Removing and Cleaning the VVT Solenoid - Peugeot 307

[@screwsnutsandbolts]

Thanks for watching ! Please support this channel by clicking the Like, Subscribe, and SUPER THANKS buttons. Your support will help me to continue and improve my videos 👍

[@johnsbackwithcommonsense7628]

Is this solenoid roughly in the same position for a 307 2.0L petrol engine? Thankyou

[@screwsnutsandbolts]

@@johnsbackwithcommonsense7628 Yes I thinks it's in the same place on the 2.0 petrol engine

[@johnsbackwithcommonsense7628]

@@screwsnutsandbolts Thank you for you reply.

[@pinkfloyd110]

A very good educational video and good photography (pro-quality), without any bullshit. I learned a lot from you. Thank u. Keep it up!

[@screwsnutsandbolts]

Thank you for watching :)

[@netwalk3802]

Thank you man I cleaned mine today its now better working

[@screwsnutsandbolts]

Thanks for watching !

[@fivedotsdave9723]

It would have been great to hear a before and after engine running so we could hear what difference that clean made.....

[@bendude6748]

I wish it was this easy to remove on my Peugeot 207 GTi, I've been wiggling the bloody thing around down the back of the engine for about an hour and its jammed in there tight and barely any room to get a grip on it.

[@peterrudy9207]

I suppose to prevent this , I always use an engine oil flush when changing my oil and filter . I use either AmsOil or Liqui-Moly .

[@neso476]

Thank youu sooooo much for video!!! Just tell me what are the symptoms of bad or dirty VANOS? My C4 is petrol, but sounds like deasel. Is that one of symptoms?

[@dzmicer]

it was necessary to remove the retaining ring, get the plunger, clean it, check the ease of movement and install it back

[@jamesdees8862]

Looks good that engine shame it's not the engine that's in my car though

[@Fnr5069]

Perfect sir

[@screwsnutsandbolts]

Thank you

[@adrianblok4625]

The screw was thigten with some specific momentum or just thighten to sit good?

[@CARBON10]

Nut screws washers and bolts

[@fabioeduardoromeroossa3098]

Excelente video.Gracias

[@screwsnutsandbolts]

Thank you ! :)

[@markthompson1134]

are these engines pretty realiable do they do 200000

[@mikmik4205]

Excellent video Does this Carb cleaner safe on o rings ?

[@kingfreedom1863]

Mines had a small bar with ridges and a spring at the tip

[@kaiyumkhankaiyumkhan5107]

Good video

[@screwsnutsandbolts]

Thanks

[@akmfkarim2000]

Nice video. can you make the same video for Toyota any car 1.5L

[@Esrec26]

What is the function of the oil solenoid valve, thank you. I have a citroen c4 1.4 I have the same part

[@screwsnutsandbolts]

Check this out: archautoparts.com/standard-vvt-solenoid/

[@turecekradim]

@@screwsnutsandbolts page not found.

[@saigon9143]

Love it , thanks 🍺🍺🌷🍂👍

[@screwsnutsandbolts]

Thank you! Cheers!

[@truthoutmedia]

Thanks for the video Can I ask what is the name of the part you are holding at 0:30 that you have disconnected from the VVT? When I disconnected mine the plastic casing had broken leaving just two exposed pins.

[@screwsnutsandbolts]

Were the exposed pins left on the VVT unit ?. If so, the wiring plug housing must have broken away from the VVT and came away with the plug

[@truthoutmedia]

@@screwsnutsandbolts thanks for the response.The exposed pins were actually on the wiring housing, the outer plastic along with the blue rubber has all decayed away. Would this have any ill effects on the connection I wonder? The pins seem to connect ok to the VVT but ive read elsewhere that these connectors can be problematic if slightly damaged.

[@mypeugeot307essence4]

Thank you so much for this wonderful👌 video. Good luck👏

[@screwsnutsandbolts]

Thank you ! :)

[@Fabio8Andrade]

👏🏻👏🏻👏🏻

[@screwsnutsandbolts]

Thanks !

[@nathanlee9339]

I have a Peugeot 307 with the error code p0075, I feel this might help fix this. I'm trying to find the vvt solenoid but it's not where yours is. Any idea on where mine migh be? I'm running a EW10 2.0 engine.

[@screwsnutsandbolts]

I don't know, sorry. I haven't worked on the 2.0 liter version

[@mkdalraisi307]

It's near the oil filling cap with 2 wire connector

[@easyrider020]

very helpful video thank you for posting it.i had a question did you disconnect your car battery before you start to work?

[@screwsnutsandbolts]

Yes I did

[@easyrider020]

@@screwsnutsandbolts thank you so much

[@screwsnutsandbolts]

You're welcome :)

[@roolrool3238]

That is OCV - Oil Control Valve

[@gnostman1]

Hello friend, I see that you know about mechanics. I have a Peugeot 307 with the problem of a defective gearbox ( boite de vit defaillante ) could that be the issue? I appreciate your help in advance, thank you very much.

[@screwsnutsandbolts]

I'm no expert on gearboxes, sorry. The VVT solenoid just controls valve timing.

[@miragedelta]

Same one is in 2JZ.GTE.... a bit longer

[@H3LLBOZZWildrift]

Anyone know where peugeot 307cc 1.6 16v is located? Mine wasnt at the top atleast

[@philipmaguire9209]

Would thus effect idel neutral only ? Peugeot 307hdi estate 2005

[@screwsnutsandbolts]

It's easier to detect when the car is only idling

[@benyounesmikanik4897]

Machae lahe watabarake akhi naseta3erafe bike

[@richardnewey7593]

Just unplug the dam thing and leave it unplugged. I have on my 1.8vvt vectra which has 2 of them unplugged them both months ago and my car runs so so so much better variable valve timing is only for emissions anyway. People say unplugging them causes codes and performance issues i have non of the above infact I was suffering with lag and flat spot issues when connected now im not. If you do get codes just simply buy a second hand set dont fit them just plug them in a cable tie them to the frame of the car tricking the ecu into thinking there fitted. By running without vvt is the same as having an engine without vvt unplugging only returns the cam to base setting just remember to reconnect for emissions test

[@kingfreedom1863]

Use to much oil and gas if not corrected

[@ParFektion]

Before cleaning was the idling bad?

[@screwsnutsandbolts]

It was a bit rough

[@joel.ew10a]

I suppose I'm having a vvt issue on my 307 2.0 petrol (ew10 engine). After cleaning VVT selenoid, will it be needed to "recode" the ecu? Or it is just take the selenoid out, clean it, and place it back?

[@screwsnutsandbolts]

No I don't think there's any need to recode the ECU.

[@jackkelsall2558]

I currently have engine light on my dash because of a VVT failure. I've ordered a new one. I'll be fitting it myself but just wanted to ask. Will the engine light go off once I've replaced it correctly or does it have to be run through diagnostic and have the error deleted manually ? Thanks

[@screwsnutsandbolts]

It's possible the light will go off once you drive a few miles with the new one but I'm not 100% sure to be honest.

[@jamier7073]

Does this procedure also apply to the 2012 RCZ as they are similar engines. I have a P1030 & P1062 error code?

[@screwsnutsandbolts]

I don't know, sorry

[@Esrec26]

What is the function of the oil solenoid valve?

[@abdrahmanabdullah3113]

yes wht the function of it

[@screwsnutsandbolts]

It is explained in this video: kzbin.info/www/bejne/haW1nYSodshof7s

[@screwsnutsandbolts]

It is explained in this video: kzbin.info/www/bejne/haW1nYSodshof7s

[@msanda6767]

Great video, what is the mileage on that particular car you cleaned the VVT?

[@screwsnutsandbolts]

Thanks, it had about 130,000km on the clock

[@karimgazzeh4548]

Can you please show how to remove the 2nd one (intake side). Thank you.

[@chillmaster434]

Only one at this engine

[@joebaker2175]

The prince engine has 2. It's at the back of the head, opposite the front one.

[@kingfreedom1863]

I think mines busted . When I went to pull of it Dnt look like that. I think I pulled it apart half stayed inside so I just cleaned it like so and reassembled it.🥴 tested it it works . Now for the filter . And I didn’t have to remove anything

[@СлавчоВърбанов]

Юпитер

[@raad35]

هذه القطعة غير موجودة في البيجو ٣٠٧ موديل ٢٠٠٤

[@ahmetfurkanozdener656]

Do you recommend removing filters on the side?

[@screwsnutsandbolts]

No they're there for a reason :)

[@ahmetfurkanozdener656]

@@screwsnutsandbolts OK, thanks :)

[@kalani1987]

Engine sludge seems to be the cause for vvt failure

[@viridian6903]

Hi i have a problem in the idle engine work very rought does this valve have fault

[@screwsnutsandbolts]

There are many different things that might cause a rough idle, this is just one possibility.

[@viridian6903]

@@screwsnutsandbolts i have error p0012 kfu engine

[@GlitchedMuffin]

@@viridian6903 have you fixed the issue? If you did what was the cause?

[@nourzerkaoui3844]

Marci à vous

[@lyubencholakov4201]

does the 1.6 16v 109 HP has this part installed ?

[@screwsnutsandbolts]

I'm not sure, sorry

[@dobrosavdakic1272]

Hello. Where is this on a 2.0 66kw engine?

[@screwsnutsandbolts]

I don't know, I've only worked on the 1.4 petrol engine. Sorry

[@mhamedfarci998]

Hello where to find the VVT ​​VVT Solenoid - Peugeot 307 year 2005 1.6 16v. Automatic box. THANK YOU

[@screwsnutsandbolts]

It should be in a similar position to this.

[@MertNazmiSerin]

i have also 1.6 16v petrol engine 307 2003 there is nothing about VVT

[@toxmaster1]

As far as i know 1.6 16v does not have VVT solenoid. 1.4 petrol without VVT would be quite weak for 307 heavy chassis.

[@KuldipSingh-vu8fm]

Where to find the vvt solenoid 307 my van Honda Odyssey 2002 model

[@chillmaster434]

Does it make click sounds when you shake the valve?

[@screwsnutsandbolts]

I don't know to be honest

[@mkdalraisi307]

No it doesn't

[@RBISTO541]

Can it come Antipollution Fault P0410? From thet

[@screwsnutsandbolts]

I don't think so. P0410 is usually caused by: Failing secondary air pump or relay Defective air pump check valves Clogged air injection system Blown fuse Bad EGR Valve Malfunctioning oxygen sensor Blocked catalytic converter (usually sets other trouble codes with P0410)

[@RBISTO541]

@@screwsnutsandbolts Where is the fuse and relay for EGR?

[@screwsnutsandbolts]

Check this website: fuse-box.info/peugeot/peugeot-307-2002-2008-fuses

[@scottharriswestwalesfishin639]

Is this the same on the 207??

[@screwsnutsandbolts]

I'm not sure

[@Nottsdrivers]

Yes but it,s on the front upper left of engine on 1.6 vti

[@martymartin2894]

Does anyone know where is purge valve solenoid located on 307 1.6 petrol.

[@screwsnutsandbolts]

The purge valve and charcoal canister should be located under the right hand wheel arch. You can access it by removing the wheel arch liner.

[@martymartin2894]

@@screwsnutsandbolts ok thank u

[@screwsnutsandbolts]

You're welcome

[@Sukhjinders47]

Hi can you upload aa video for this car how to fix valve lifter noise from engine.?

[@ikedichukwuchesa413]

Hello. Plesse where do I find the downshifting solenoid for my Peugeot 307 (1.6ltr). Gear is AL4 transmission. My gear seem to downshift erratically when I step on my brakes.

[@screwsnutsandbolts]

I don't know, I haven't worked on one of those transmissions. Sorry

[@DashCamSerbia]

Remove the rubber O-ring before doing this...

[@zgabeartzaiftodie8615]

What are the symptoms?...

[@screwsnutsandbolts]

Rough engine idle and poor fuel economy are two but there could be others. Here's a link: www.autoblog.com/2016/01/13/symptoms-of-a-bad-or-failing-variable-valve-timing-vvt-solenoi/

[@kaiyumkhankaiyumkhan5107]

The parce name. Plis

[@screwsnutsandbolts]

Here's a link showing the part: acornautoparts.co.uk/shop/cars/variable-valve-timing-oil-control-solenoid-valve-vanos/variable-valve-timing-oil-control-solenoid-valve-vanos-for-bmw-mini-11367604292/

[@СухайлиХалимов-ч4р]

Сеточки выброси ,лучше новый купи ,может не работает

[@husofatmic2791]

Zasto je ovo zasto se radi

[@screwsnutsandbolts]

It is one possible cause of a rough engine idle or bad fuel economy.