Scratch From Key-Reapair Without Painting

[@angelcolon2026]

Looks amazing. Thanks for the upload

[@Amddetailing]

Tnx and enjoy

[@conordoherty1864]

Great to see an upload from you again

[@Amddetailing]

Tnx

[@moonc4lf]

Tim klošarima što grebu aute ključevima treba lomit ruke javno nasred trga.. svaka čast na poslu 👌

[@Amddetailing]

Dzaba toga uvijek ima

[@darrenmetal3338]

Keep uploading these amazing vids please. I've learned so much already. Your skills are from another level as it seems

[@Amddetailing]

Tnx my friend

[@chrissimon8403]

Great work from a professional!!

[@Amddetailing]

Tnx

[@mnap89]

You can see the scratch becasue applied paint is softer then what is on panel. So when you sand it down smooth, you will remove "new" paint quicker during polishing becasue it is softer. In good light and viewing angle you can see how light reflects in the groove. Anyway - its a good job, and much better than having scratched car and cheaper than paining whole panels.

[@mkprodetail8714]

Brilliant work. Very well explained. Saved the customer a fortune. We have learned loads from you. We even purchased a uv scangrip lamp and uv lacquer after 1 of your videos. Well done, keep the videos coming

[@Amddetailing]

I am glad that you are another one of my followers who have been helped by my videos keep it up

[@Tonino59]

Lo ripeto ancora, sei molto ma molto bravo, immagino quanti anni di esperienza hai per questi risultati eccellenti. Ti abbraccio fratello, Saluti dall'Italia

[@OZIO84]

You are the best!👏😲💪

[@bradymorse8848]

Another great job!

[@Amddetailing]

Tnx

[@Mr.johansson]

Great job master Alan ..you are 👑

[@Amddetailing]

Tnx my friend

[@yeungkawo]

Your video is great , very informative , Thanks!!!

[@gbitpal]

Link to the needle paint tool plz.

[@Amddetailing]

Tnx bro

[@SLYDIT]

Use a tungsten block to cut bach the paint initially. Theyre specifically designed to knock back paint runs without taking off so much clear around it

[@Super-lucky-7777]

Subscribed to learn more

[@Amddetailing]

Tnx my friend and enjoy

[@user-uk5qk1zo4k]

Clean job 🖖🖖🖖🖖🖖

[@Amddetailing]

tnx bro ad enjoy

[@admir1943]

Doktor 👊💪☝️🥇🏆

[@Amddetailing]

😘😘😘

[@RakicFarbanjeKlavijatura]

Nema boljeg majstora za poliranje! Svaka cast! Nema te nesto u grupi Lakiranja na fb? 😀

[@Amddetailing]

Heheh hvala ti ,a nemam vremena iskreno zavrsavam obuku za PDR pa sam slabo aktivan

[@RakicFarbanjeKlavijatura]

@@Amddetailing primetio sam alat na zidu.. super, jedva cekamo snimke i za to 😀

[@Amddetailing]

@@RakicFarbanjeKlavijatura da uzeo sam nesto od alata i zavrsavam tu obuku pa cu gledati i to predstavljati na kanalu da olaksam ljudima kojibse mislie ovim baviti

[@rob061883]

Wowww awesome I wish you were close by me

[@Amddetailing]

Tnx my friend

[@carlifegarage2340]

Where do you buy acrylic lacquer basecoat?

[@mrBDeye]

This is the notorious deep key scratch caused by cheating lovers or hateful neighbors. Sometimes this damage is done to the wrong car.

[@Amddetailing]

Hehehhee

[@fraizer2600]

super work but can you please explain us why this time you dont use the Micra yellow scrap tool ? you use directly and only sand paper. thank you for your answer :)

[@alisomji3294]

Yeah, I like to know the same

[@Amddetailing]

it is explained in the video that it turned out to be much better to remove the filled case with water paper when it is done

[@fraizer2600]

@@Amddetailing can you please explain for what reason is better ? I dont notice an explanation in the video why scraping with micra is less good in comparaison of wet sanding :)

[@Amddetailing]

When the lines are shallow and thin, the Mirka scraper knows how to take out the color you filled and you have to repeat everything, Mirka is a good thing and I use it, but when the lines are wide and there is more material to sand

[@fraizer2600]

@@Amddetailing when the ligne are more deeper with more material to put the risk to use a Micra scraper can remove the paint ? This why you use sand paper ? Thank you ;)

[@zzo28]

Why did you not use Mirka Stain File but sandpaper to paint leveling ?

[@pcdetail602]

Great video.. what's the ratio on the mixing of hardener and paint and clear all together ?

[@markosokcevic3209]

Omjer laka i hertera 1:1, a koji je omjer baze i njih, isto 1:1? Video je super

[@JaguarPaw1]

Great job can I do this with spray paint from a can?

[@Amddetailing]

you can't spray

[@tumypavel]

Great result. I have an touareg also with same damage on fender and i want to do it by myself. Because your videos i start to polish/repair my cars and buy a lot of staff for it 😅 I have some problems in purchase the paint. What should i buy? 1k or 2k paint?i need to use thinner? Thank you!

[@Amddetailing]

the base is used 2k, it is diluted with an acrylic thinner, if you use an acrylic base, then the absorbent goes into it and that's it

[@tumypavel]

Thank you!

[@ramazangunes3599]

What is the professor dye mixing ratio

[@calimeroBiH]

Odličan posao odrađen. Radiš li lakiranje komplet branika ili samo parcijalne ispravke ovakve vrste? Pozz

[@Amddetailing]

Hvala ti,ne bavim se lakiranjem

[@Lfm599]

very good job you mix the base with the varnish directly?

[@matteomontagna7760]

I'm curious to know too

[@Amddetailing]

Yes

[@LordAleksey]

I have a same problem with more difficult paint condition (17yrs old paint), when i polish it some of clear coat going bad, i think cant do same repairing job like the video

[@DetailingTurzovka]

Hello. Very nice vid. I use 1 part base 1 part clear 1 part quick hardener Most of the times i cant fill the scratch fully on 1st go. When it dries, i can see how the color settled down. I'm applying maximum amount. If i add more, it would spill. The paint is thin after some time on the open. Shall i wait longer for thicker substance? Thank you :)

[@Amddetailing]

It is always filled thicker, from the first time, it is never directly touched to the damage, when the paint is applied to the damage, you have to remove a few millimeters and let the paint fill it by itself. I always leave it to dry for at least 4 to 6 hours

[@DatBoi-mz7pp]

Nice upload as always! One question, why didn't you used the UV Clear Coat this time? I've noticed the repairs with the UV Clear are usually better than with standard clear and hardner combo. Cheers

[@apollo5751]

I've tried locating UV cured clear in the USA to no avail. I've asked major suppliers personally, nope.

[@Amddetailing]

I could do with that too, but since it's currently autumn and there's less sun, it's immediately more difficult to dry with a UV coating, and it takes a long time to dry with a lamp because the damage is quantitatively large

[@Jopakilo]

Looking for Pdr on door edge

[@user-pg5ln2yj1q]

This is Korea. I want to learn the skills of the teacher. What should I do? Please teach me.

[@Amddetailing]

You have a lot of videos on my channel and in each one it is explained how to do what

[@user-pg5ln2yj1q]

@@Amddetailing Thank you for

[@ForEvolution]

why no clearcoat ?

[@Amddetailing]

everything is mixed together, follow the video carefully, everything is explained in it

[@chitotanada1389]

how much do you charge for this kind of job?

[@Amddetailing]

400 euro

[@e630fnr]

@@Amddetailing Roughly about the same money would cost to paint the two doors and fenders in Greece where I live.

[@Amddetailing]

it's not a problem, the problem is that people don't want to paint the entire element and spoil the factory coating, because later they have a problem when the car is sold, because more and more customers think that the car was in a big accident as soon as it was painted. Put yourself in a situation when you are buying a car and you see that something has been painted, you immediately have doubts and avoid such a car.

[@Bull1the1Great]

Sto znaci PDR ? ( X DENT REMOVAL ) . Tata mata ko i uvijek

[@Amddetailing]

Paintlless Dent Removal ili uklanjanje udubljenja bez farbanja

[@Dagadaga1]

Vi ste rođeni na balkanu haha ?

[@Amddetailing]

Da sto

[@Dagadaga1]

@@Amddetailing negdje sam vidio komentar na nasem jeziku pa gledam jel translate ili hahahaha

[@rob061883]

Do you have an email address I would like some advice I have with my Honda odyssey ?

[@Amddetailing]

Yes [e-mail] or fb page Alen Tataragic

[@chops6474]

Kudos for trying, but this really needs 320g, sealer, blender, 2BC, 1 orientation, 3 CC to look right. The scratches are extremely obvious and jump out. Cheers

[@irollon26s]

@@chops6474 what’s all that?

[@Amddetailing]

yes, it can be seen from 5 centimeters from the car and it looks like a scratch made of wood and because that side is polished and there are no scratches on the coating caused by washing and the color is refreshed, but after a few washes it will all blend together and not be noticeable

[@NarcFreedom]

The AI narration so bad. Your voice is better.

[@lieberfreialsgleich]

Next time, use less paint! Maybe 10% of what you showed. I do it in 2 steps, first colour paint, than clear