Samsung Refrigerator Inverter Control Board Faults Repair Tips

[@bridges5659]

Great explanation ! I am currently working on my Bosch pcb. The surge resistor, flat blue disk and a rectangular capacitor of 1 uF was burnt off which I've replaced but still no power to the compressor. The board has relays which could be faulty. I will continue to repair with the hope that the processor chip is not faulty.

[@jacan3]

Great video, thanks. Could you please figure out how much current or wattage the led port on your board is able to take? I'm wanna boost the light in my fridge but don't know the limits. The led port is running at 12v on my fridge.

[@forevertechenglish]

Dear, I don't have the board right now, Because I gave it back to the Customer after I repaired it.

[@banchasaoraso8591]

yes I staying with this problem and try to looking you short by short. Thankyou.

[@zabihullahpir4766]

Nice explanation

[@nikikolev1978]

Super video !

[@forevertechenglish]

Super!

[@dappareilselectromenagersb2530]

طريقة الشرح ممتازة صديقي اتمنى ان تعمل لنا حلقة على فحص الحسسات وشكرن صديقي

[@rolanddejesus8685]

thank you very much for a very informative and clear explanation...God bless.

[@forevertechenglish]

You are very welcome

[@StephenBoatright-h3e]

Good job great video it’s a pleasure to listen to you!

[@micahcollins1714]

Hi, I have checked everything on your video and all checks out except 1 thing, I am not getting 12v on the low side. I am only getting 6.9V. However I am getting 4.5-5V on the output of the regulator. I have tested every component on both High and Low side. The small relay on the board clicks twice and the ref. and compressor turn on for 2 seconds then shuts down. The relay will then click twice and start up again and basically repeat the cycle. I unplugged everything from the control board just incase it was being overloaded by something else, but it does the same thing. There seems to be a component that is crashing the system. Do you have any suggestions?

[@sunsys0]

Very good explanation of the circuit board. Thanks

[@forevertechenglish]

Glad it was helpful!

[@vernonbartlett4372]

7:50

[@miragecomputronix7396]

Nice explanation.thank you very much sir🙏

[@forevertechenglish]

Keep watching

[@rashidelahi2939]

very nice way explanation.thanks lot

[@paulcir1305]

I bypass all the crap, put a 220 to 15v transformer before the rectifier and voltage regulator. All working now. No problemo.

[@jboyundisputed_guru7861]

Was the bypass made on the IPM PCB board? (The smaller board)

[@zabihullahpir4766]

Thank you for uploading these videos Can you please help me. I have got a samsung american style fridge freezer The colling fan for the coils near compressor is not working. There should be 12 volts power coming in that socket but there is not and there is no problem in the fan I checked the problem is in the pcb board which is not providing 12 volts. Can you please help me which element to change in the pcb board will solve the issue please Thank you

[@forevertechenglish]

Where are you from?

[@PatrickRibbsaeter]

Just found your channel... nice explanation, thanks master

[@forevertechenglish]

Glad you liked it!

[@zabihullahpir4766]

I have got a problem where there is no power for the compressor fan, can you please show me in the board where is the part to change it

[@micahcollins1714]

My exact same motherboard works for a few minutes then sudden power loss. I removed the two blue film capacitors and measured them...one is 0.22uf and the other 0.47uf and both measured under 20uf. Do you think these would be the sole problem of power loss after several minutes? Or is there also another component possibly responsible? Most components if busted will stop the whole motherboard, but mine will start again after I unplug and replug again...but then die before the compressor even gets warm.

[@forevertechenglish]

If the capacitors have got weak, replace them with a new one, if it starts working then well and good and if it does not then you will have to check the board as I have told in the video.

[@grimreaper2066]

Great Explanation

[@forevertechenglish]

Glad it was helpful!

[@shilayusof5370]

If j13 burn what the defect?

[@vincentwelevin4528]

Pls I do I get another PCB panel, mine has gone bad due to wrong conversion by a bad technician. I live in Abuja Nigeria. Please can you link me up on where and how I will get it here in Abuja

[@forevertechenglish]

You may have to contact an authorized service center in your area or get it from a local retailer who deals with spare parts.

[@abdulkhalegaliwan2348]

Thank you very much please you have schematics for this pcb

[@Suavache]

Xin cảm ơn anh đã chia sẻ với khán giả kiến thức sửa bo mạch với khán giả

[@washcuruny3660]

My samsung rt 47 is dead after 1.5 years later. 3 days later automatically running the freeze. Then 1 years later deep freezer fan not running. So, not cooled properly. I checked fan and sensor. Both are ok. Which parts are working for running fan to the PCB board ?

[@songtime6108]

Sir led indicate continuous also compressor running continually chek ntc working properly chek the ntc sensor working properly but compressor no cutoff please give solutions

[@groovzgajolin4100]

What is the value of zener diode

[@jhoraydz4553]

Would this procedure works on other brands? Thanks

[@forevertechenglish]

Nope Because every company and brands design the control board according to their needs, but the basic components which works in the control board are the same.

[@liviuion9651]

A Samsung inverter compresor could ne noisy because of the malfunction of (ipm)pcb?

[@forevertechenglish]

May be possible, but havn't seen one with too much noise.

[@khalifagalaly3632]

Good teacher

[@forevertechenglish]

Thank you! 😃 for your valuable feedback

[@tusharkumarmehta2208]

Very good explanation of PCBs

[@forevertechenglish]

Thanks and welcome

[@KelvinWilson53]

Do you have the correct part numbers for both PCB boards?

[@forevertechenglish]

Right now I don't supply part, will think in the future

[@Julius-ij4id]

Where can I buy pcb board? Do you have on stocks ?

[@AFTABAHMED41]

Good job

[@forevertechenglish]

Thanks

[@upendraudayanga3155]

THANK YOU

[@shaikhfaisal4367]

my samsung inverter pcb having defrosting problem i had checked all heater sensors etc what should i check on pcb...plz help plz help thank u

[@grimreaper2066]

How to check all the possible faults by using multimeter?

[@forevertechenglish]

I have covered almost all the faults, if I get more faults sure I will explain those as well.

[@grimreaper2066]

@@forevertechenglish I know you covered almost everything but what i meant was, by using multimeter how can i check all the faulty components, how to set multimeter for that?

[@forevertechenglish]

Ok now I got you

[@spacespace-pe6jd]

Helo sir ,my Sharp refrigrator pcb main bord stop working model No SJ-PT 591M-BK ...please help up to repair pcb

[@KhodairAbbas]

Very good

[@comlanhuberthounnou9316]

Merci bien vous aviez écouter ma doléances en changeant le sous titre en français merci bien

[@babaolowo35]

Thank u

[@forevertechenglish]

Welcome

[@mpologomafred7754]

The compressor not getting power, what could be the problem?

[@forevertechenglish]

The control board could be faulty.

[@alexisgeorgiou4247]

Dear friends i have Samsung refrigerator and the motel is RT29K5030WW , the fridge when i plug in the electricity ,is working well,and everything is fine,the lights in pcb is working well, everything started working well,my problem is PCB is not getting signal from sensors defrost, to pcb electronic plate,to give time break for resting the compressor,is working with no stop,so when is working long time (about 6-8 hours working,is giving me a signal,in pcb,10 times that my compressor having a problem and is stop working, like is have to be , everything is hot,i have checked all's the defrost sensor up and down with multimeter in k oms,and the compressor also with multimeter, and everything is fine,i think something happened with pcb,is anyone out there, can give me any advice, what happening , where is the problem ,i can not found,is anyone from experience now something ,to give me where is the problem , many thanks reading my problem

[@محمدحسینعاشقی]

❤❤❤❤

[@lameckwillie3407]

I need this pcb board new one can anyone help

[@forevertechenglish]

Where are you from??

[@lameckwillie3407]

From Malawi

[@lameckwillie3407]

@@forevertechenglish am in Malawi

[@lameckwillie3407]

And name the price in usd

[@MsFadyorg]

❤❤❤❤❤❤❤❤❤❤

[@comlanhuberthounnou9316]

Doléances où une proposition de ma part et si c'est possible faite faite le suis preneur et dite moi combien cela va me coûter ,dans ma ville où je travaille sur les appareils électroménagers la plaquette qui alimente le Motor Inverteur frigorifique n'existe pas ,les frigos sont gâtés et abandonnée et si vous pouvez m'aider à avoir la plaquette ah se serait une bonne affaire ,je peux l'avoir à combien avec quel quantité ( le n 50 ou cent)

[@rahulsarkarAMC]

Panasonic refrigerator PCB BOARD repair NEEDED EMERGENCY

[@neutrino_]

I got my answer in just 15 seconds 😂😂

[@forevertechenglish]

No waste of time.

[@neutrino_]

Sir what's the price of this PCB And why we can't repair if microcontroller burns

[@forevertechenglish]

Dear, I don't sell motherboards right now, you can check its prize online. The microcontroller is known as the main IC of the pcb, if it goes bad you can find the ic in physical form, but the program in it is encrypted from the company it is made by. And it is very difficult to decode it.

[@doughill4972]

Why is he calling the opto coupler a rectifier?

[@aboabdrahmanaziz8752]

V g vedeo

[@thambaraspeedbrain1756]

No speed compressor

[@SKMEnterprises-m6d]

Customer vomplaint is Comprossor 5 minuts working then compressor taking then high amps going to off condition, board also full dead condition, then not automaticly restart , when we swith off 2minuts then again board will on condition comprossor also on condition, but after 5minuts comprossor going off condition not automatily restart please give me solution sir thank you

[@PrasannaKumarage-d5h]

මේ සර්කිට් ගන්න පුළුවන් ද

[@forevertechenglish]

අපි මේවා විකුණන්නේ නැහැ, සැම්සුන් ඉන්වර්ටර් ශීතකරණයේ PCB පුවරුව සඳහා ඔබට samsung සමාගමේ සේවා මධ්‍යස්ථානයෙන් විමසිය හැකිය.

[@sissokomakan9407]

Français

[@JoelFrigo]

En français svp

[@kpelectronics]

100 ohms? No my friend , 100 means 10 ohms last zero does not count

[@forevertechenglish]

oh i could be mistaken, Thanks for correcting