BMW E46 Crankshaft Pulley

BMW E46 Crankshaft Pulley amzn.to/3dt4HMr (UK)
amzn.to/37TCz3Y (INTERNATIONAL)

[@Henry_R]

Thanks for good video Sandy! I manged to get it open by using fifth gear and brakes, just in case added spanner to driveshaft flex disc bolt to hold against body. But damn it was tight, I had to use 3/4 sockets and 1m pipe :S I could not find opening to flywheel underneath facelift E46 320d manual, otherwise I would have tried your trick also.

[@sandyande]

Glad to help cheers sandy

[@mattgilbert7547]

Great guide thank you

[@nopy99]

happened to me too. crank pully disintegrated at 110k miles. ststement of the obvious but its recomended to change the belts at the same time.

[@MohVlogz]

kzbin.info/www/bejne/mH-yZJWJl9eNfKc

[@Adam-bw4lw]

damn 420 that crank pulley is high af

[@MohVlogz]

Adam 1 kzbin.info/www/bejne/mH-yZJWJl9eNfKc

[@alanmannion8670]

220K Miles and no pully, but this is why im looking at this video. Thinking of doing.

[@Delboy-jb2ss]

Use a small jack to hold the chisel in place on flywheel if u dont have another of hands ready

[@dimagerman8834]

Hello friend.There is a problem and I'm looking for advice.I have a bmw E46 diesel 2003.The problem is that I'm in the last year changed 4 times the crankshaft pulley, it something BREAKS , but I can't understand.Thank you

[@sandyande]

Dima German hello friend ask these guys kzbin.info/door/Hr8jUDLpkcYgg3Axhu7qhw they are BMW experts, could be partially seized Aircon compressor or another pulley?

[@MohVlogz]

Is your car Remapped? What bhp is it?

[@haiqalhanapi1948]

serious question. what accent are you talking in?

[@klaudiaracz438]

Scottish

[@TehNouk]

why cant i just put it in gear soo i get the crankshaft pulley bolt loose?

[@MohVlogz]

Check out my vid it explain better kzbin.info/www/bejne/mH-yZJWJl9eNfKc

[@Classic_Re-creation]

Is this just a normal threaded bolt left to loosen and right to tighten?

[@sandyande]

Yes it is my friend

[@Classic_Re-creation]

@@sandyande thank you going to tackle mine tomorrow

[@alz722]

Can't you leave the car in gear with some one sitting in it with their foot on the break to lock the engine up?

[@sandyande]

Tried that no chance!

[@raino18]

Did this pulley also cause vibration at idle speed?

[@sandyande]

Yes

[@NG-zg8vf]

Why would u do it in 6th gear? Stick it in first, handbrake on and get that bolt off

[@sandyande]

Tried that doesn't work

[@gocekipro1305]

At which mileage you replace the crankshaft pulley

[@sandyande]

130,000 miles

[@Eddiebayes177]

Dose anyone know how todo with automatic gearbox??

[@erixlast6020]

Nop

[@tewendeblaise7876]

Kia sportaj 2008

[@crni722]

Do not lock flywheel, it put too much stress on crankshaft, use proper tool.

[@sandyande]

Haven't got proper tool, one must work with what one has available!!! I've had no problems since repair.

[@alz722]

What propper tool?

[@twowheelsonelove4040]

I replaced it exacly as it said here but now car wont start...

[@sandyande]

Petrol or diesel?

[@twowheelsonelove4040]

Diesel 320d

[@sandyande]

Are u getting RPM reading on tachometer/rev counter when u crank it over?

[@twowheelsonelove4040]

Yes the rod lifts a little bit above the 0 in spidometer when i try to crank it

[@NG-zg8vf]

How would crank pulley affect the car starting?

[@marijabosnjak1421]

you talk very quickly about slow actions in the work phases and your English is unclear and bad ...

[@sandyande]

Hello, English is not my first language it's broad Scots!!! Cheers sandy