Seat Leon 1P 2005-2009 | Bi-Xenon HID Mini H1 Headlight projector Upgrade installation

Seat Leon, year 2005, 2006, 2007, 2008 and 2009, Bi-xenon projector retrofit Mini H1 6.0 installation video. Check out the different steps!
𝗬𝗼𝘂 𝗰𝗮𝗻 𝗯𝘂𝘆 𝘁𝗵𝗶𝘀 𝗴𝗿𝗲𝗮𝘁 𝘂𝗽𝗴𝗿𝗮𝗱𝗲 𝗸𝗶𝘁 𝗵𝗲𝗿𝗲:
retrofitlab.com/products/seat...
𝗜𝗻𝘀𝘁𝗿𝘂𝗰𝘁𝗶𝗼𝗻𝘀:
0:01 Heat the headlight to soften the sealant
0:06 Open the headlight using a flat screw driver
1:12 Remove the reflector
1:38 Disconnect the wires
1:45 Remove the low beam reflector
1:56 Remove the orginal bulb holder
2:04 Adjust the fitting of the reflector for mounting the Mini H1 projector.
2:34 Place the rubber ring on the projector
2:39 Place the adapter plate for a perfect centered projector
2:55 Screw the bulb holder
3:29 Place the new Iris shroud on the Mini H1 projector
3:37 Clean all the reflectors, shrouds and lenses
3:55 Connect the H1 splitters and replace the reflector in the housing.
4:16 Place the lens back on the housing and heat the headlight again
4:31 Press the lens back on the housing to close the headlight back up again. Clean the headlight and you're done!
𝗔𝗱𝘃𝗮𝗻𝘁𝗮𝗴𝗲𝘀 𝗼𝗳 𝗮 𝗕𝗶-𝘅𝗲𝗻𝗼𝗻 𝗽𝗿𝗼𝗷𝗲𝗰𝘁𝗼𝗿 𝗿𝗲𝘁𝗿𝗼𝗳𝗶𝘁 𝗸𝗶𝘁:
• Much better light output
• Double high beam (xenon + halogen)
• No glare
• Lower energy consumption (35 watt instead of 55 watt)
• Luxury OEM look
𝗧𝗵𝗶𝘀 𝗸𝗶𝘁 𝘄𝗶𝗹𝗹 𝗳𝗶𝘁 𝗼𝗻:
• Seat Leon (2005 - 2009)
𝗖𝗵𝗲𝗰𝗸 𝗼𝘂𝘁 𝗼𝘂𝗿 𝗻𝗲𝘄 𝗙𝗮𝗰𝗲𝗯𝗼𝗼𝗸 𝗴𝗿𝗼𝘂𝗽:
/ europeanheadlightcommu...
𝗙𝗶𝗻𝗱 𝘂𝘀 𝗼𝗻:
Facebook: / retrofitlab
Messenger: www.m.me/Retrofitlab/
Instagram: / retrofitlab.com_official
Our website: www.retrofitlab.com/
𝗢𝘂𝗿 𝗦𝘁𝗼𝗿𝘆:
Retrofitting refers to the addition of new technology or features to older systems. These days there are a lot of people who put a simple plug & play xenon kit in their halogen headlight housing in an attempt to improve night vision and looks of their vehicle. In fact they don’t realize that their headlight beams are often worse than before. Night vision achieves relatively little improvement on night vision because of a poor beam pattern, which increases the blinding of other road users. This is because their headlight housings are designed for halogen and not xenon.
A true Bi-Xenon projector update is now possible for your car. Such an upgrade will significantly improve your light output from 700-2100 lumens to 2800 and 3500 lumens, without blinding other traffic with glare from your headlight. Upgrade your headlight OEM style!
The latest high power Led bulbs will upgrade both the exterior and interior lighting system of your car. Led lighting is becoming more and more popular in the automotive market for obvious reasons. They have longer lifetime, use less energy and improve safety with their fast response time.
Do you have any questions? Do not hesitate to contact us, we are happy to help you out!
Good luck with your retrofit!
These products are not ECE-approved and must not be used on public roads in any exterior application. Use on public roads will invalidate both the operating license and insurance coverage.
#Seat #Leon1P #Aharon #Retrofit #DIY #Upgrade #Headlight #lighting #HID
#Retrofit #LED #custom #improvement

[@93JLY]

Looks so easy in this video. I did the same on my 06 Leon and takes me 4h for the first headlight.

[@KingABS]

Clean and well done ! if i was the owner i'll certainly go with the quad setup :)

[@Utubeash7]

As usual, perfect and simple from the ugly halogen to the impressive HID. Thank god for the Mini H1s :)

[@davidemainetti7496]

This process can also be used for headlights of the Seat Altea 2006? Thank you!

[@OmarAlobaid]

Look like OEM Good job 👍

[@OmarAlobaid]

***** your welcome 😊

[@danielcartel150992]

me gusto su video (Y), que tiempo se necesita para despegar la mica del faro? gracias.

[@BYKjaer]

Great job. What size is the lens? 2,5 og 3 inches?

[@mohfarouk4163]

For this leon 1p. What you recommande 2.5 projector or 3.0 inch?

[@FamilieBeer]

Perfect! Nog betere lichtopbrengst en lichtbeeld dan de OEM xenonlamp in mijn vorige Seat Leon. Ik heb nu (nieuwe Seat Leon) OEM LED verlichting; het oogt weliswaar cool, maar de lichtopbrengst is beduidend minder dan bij de OEM xenonlampen.

[@salvoritmo]

Hi, congratulation for the great job. I have a Seat Ibiza 6L 2007 restayling with original projectors. Which projectors i have to choose (h1 mini, h4, h7 and 2,5" or 3") for my car? Thank you for the answer

[@miguelalbarodriguez]

Hello, first thing, great work. Have you done any with seat ibiza 6j? Which one do I have to choose 2.5 "or 3"? And finally what PROJECTOR SHROUDS? IRIS??? Thank you in advance and congratulations on your work.

[@A51AN3RD]

Great video! But besides the fact, that you need a aut. levelling system and a washer, I'm pretty sure that such mods are ilegal in Germany. A halogen projector for H7 or H4 buls would be fine, but i haven't found something suitable untill yet. Do you guys have something in this way?

[@AntonioM91]

hola tengo el nuevo seat toledo de 2014 y me gustaria saber si se le pudiera poner a los faros los proyectores que poneis y si ustedes tambien lo poneis soy de españa un saludo.

[@juannk5112]

what is the name of the cable that you use to connect the projector to the car

[@mathewbailey1004]

Hi there have you ever done a Seat Alhambra head lights

[@Karaku5]

im thinking of getting this after christmas. will this pass an MOT?

[@Elyfik]

Круто.

[@AntonioM91]

then it is the cable carrying the projector must be plugged in the long beam , and if not being plugged ? A greeting.

[@ihoryaremenko9043]

cool...what price for this job if i wiil send my headlight to U and how many days do U need ?Thanks.

[@alvaromartin879]

hola ¿que es todo lo que necesito comprar para ponerlo y que me funcione bien? un saludo

[@gino6548]

Hola que tal !!! Tengo un seat leon ll >09 mi faro es normal , quiero dejarlo o poner como muestra el vídeo , me podéis informar y ayudar . Soy de España Madrid . Un saludo

[@Alexlue8600]

Will the original H1 be the drivelight or is it just the xenon?(:

[@turan86]

3:54, what are you doing with the blue wires?? Do they come along with the projectors? Or do I have to order them apart?

[@alancolmenarez7317]

do you find those blue wire?

[@Skayn013]

Hello Retrofitlab team Made you the assemblies for seat leon 1p1 of a kit xenon on headlight of origin? If I send you my headlight ?

[@tarikhocini724]

ou on peut se procuré des loupe pour bmw e60 svp ??

[@vanclann2640]

hi guys tell me did you reheat the existing glue to put the lense back on or did you place new glue in it

[@el_taiito5492]

sure it's new glue because this one does not soften enough with heat

[@simuk2810]

Hi I fitted xenon projectors to my original seat leon headlights I connected the shutter wire to my high beam. (Disconnected high beam connection and wired shutter wire to it) But I am getting a bulb warning error (high beam bulb). Also my shutter only works when the headlights are switched on, otherwise I have no high beam. Where have I gone wrong? Kind regards

[@grivious31]

Hello did you find a solution? I have the same problem thank you

[@kalliber]

for how long did you heat up the headlight? and how did you glue it back on?

[@Retrofitlab]

In general, 2 methods are used, with both methods, be careful and patient. Method 1 is using a regular oven. Preheat the oven at 200 degrees Celsius. When ready, switch off the oven and place the headlight inside. Make sure that the headlight is not touching any metal of the oven by placing a cloth over the grid, for example. Leave the headlight in the oven for 10-15 minutes before opening it. If the headlight kit is not yet soft enough, put the headlight in the oven for a bit more time. Method 2 is suitable for larger headlights that do not fit in a regular oven, or if your lovely wife absolutely does not allow car parts to be baked in her kitchen. A large cardboard box is used where hot air is blown through a heatgun. Make sure that the hot air of the heatgun does not blow directly to the headlight, place the headlight on small elevations so that the air can circulate properly through the box. We use a setting of 300 Degrees Celsius for 12-18 minutes / 1st lowest setting, depending on the size of the headlight. The headlight is sealed with special headlight butyl; www.retrofitlab.com/en/butyl-rubber-sealant.html This kit includes everything you need; www.retrofitlab.com/seat-leon-1p-2005-2009-bi-xenon-mh1-halogen-headlights.html

[@Addystiffler]

Doing this hopefully with a set of spare lights. Parts package link please?

[@Addystiffler]

Just found it on the info thanks

[@mertipek5158]

Mercek nerden aldın

[@devran219]

türkler bunu beğendi ama bunu yapacak usta yok benim burda

[@lawriuz69]

By the way, where tou plug these to wires from projector? Does it has a bulb inside allready?

[@lawriuz69]

+Retrofitlab yes, i mean exactly these wires. I'm actually missing complete wiring tutorial in this vid

[@lawriuz69]

+Retrofitlab thank you for your offer, but the price for the kit it is unreasonable, there are many ways to get 4 times cheaper per set. Thank you

[@reecebutcher3365]

how long do you keep the heat gun in the box for mate?

[@lawriuz69]

Retrofitlab and nothing happens to the all unit in that temperature for that long?

[@Dan91]

where can i buy the xenon things to put them on my lights?

[@Retrofitlab]

www.retrofitlab.com / www.retrofitlab.com/en/seat-leon-1p-2005-2009-bi-xenon-mh1-halogen-headlights.html

[@AntonioM91]

El proyector que instalas lleva un cable que es para el obturador, que funcion tiene eso y donde se tiene que enchufar? un saludo.

[@alancolmenarez7317]

supiste para que era ese cable?? compre el kit y me estoy dando cuenta que me hace falta ese cable !! no lo encuentro en internet

[@juanantonio8561]

@@alancolmenarez7317 que solución le diste?

[@andrewstirton8636]

dos this need any coding to work with car once done? Cheers

[@lawriuz69]

+Retrofitlab he means that needs coding to make bixenon work, because i know there is an option in vcds coding when you have bixenons installed

[@kuken166]

Great video! What is the purpose of the cardboard box and hair dryer?

[@Retrofitlab]

Thanks! It's to heat up the headlight so it's easier to open :-) retrofitlab.com/apps/help-center#hc-at-what-temperature-do-i-heat-my-heatlight-to-open-it

[@Jenda1M1]

hello, how big are the lenses? 2.5 or 3 inches? Thank you

[@Retrofitlab]

2,5 inch ;-)

[@el_taiito5492]

Have you ever done retrofit on seat ibiza (2002-2008) ? apparently the glue does not soften with heat, is that true? have you some informations on this ? sorry for my bad english, good work ! :)

[@el_taiito5492]

***** Yes I think it's permaseal, do you know how much time in oven ? Or how much time and which temperature in the box with heat gun ? (I think it depends of the size of the box ? =))

[@el_taiito5492]

***** And in oven ? thank you very much

[@el_taiito5492]

***** ok, and how long I let it in ? thanks :)

[@taiite1279]

***** Ok thanks :) and which one fits better 2.5" or 3" projector in my Seat Ibiza 6L ? Thanks very much for your help

[@el_taiito5492]

***** Ok, last question I think :p, which shroud will fit the best ?

[@radu_mol2935]

how much time do you heat the headlamp

[@Retrofitlab]

Leave the headlight in the oven for 10-15 minutes before opening it. If the headlight kit is not yet soft enough, put the headlight in the oven for a bit more time.

[@radu_mol2935]

@@Retrofitlab i had one opened and what can i say its just...i respect you man,it took me one day to finish one headlamp a lot of work to do,mine are oem bixenon but i just wanted to clean the lenses

[@Retrofitlab]

Thanks, yes quite hard work with permaseal, but practice and some good tools help :-)

[@camryle5590]

Very very nice. but, please show us the results

[@camryle5590]

Retrofitlab why? I think you should capture all your works because the light result is the most important thing among all process

[@tommasodidomenico6021]

Salve io ho montato questi fari con la stessa lente e cover,ma ho problemi con la regolazione dell'altezza del faro

[@Retrofitlab]

Potresti dare un'occhiata a quanto segue; si tocca / è bloccato davanti o dietro? È su entrambi i lati? O forse un connettore per le viti di regolazione dell'altezza non è collegato? Contattaci se hai bisogno di ulteriore aiuto. www.retrofitlab.com/en/faq-1.html

[@tommasodidomenico6021]

@@Retrofitlab ci ho messo dei spessori per far si che il l'altezza del fascio si alzi un po,ma avverto molte vibrazioni della luce,

[@Retrofitlab]

@@tommasodidomenico6021 Could you please send us an email ? ([e-mail])

[@tommasodidomenico6021]

Salve quanto costa fare lo stesso lavoro su questi stessi fari?

[@Retrofitlab]

Si prega di contattare l'assistenza clienti di Retrofitlab, [e-mail]

[@Edwin.graz0]

Que medidas tiene la parábola

[@Edwin.graz0]

no lo vendes en mexico y cuanto cuesta con envio al 55120

[@mordehaimmateo1110]

Do you also order another seat ??

[@Retrofitlab]

Not sure what mean. Could you please rephrase that for me?

[@chicharolucas5040]

Alguien lo a hecho Aki en Mexico me interesa mucho Uno's para mi Leon cupra 2008

[@Retrofitlab]

Hope somebody in Mexico can help you, there should be some retrofitters there!

[@tommasodidomenico6021]

Salve li potete fare per me?

[@Retrofitlab]

Sorry, we do not offer the retrofitservice anymore. Please take a look at our website for our dealers: retrofitlab.com/pages/our-dealers

[@marksn4020]

If i had a garage maybe

[@Retrofitlab]

You can also do it at home without a garage, we also started that way :-D

[@kingspeedy4026]

please, this light have ventilation? not to get wet

[@Retrofitlab]

No, they are sealed properly and to prevent moisture we also have special breathing vents

[@7470038]

Seriously? maybe just buy from valeo..

[@Retrofitlab]

Yes, very serious. Cheaper and better performance than the Valeo xenon headlights....

[@OmarAlobaid]

Look like OEM Good job 👍