Thanks Chalieoscar, we hope you can take something from this video, thanks for watching and glad you enjoyed it.🙌 Manual Choke is also a valuable tool in the tuning proces and with fuel diagnostics. Use it as it saves time.
@Sillsii5 ай бұрын
5:05 doesn't it need power to adjust itself? how does it get power while in the freezer?
@scooterstreetau5 ай бұрын
It works on temperature and changes position based on the temp of the sensor inside the mechanism. The power adds heat so it can expand to closed position. It does not need power to retract, so we put it in the freezer to speed up the activation process.
@Sillsii5 ай бұрын
@@scooterstreetau oh I thought it expanded via power or something, I was tired sorry. Thanks a lot for the clarification!! :)
@scooterstreetau5 ай бұрын
@@Sillsii All good, thanks for watching and comments👍
@ClydeSlobbs3 ай бұрын
how does it turn itself off?
@scooterstreetau3 ай бұрын
@@ClydeSlobbs It works on temperature and changes position based on the temp of the sensor inside the mechanism. The power adds heat so it can expand to closed position. Watch the video, it is discussed in detail.
@balamood6183Ай бұрын
If i were to plug the e choke out, the cable that goes to it. Would it be like running the bike completely warmed up but all the time? And also if i were to plug it out when the bike is completely cold and the ignition off would the choke be off and completely down?
@scooterstreetauАй бұрын
Physically check the choke position, move to the manual choke.
@Donbscooters757Ай бұрын
Is this for 2 stroke and 4 stroke scooters ? My scooter hard start unless i unplug the inricher then will start. And have problems idle. . it didn't used to do this .
@scooterstreetauАй бұрын
The auto choke system is the same for all types, it is a system which enrichens the fuel supply, the choke may look different but operates under the same principle.
@twostrokegarage9 ай бұрын
hello, i have a "small" problem. recently i gave my scooter a bit of a makeover, put a new exhaust on, rejet, new rollers and springs. but now when i use the throttle the bike takes a very long time to accelerate, like i have to rev it to above 5k rpm before it even moves a little, and acceleration is just painfully slow. i thought it might have ti do with to stiff clutch springs or something wrong with rollers. on unrelated note there has also been a rattling sound coming from the variator like a screw is loose in there or something. scooter in question is a derbi Atlantis with hiper engine. any help appreciated and cheers💪
@scooterstreetau9 ай бұрын
Remove the parts one by one and start with the springs.
@R_O_B_O_M_A_N2 ай бұрын
did u figure it out? i have a derbi atlantis 2T , its a great scoot but i have had to fix every imaginable troubles.
@twostrokegarage2 ай бұрын
@@R_O_B_O_M_A_NSlow acc was from me still having restrictor in the exhaust. Also changed to lighter rollers. The rattle is still there, and is coming from something loose with the kickstarter, most likely the pinion gear. Flat rollers could also be the problem. Easiest way to tell would be to remove the variator cover and start the scooter without it, that way you can see if its kick or vario issue.
@balamood6183Ай бұрын
Is it ok to drive with the choke plugged out? The cable that goes to it. Would it harm the scooter in any way?
@scooterstreetauАй бұрын
Will be no problem.
@woody11619 ай бұрын
Hello, ive got a jetforce 50 with a 70cc malossi kit in, 8g rollers and leo vince clutch springs, uprated carb and a leo vince tt exhaust but i can only get about 45mph out of it, any advice. Thanks
@spicychickennugget32409 ай бұрын
Try getting a over range variator for that extra gearing?
@scooterstreetau9 ай бұрын
is everything derestricted? Upgrade the cylinder and exhaust.
@Ace010109 ай бұрын
Will it work with any carb? I have a honda Dio AF18 and the E choke has a faulty connection. One of these seems like a perfect replacement, especially for cold starting. Question though? How long do you usually let the choke stay on for the manual one?
@scooterstreetau9 ай бұрын
Yes it will, leave it on for 10 seconds and as you slowly start to turn it off apply a touch of throttle.
@Ace010109 ай бұрын
@@scooterstreetau Alright so I got the choke and bike still won't start, gas is cycling to the carb. Am i missing something?
@scooterstreetau9 ай бұрын
Check the air filter, enough air flow? Check the fuel flow when cranking the engine, is the fuel flowing to the carby? Check for spark, is it Zapping Blue/white at least 10mm? Test compression and air leaks.@@Ace01010
@SryFoolАй бұрын
Could my choke be the issue? Basically when cold it stalls when no throttle input and it runs very rich when cold, once warmed up it runs perfect
@scooterstreetauАй бұрын
Yes it may be. Check and test it as in the video.
@SryFoolАй бұрын
@scooterstreetau unfortunately it was not the e choke, it works as intended
@NickGarmАй бұрын
Very helpful video - thank you!
@scooterstreetauАй бұрын
@@NickGarm Thanks for watching = support👍
@gabrielwalker4212 ай бұрын
my Gilera DNA 180 starts immediately from fully hot or fully cold but needs a bit of throttle to start up when its hot but been off for a few mins. It fast idles cold, idles like shit for a few seconds then fast idles again gradually settling into its idle. When started from warm but not fully hot it needs little bit of throttle to start, idles rough for a couple sec, fast idles at like 2k rpm for 30 sec or so then back down to set idle. Closed idle mixture screw causes engine to eventually die so ik pilot jet is fine and the throttle response is fantastic. I read that these auto chokes have 'wax capsule' in them which expands with heat to push the plunger out. Can this deteriorate over time and how well protected is it against chemicals like fuel, carb cleaner/non-polar solvents etc. Like the choke obviously works but I dont think its as responsive as it once was (2ndhand unit from ebay as i need OEM) or is sticking a bit. Also I'm actually really surprised at how much electrical shit does actually deteriorate gradually rather than it either works or it doesnt and it seems to be a big thing with 'solenoid' stuff like this.
@scooterstreetau2 ай бұрын
Go the manual choke system, it eliminates any guessing so you can get down to the true issue.
@gabrielwalker4212 ай бұрын
@@scooterstreetau do all auto chokes have wax in them?
@scooterstreetau2 ай бұрын
@@gabrielwalker421 no
@usfsft62172 ай бұрын
Hello! I have an issue with my scooter but it only happens once every 5 rides approximately , so what happens is after about 1min of me riding it sputters and dies . Only way I managed to to start it back on is by closing off the air pipe to the filter and it revs for 5sec before dying down again. I looked basically into everything (air filter, carb,idle mixture,fuel lines , valve adjustment , fuel filter , spark plug ,changed cylinder , checked vacuum lines) only thing I noticed is the air intake hose to the carburetor having a small crack . I had the scooter sitting for abt a month in the sun could it have caused something to go bad in the CDI or this auto choke?
@scooterstreetau2 ай бұрын
Change the manifold if it has damage.
@usfsft62172 ай бұрын
@@scooterstreetau not the manifold, I meant the part that connects to the carburetor not the one that goes to the engine
@scooterstreetau2 ай бұрын
@@usfsft6217 Change the broken parts, they are not designed to work in a broken state.
@ScooterMods2 ай бұрын
Do you have the link for this choke your displaying?
What should the voltage to the choke be? When i tun my starter its 4v in the contact.
@scooterstreetau9 ай бұрын
I just had an opportunity to test the choke on a 2 stroke, the power is AC and put out 4.6 volts. Ignition on no power, it is only powered when the enigne is running. Power supply when the stator rotates.
@marenjensine24682 ай бұрын
My choke only move 2 mm, is it possible to repair ? A new in DK cost 110 aud
@scooterstreetau2 ай бұрын
Replace with Manual choke, is cheaper.
@369HZX3 ай бұрын
Hello! I've only get 3V from the wiring. Aprillia sr50 2019. New choke = same problem. Anyone know where that 12V is sourced from in the electrical system? I have ordered the manual choke, but would be nice to get the electric choke to work as well
@scooterstreetau3 ай бұрын
3V is what is required to run the choke.
@369HZX3 ай бұрын
@@scooterstreetau It's not working for me. I swapped to manual choke.
@iaincreer87605 ай бұрын
Are these auto chokes generally the same thing? I would like to convert my Peugeot Django 125 to a cable operated manual choke. Do you think yours would fit?
@scooterstreetau5 ай бұрын
Find out what type and size of choke and you will possibly find there is an option for manual choke.
@ropi99929 ай бұрын
Heloo, what spark plug do you recommend for stage 6 mk2 racing?
@scooterstreetau9 ай бұрын
We use BR9ES for ZIP.
@GY6ScooterAdventures-be2oe7 ай бұрын
Thanks for this very informative video! I have a new scooter under 400 km. It seems to run good but before starting it, I usually need to turn the throttle once and start it up. The rpm is only about 1,000 to 1,500 rpm's so I have to baby the throttle a few minutes (or it will stall out) until it starts ideling at around 2,000 to 2,500 rpm's and then it's fine. Do you think it could be the auto choke is not working?? Thank you
@scooterstreetau7 ай бұрын
Check the choke for sure, also the cary may not be adjusted correctly and also you may have an air leak so check from the airbox to the manifold just to be sure. this should be done from the dealer at the workshop prior to delivery to customer so if you have an issue reach out to the selling Dealer👍
@GY6ScooterAdventures-be2oe7 ай бұрын
@@scooterstreetau Oh, its a Carburetor
@scooterstreetau7 ай бұрын
@@GY6ScooterAdventures-be2oe see reply above
@GY6ScooterAdventures-be2oe7 ай бұрын
@@scooterstreetau Thank you very much 👍
@faw25622 ай бұрын
Hey so my Aprilia SR50 starts first kick in the morning and it starts off with high rpms and drops after a few seconds but if I let it idle for 2mins it dies. Also when i start riding the throttle response is poor and sputter before taking off even when its warm. Could it be a choke issue?
@scooterstreetau2 ай бұрын
Yes, It could be a choke issue, or a spark issue, or a plug issue, or an air issue.
@TheUtube4mikeАй бұрын
I added some 10W40 to the inlet of the carb and it lubed the choke. Ran the moped around the block twice and it runs well now. I was not able to remove the 2 screws that hold the choke to the carb. Good video, I learned everything I know about auto-chokes from this video.
@scooterstreetauАй бұрын
Great to hear👍👍
@Fatback135 ай бұрын
Dumb question but i need to ask, can choke be fixed somehow becouse in my country the only option is 200eur for keihin cvk18 just the choke :(
@scooterstreetau5 ай бұрын
You can't fix the auto choke, but you can modify it it to work as a manual choke.
@yajibun92206 ай бұрын
Hey man! Do you have any idea why my 50cc yamaha scooter runs so good when cold for like 2-4mins and then it starts to lose power and can barely go up a hill and atleast 50% off acceleration speed just disappears. The problem has worsened when summer came
@yajibun92206 ай бұрын
You didnt answer but i think it was the air filter because when i changed it the scooter worked way better
@threefootflatty368810 ай бұрын
hi mate i’ve been having problems with my moped recently. so i found out i had a split in my fuel line and i needed to fix that immediately, so i ended up replacing them and since then it started bogging out after half throttle and just seemed like it was struggling. i rode it for a few days after that and on thursday last week i was going home and it just randomly started sounding like a piece of metal in a washing machine, just grinding and jolting and struggling to run. i don’t know what’s wrong with it
@scooterstreetau10 ай бұрын
That makes 2 of us. Check out the source of the noise.
@threefootflatty368810 ай бұрын
@@scooterstreetau it’s hard to tell when it’s coming from since it only happens when i ride, but i think it’s coming from the cvt. i took it apart and noticed who ever owned it last, the plastic variator fan snapped and they never replaced it. it’s a piaggio zip 2t
@scooterstreetau10 ай бұрын
Why not have a look.... Running the engine without a fan will without a doubt casue a major engine failure.@@threefootflatty3688
@threefootflatty368810 ай бұрын
@@scooterstreetau okay no worries i don’t know if it broke while i was riding it or if was like that a few months ago before i bought it, but what issues could it cause without having it?
@scooterstreetau10 ай бұрын
Over heating of the transmission.@@threefootflatty3688
@ArthVader097 ай бұрын
My gy6 starts fine but every stop it drops rpm and when you rev it 2-3 times it will go back to normal. Is it auto choke always turning on every stop?
@scooterstreetau7 ай бұрын
Check for air leaks in every rubber part.
@namaikativputkata2023 ай бұрын
i have the same problem any solutions? pls
@ArthVader093 ай бұрын
@@namaikativputkata202 i just raise my idle screw so that if it drops rpm, it will still be sufficient and not sound like struggling. I dont have any vacuum lines leaks at all
@DonDinero942 ай бұрын
@@namaikativputkata202any luck? I have the same problem I had to raise my idle screw to the point the scooter wants to move while I’m on it
@namaikativputkata2022 ай бұрын
@@DonDinero94 i bought manual choke and all the problems gone away try it
@js256scoast9 ай бұрын
Hey guys, im experiencing splutter/bog at 3/4 throttle, wondering what your thoughts would be. my set up: Piaggio zip euro2 50cc 2t Stage 6 exhaust MHR replica 70cc kit 5.5 gram rollers 82 main jet
@scooterstreetau9 ай бұрын
You need to eliminate the possible cause. Do this by testing each system, Jet up to 98 and come down from there. Is the needle set to middle. You should only fit 1 part per time and tune to suit to avoid this. It will save dollars and hours of trouble shooting.
@js256scoast9 ай бұрын
yes I did change one part at a time, however the splutter/bog has been pretty consistent. The clip was initially on the leanest top notch so I moved it to the middle which helped somewhat in the mid range but still the same issue from half throttle onwards@@scooterstreetau
@scooterstreetau9 ай бұрын
What did you do or change when the issue first presented?@@js256scoast
@js256scoast9 ай бұрын
I went from a 82 main jet to a 78 main jet with not much change.@@scooterstreetau
@js256scoast9 ай бұрын
I went from an 82 main jet to 78 main jet but it didn't change much@@scooterstreetau
@black63ford6 ай бұрын
This is a very informative video. I now know how this works. Is this available in the USA.
@scooterstreetau6 ай бұрын
Thank you, yes it would be available in the USA. Search local scooter part suppliers.
@chrisdeegenaars11685 ай бұрын
Where are you located and what does a manual choke cost
@scooterstreetau5 ай бұрын
Gold Coast, approx. $25.
@fraserm8034 ай бұрын
Dont quite understand....if there is no "spike" on the manual choke how does it block the carb hole.
@scooterstreetau4 ай бұрын
The rubber seal does the job of blocking, the spike does the locating.
@paulbudford10 ай бұрын
I've never heard of putting them in the freezer. Every day's a school day. 👌
@scooterstreetau10 ай бұрын
Just like a beer , better icy cold.
@magamen65727 ай бұрын
My choke keeps falling out of my scootstar racestar 50cc theres no way to hold it in the fixings are missing i brought this brand new as well
@scooterstreetau7 ай бұрын
Ask the selling Dealer for assistance.
@MasonBurroughs-k4g2 ай бұрын
Do you have Genuine scooters there? P.G.O is another name for them. I have a 2008 buddy 50. I put a Amazon big bore kit on. Kit was ACTUALLY decent quality for $ I chamfered the inside of ports etc....bike locked up like 10times on way to store & back from running lean. Obviously I have a Massive air leak somewhere correct? Idk how I didn't melt the piston😬😓💯
@scooterstreetau2 ай бұрын
Genuine and Buddy are the American renamed PGO brand scooters. Was the engine setup for the BBK?
@MegaSafetyFirst7 ай бұрын
Big thank you for this great explanation!!! Showing the different scenarios at the end really helped 👍👍
@scooterstreetau7 ай бұрын
Thanks heaps, glad we could help you🙌
@123Ansido-uf1nv6 ай бұрын
I changed the auto choke with a brand new one and it works but not as it shoulds
@scooterstreetau6 ай бұрын
Thiat would be confusing, check the choke and check the carb settings, you may have anther issue.
@WillemVanheerden-q8j6 ай бұрын
Hi my carburater don't give petrol to the spark plug
@scooterstreetau6 ай бұрын
Oh no..
@TheBarrynorth7 ай бұрын
Agreed - great video - straight forward - applied it to my typhoon and all now seems fine - thanks
@scooterstreetau7 ай бұрын
Thanks Barry, as simple as it is this is one of our most valuable videos in terms of self diagnosing these issues and determing how to resolve.
@daveanderniesmotorizedbike13559 ай бұрын
The first thing you would check and see if you have power to the choke!!! And if not how to fix the hot wire!!!!
@scooterstreetau9 ай бұрын
Yes good addition to the troublesome choke. We remove the choke and have a special connection which connects it directly to a 12v battery, you can visually see the choke extend into the OFF position. Or the freezer to have it retract.
@Donbscooters757Ай бұрын
Im going to convert to manual choke try to do it tomorrow see what happens
@scooterstreetauАй бұрын
Ok, ensure a good seal at the choke/carby.
@shuddhodhanshetty58397 ай бұрын
Beautiful explanation of electronic choke working❤❤. Thanks a ton.. Helped me diagnose the issue with my scooter too! 😊
@scooterstreetau7 ай бұрын
👋 So glad to hear! The purpose of our video. The help we needed when we were younger.
@coleEmmm96Ай бұрын
No icecream in the scooter street freezer only auto chokes,cranks & bearings
@scooterstreetauАй бұрын
😂Ice creams fill the freezer once a month.
@charlesdao4000Ай бұрын
the electric automatic choke turn to Human Choke ^^ !