Scooter/ motorcycle/ Atv / Moped gy6 150cc carburetor Overview

Carburetor for Gy6 150cc price is around $30.00
click here == amzn.to/2y7tqBc
Donate to Virberello for Parts rb.gy/gzrtit
Chinese Scooter Service Manual amzn.to/2LBfWb8
Scooter/ motorcycle/ Atv / Moped gy6 150cc carburetor Overview
Industry Standard: Japan standard
Carburetor Model Number: PD24J
Material: Aluminum /Zinc
Weight:28.2 ounces
Manifold intake diameter: 24m,outter diameter:32mm
Jet size: 5mm*height 8mm
Air filter interface outside diameter: 42mm
Easy Adjustment,Accurate Control
1 Idle Screw: clockwise for fast idle,counterclockwise for slow idle
2 Air Mixture Screw: clockwise for less air,counterclockwise for more air
3 Drain Screw
This are many brands of scooter that need this carburetor
BMS 150, Znen 150, ​Tank 150, Sunl 150, Vento 150, Kandi 150
Retro 150, Manco 150, Helix 150, Jonway 150, Shenke 150,
Zircon 150, Roketa 150, Hensim 150, Qingqi 150, Kinroad 150
Kinroad 150, Carbide 150, Quantum 150, Baja 125 150
Eaglecraft 150, Eton Yukon 150, Coolster 3150DX2
Dazon Raider 150, Carter Talon 150, Lance Vintage 150
Taotao 125 150 4 stroke, American Sportworks 150
​Tomerlin Crossfire 150 150R, Kymco Agility125 150 4 stroke
Hammerhead GTS 150 Hammerhead Twister 150
Genuine 125cc 150 such as Buddy 125 Trailmaster 150 XRS XRX
Yerfdog GX150 Spiderbox 150cc such as 3206/4206, 3209/4209, 32092/42092, 32093/4209, 42054, 42094, 42101, 42105 RidgerRunner II, and other unlisted 4 stroke GY6 125cc 150cc engine
Thank you for watching my video I hope you enjoyed

[@dentalflesh677]

You are awesome!!! Love your videos!!! Thank you for being so detailed and caring!!! Have a wonderful Year!!!

[@VirberelloScooterTips]

Hello Eric thank you very much for watching my videos and have a great new year

[@shopsteward6292]

Love your dialect, great video

[@VirberelloScooterTips]

Hello Carl thank you for watching my video

[@sus8e462]

The cross section was great & the illustrations of the air & gas flow! But the stock sizes for jets isn't the same as in another video you have about tuning--in this you say 35 & 108 or 110, but another video you list 32 & 75 as stock.... Also would be great to clarify it this is a slide carb or CV type (2 or 4 stroke engine)!

[@servantoftheservant5022]

Thank u Virberello my scooter is no longer cutting out when i have the throttle fully opened cleaned the carb.. smaller petrol filter but still cant go faster than 60 km southafrica

[@VirberelloScooterTips]

Hello servant of the servant great news very happy for you my friend thank you for watching my video and be safe

[@kennethgrimes5494]

sir you are the best at teaching on the net thank you sir

[@VirberelloScooterTips]

Hello Kenneth thank you for watching my video

[@capnchip]

THANK YOU SO MUCH!!!

[@VirberelloScooterTips]

Thank you for watching my video

[@andyproctor3588]

Hey my Florida friend enjoy this video me being up here in North Florida gets a little chilly every now and then kind of helps me on my idea of having to readjust my carb thank you as always and waving my hand from Gainesville👍

[@VirberelloScooterTips]

Hello my friend Andy Down here keeps rain everyday no stop I hope the new year will bring the sunshine back Thank you for watching my video my friend have a great Holiday season and a fantastic new year

[@arthurwoodhouse4347]

Thanks so much! Brilliant video with useful details, really saved the day!

[@VirberelloScooterTips]

Thank you for watching my video

[@aA-lg1se]

Thanks for your video can you tel me please how to set gass and air mixture

[@VirberelloScooterTips]

Hello to set gas and air mixture you need to tight the little screw that is on the left side of your carburetor all the way in and them back up the screw 3 quarter turn Thank you for watching my video

[@Brancaalice]

Hello, i have a new scooter and the hear trunk lid does not fit well, there a way to fix it? It not aligned, only when i lock it. any advice what to do.

[@VirberelloScooterTips]

Hello my friend you could buy a Locking Latch amzn.to/3A3RlEX. Thank you for watching my video

[@derekmaxwell8164]

What cause the carb to flood engine over rough terrain? On pavement my gy6 kart runs excellent except if i slam a curve real hard or hit rough terrain. If i shake the carb side to side by hand fast it will cut out too so i know its not wiring issue

[@VirberelloScooterTips]

Hello Derek you need to inspect the carburator could be the float valve needle or the float that is demage and is not closing the fuel flow . Thank you for watching my video

[@Mr.Riffian]

Does the automatic choke keep drawing current at a permanent basis or cuts off once the engine warms up?

[@VirberelloScooterTips]

Hello my friend the automatic choke keeps drawing ac current from the stator when scooter is on

[@warrawechaboonsa728]

Hi, how are you? I just bought the carburator. I wonder what if we do not connect the auto choke. I have the old Atv. Just try to tebuild it. Thank you very much.

[@VirberelloScooterTips]

Hello my friend if you do not connected the enricher your scooter always be at higher rpm but if you connect the enricher the plunger will close the extra flow of fiuel but you can always buy a chocker conversion kit for 24 mm carburetor

[@warrawechaboonsa728]

Thank you. To connect the enricher, can we just supply 12v from a battery or else? Thank again.

[@elvatotoro]

Can you help me ? I have a similar carburetor but there are more vacuum inlets and I’m not sure where to connect to what

[@VirberelloScooterTips]

Hello is the carburetor for a gy6 150cc ?

[@elvatotoro]

virberello GY6 Scooter Tips I believe it is. It’s of a Chinese dune buggy but it almost exactly I denticle but it has a few more inlets on the side and I was trying to see which are vaccine and which are just open. Thank you !

[@elvatotoro]

virberello GY6 Scooter Tips is there a way I can send you pictures by any chance?

[@gevoorot]

Can the smaller idle jet be poked through with one of those motorcycle needle tools to clean the passages or is the hole too small on the jet to use that tool?

[@gevoorot]

I've tried to poke it through with the smallest needle, but it just won't go through. Any suggestions???

[@rickbaye8296]

I really enjoyed your explanation of how the carburetor works. I have a question. I've replaced the carburetor and auto enricher but I have a problem. To get my motor to idle at startup, I have to adjust the idle screw to increase the rpm's. After the motor warms up, around 2 minutes, the rpm's increase and the idle is too fast. I thought the idle is supposed to go down after the auto enricher is fully extended. I have the exact opposite happening with my motor. Can you help me please? I have all of the different sizes for the main jets as well as the idle jets. Could changing them fix my problem?

[@VirberelloScooterTips]

Hello Rick Yes you completely right idle is supposed to go down after the auto enricher is fully extended but did you take the enricher out and test that to make sure is working properly you need to get a reading of 11 to 23 ohms on a multimeter that is the first thing that comes to my mind second I will check the voltage that goes to the enricher should be from 11.5 to 12.3 volts from the alternator your main jet should not be a problem but I will keep a 107 to maximum of 115 main jet just for testing but that I don't think is the problem, check if the pilot jet inside the carburator is clean spray some carburetor cleaner everywhere in all the jets also in the all of the enricher and last make sure that the vacuum line that goes to the top of your carburator is connected and the rubber is not broken. I hope this can help you but don't give up until you find the problem. Thank you for watching my video

[@clintoncrockett773]

Hello. My carburetor for my GY6 Scooter has a Dummy vacuum port on the Right side of the carburetor. The tube for the vacuum hose is sealed and under the plate there is no holes for for a vacuum. I have changed the petcock to an On and Off switch and do not see a need for the vacuum hose. Do you have any advice on this situation? Thanks! Clint

[@VirberelloScooterTips]

Hello Clint in the port on the top right you should have a little diaphragm that help the carburetor but if you do not have anything look like your scooter works better without that so plug the nipple at the manifold and test your scooter after you place a new fuel line. Thank you for watching my video

[@LumocolorARTnr1319]

Nice video, high detail. Thank you!

[@VirberelloScooterTips]

Thank you for watching my video

[@salmanfaizee5816]

Is the carburetor need 12v direct power supply? I have a bike with old carburetor but I want to replace that with gy6 carburetor but don't know how to deal with the automatic choke power. So is there any solution?

[@VirberelloScooterTips]

Hello the carburetor automatic choke get the power 12v from the stator so if you like you can get the power from your alternator check this video kzbin.info/www/bejne/nZupfY2Epr1sbaM

[@ashberger6334]

Hi I just changed my carb out since the stock one was sealed. I put in 115/38 jets. Tried to start it and it started but then died. I changed the jets to 110/35 and it started up. Rode it around for a few mins, turned it off. But then it had difficulty starting again. Any ideas what could be wrong? 169cc, live at sea level

[@ashberger6334]

Oh and I changed the exhaust to a short exhaust if that matters, also took off stock air box and put in a pod filter

[@texxmex266]

i have new carburator in scooter but it will not start. how does gas enter the bowl of the carburataor?

[@VirberelloScooterTips]

Hello Rudy the fuel enter the carburetor from the little plug valve that is under the floater inside the bowl . Thank you for watching my video

[@texxmex266]

@@VirberelloScooterTips sorry I know that I have my line connected and have verified the line is working properly. I have tried starting it multiple times but will not start. How long does it take for carburetor to fill enough to start engine? Ty for your quick response

[@VirberelloScooterTips]

@@texxmex266 Hello Rudy it does not take to long to fill up the carburetor bowl around 1 to 2 minutes did you do a fuel valve petcock test kzbin.info/www/bejne/ramzo3WFbtaFjMk to make sure your fuel flow free from the tank to the carburetor did you check the vacuum line and make sure is connected with the manifold

[@VirberelloScooterTips]

is that a standard carburetor ? because sometime when you a racing carburetor they come with no jets

[@texxmex266]

@@VirberelloScooterTips www.amazon.com/gp/product/B00SUT2UVA/ref=ppx_yo_dt_b_asin_title_o05_s02?ie=UTF8&psc=1

[@markyj07]

Hi, the part mentioned at 2:30 that connects to the vacuum line to the manifold with a small diaphragm inside, on mine I took that part off when cleaning out the carb and I was unable to blow through the elbow of the tube that comes off (the whole metal cap part with the L bend on it). I was unsure what this part was supposed to be doing, hence why I found and watched your video. My question is, how tight is the gap here, should I be able to blow through it myself (human breath strength) or is it so tight that only the engine forces would affect it. The reason I was cleaning out my carb is because I have been having issues with a cold start and staying on idle. To start I have to really throttle it and then keep the revs up or it will die on idle. I'm no mechanic but have fixed a few things on my bike now. Thanks

[@alsehendo34]

I wondered the same thing my original carb on Aldy 150 has a diaphragm in there the new Amazon carb does not.

[@edgarsanchez8537]

I have a question my four wheeler has gas in the motor

[@steffenkieslich4573]

Thank you for this great video. Liked and subscribed.

[@VirberelloScooterTips]

Thank you for watching my video

[@markpaulson2720]

Thanks so much for showing me how to

[@salimdeveci]

Hi first tanku very much i have ask for you .one side of a wing of the carburetor float is broken.Does this work?thanks for your reply

[@VirberelloScooterTips]

Hello if your float is broken you will need to replace that, you can find a carburetor rebuild kit or just buy a new carburetor. Thank you for watching my video

[@Mk-et9fj]

How far in is the ideal screw supposed to b ?

[@VirberelloScooterTips]

Hello MK On most 150cc scooters, idle speed should be around 1500rpm when the engine is fully warmed up. Don't make adjustments when the engine is cold. Take a 5 or 10 minute ride first but more or less is 3.5 turns in but sometime in some carburetors that can change. Thank you for watching my video

[@betoaguilera2077]

perfect video you helpme a lot

[@VirberelloScooterTips]

Thank you for watching my video

[@alsehendo34]

I took off the vacume diafrmm and forgot how to put it back. Can somone explain?

[@VirberelloScooterTips]

Hello Stephen look this video at 15:28

[@alsehendo34]

@@VirberelloScooterTips I mean that thing on the side with two screws and a 1/2 inch diapfame under it and a hose nipple sticking up. It hooks to engine vacume, but I realy dont know what it dose? It's on same side ac throttle linkage.

[@alsehendo34]

@@VirberelloScooterTips you can see the thing @ 1:45 on the side.

[@alsehendo34]

@@VirberelloScooterTips you say its vacume to open needle in carb. Wish I could see a video that some one removed those two screws an put it back together under there. THANKS

[@tombramogrodzeniakute8815]

How size jet for 107 ccm

[@VirberelloScooterTips]

Hello Tom not to familiar with 107cc but should be a 95-110 main jet if you live at higher altitude you go down in size. Thank you for watching my video

[@danbuck7877]

Lo

[@peterroque3933]

PATHETIC