SDG

  Рет қаралды 7,321

SDG Electronics

SDG Electronics

Күн бұрын

Пікірлер: 18
@davadoff
@davadoff 4 ай бұрын
0:59 I’d love to learn more about the clearance/creepage rules. Especially when safety isolating from the mains. I googled the topic a few times with great difficulty finding specific answers.
@Graham1904
@Graham1904 3 жыл бұрын
Great video. Why use "L" shaped slots when the shortest distance is across the short leg?
@teikarate
@teikarate 4 жыл бұрын
brilliant video. I've got to explain creepage and clearance to my boss soon so this is great for the introduction.
@CoolNamesAllTaken
@CoolNamesAllTaken 5 жыл бұрын
Great explanation with an intuitive demonstration. Thank you!
@koolander89
@koolander89 4 жыл бұрын
what is the model of the Fluke tester?
@ristomatti
@ristomatti 5 жыл бұрын
Three videos within five days. You seem to be on fire! The moisture demonstration was excellent, the ending brilliant. Grear work! I wonder if conformal coating would have a similar effect as solder mask on the clearance distance. I assume it should help at least with the creepage distance?
@KissAnalog
@KissAnalog 5 жыл бұрын
Ristomatti Airo Yes conformal coating will help as well and will more importantly keep the surface clean (pollution down), and there is a large variety of conformal coatings with various properties. However, it is not recommended to rely on mask or coatings in place of proper spacing. Some agencies do not recognize these methods.
@MrDomyboy
@MrDomyboy 5 жыл бұрын
How is this done in EagleCAD?
@dieSpinnt
@dieSpinnt 5 жыл бұрын
Use layer 46 Milling and any polygonal shape. But at the end, this is decided what you output to gerber files and how your PCB manufacturer is treating them. Creating a PCB Outline in Autodesk EAGLE: kzbin.info/www/bejne/eXOkgoqCZZeBqbc Autodesk EAGLE - NEW CAM Processor Overview: kzbin.info/www/bejne/oKTCoaWIiaiHaK8 www.autodesk.com/products/eagle/blog/every-layer-explained-autodesk-eagle/
@cveja69
@cveja69 5 жыл бұрын
Why did you cut those traces, why didnt solder on connector holes?
@sdgelectronics
@sdgelectronics 5 жыл бұрын
There's other areas of the PCB that wouldn't withstand 1kV during the testing. These were isolated by cutting the traces
@sadasivaraov788
@sadasivaraov788 4 жыл бұрын
Thank you So much for Your Explanation.
@lmamakos
@lmamakos 5 жыл бұрын
You let the magic smoke out!
@TheEmbeddedHobbyist
@TheEmbeddedHobbyist 5 жыл бұрын
Nice demo, but I think the most important part is creapage and clearance between the mains voltage and the low voltage side the user might touch. The transformers in most Chinese psu's fall way below par on this point.
@unodos1821
@unodos1821 5 жыл бұрын
A humidity sensor would be nice.
@DustinWatts
@DustinWatts 5 жыл бұрын
Useful video!
@Mr.Leeroy
@Mr.Leeroy 5 жыл бұрын
great ending! mehdi's school))
@coldfinger459sub0
@coldfinger459sub0 5 жыл бұрын
Good demo one picture is worth 1000 words. And shut down the doubting Thomas that would otherwise open up their mouth.
SDG #115 Miniwave MDP-XP MDP-M01 MDP-P905 Mini Power Supply
18:40
SDG Electronics
Рет қаралды 15 М.
Гениальное изобретение из обычного стаканчика!
00:31
Лютая физика | Олимпиадная физика
Рет қаралды 4,8 МЛН
Cat mode and a glass of water #family #humor #fun
00:22
Kotiki_Z
Рет қаралды 42 МЛН
From Idea to Schematic to PCB - How to do it easily!
11:05
GreatScott!
Рет қаралды 1,8 МЛН
What are creepage and clearance?
11:44
Texas Instruments
Рет қаралды 10 М.
SDG #090 PCB Design Tips and Design Rules
13:49
SDG Electronics
Рет қаралды 10 М.
PCB Ground Loops and How to Prevent Them
13:01
Altium Academy
Рет қаралды 27 М.
SDG #154 How to do controlled impedance traces on your PCB
11:38
SDG Electronics
Рет қаралды 24 М.
SDG #118 Can ultrasonic cleaners damage your PCB and components?
14:20
SDG Electronics
Рет қаралды 28 М.
I2C and SPI on a PCB Explained!
15:34
Altium Academy
Рет қаралды 159 М.
SDG #138 How to Panelize your PCBs
11:26
SDG Electronics
Рет қаралды 15 М.