documented every single nut and bolt and the whole process with clear explanation of what you were doing....I salute you sir. It is hard enough to do this job without filming but you not only did it but you filmed the whole thing and did it with excellent video quality.

[@efrainvazquez6752]

Hello, thank you for such a valuable video. Is this 2012 Altima transmission identical to a 2007 model? Can I install a 2012 to 2007?

[@s33therfan]

As far as I know they are the same . Thank you for the feedback.

[@charleneandrew1608]

awesome video

[@s33therfan]

Thank you for watching.

[@TheBrunobus]

How many hours did it take to actually do the swap?

[@s33therfan]

I figured on about 4 partial days , so no more than 24 hours . Thanks for the feedback

[@TheBrunobus]

Yikes! Was thinking about giving it a shot myself, but even half that time is too much considering it would be my first attempt ever. I will leave it to a pro on this car (only 49k miles and in otherwise perfect condition).

[@overnepps6019]

Thanks a lot

[@s33therfan]

Most welcome

[@hyperrider4269]

Do we need to calibrate transmission after replacing

[@s33therfan]

I did not have to recalibrate anything. I did wind up replacing the rom while I was in the valve body area. I don't know if that would have made any difference but it may have. Thanks for watching.

[@milygonzalez3726]

Will a 2010 trans fit a 2012?

[@s33therfan]

I believe 2007-2012 are the same. Thanks for the question.

[@milygonzalez3726]

@@s33therfan thx you got a new sub.

[@darr2970]

Hello i have watched a lot of your videos keep up the great work. I am in need of serious help, i have a 07 Suzuki Reno that needs the heater core replacement.so i usually.do all the work on it myself. I need a picture ddiagram of alll the dashboard bolts, screws, nuts, wires im still stuck somewhere and cant get the dash completely loose. Could you please help? I would appreciate it.

[@frankchurch241]

Do you have to reprogram the transmission

[@s33therfan]

Great question. I believe it depends on how close the year of the transmission. I replaced the cvt in a Murano and it required no programing. This one I cannot say for certain , however I did swap ( what they call the rom) from the old transmission, while I was replacing the wire connector. The rom is the small black box on the valve body. Other than that there is nothing I am aware of that needs programmed. Thanks for watching.

[@kalieburrows1427]

The valve body in the pan?

[@shacobywilliams3703]

Are you in Ga?

[@s33therfan]

Ar . Thank you for watching.

[@jorgevids]

Anyone have a vid for 2015 altima trans replacement

[@justinfuller919offroad3]

Is this the 2.5s model?

[@s33therfan]

yes , thanks for watching.

[@JerzyBoy973]

Looks like they got the classic Nissan oil cooler leak.

[@humbertoolascoaga7941]

Followed

[@s33therfan]

Thank you

[@andrzejsniadowski4903]

I just had to replace CVT transmission in my 2014 Nissan Rogue SL AWD.... $6,560.58. Don't buy Nissan cars. Hondas and Toyotas are much better.

[@s33therfan]

Wow , is that dealership price or just a transmission shop. Thank you for sharing.

[@andrzejsniadowski4903]

@@s33therfan The quote was from transmission shop but the transmission installed was a completely new transmission ordered from Nissan dealership. The job comes with 2 year / 24,000 mile warranty on parts &labor.

[@Mr69barracuda]

I'll ya give 4 stars.. You don't get 5 stars, because you say "This, That and thing" rather than what the H^ll it is. You obviously spent a lot of time making this video.. may go through and watch it yourself and add "Captions" where you information is "Vague". Other than that - Thank you for the vid.