D.i.Y. the Stubborn Crank Bolt, showing how to remove this bolt using a good old Serpentine belt #BeltTrick #repair #automotive jfGarage4k
Пікірлер: 33
@mastermech-021311 ай бұрын
Should have started with the impact tool bruh😂
@jfGarage4k8 ай бұрын
At this time my Impack Not strong enough to do this Job. Lol
@jfGarage4k8 ай бұрын
Im Breaking this Bolt loose first and finish it off with a Tiny Impact 😅
@nevinkuser98928 ай бұрын
Need a 1 inch impact and 50 hp compressor. It'll set you back 10,000 bucks.
@Red_Cp3Ай бұрын
@@nevinkuser9892you really don’t, we did a timing belt and water pump on a j30 like 2 days ago and the crank pulley bolt came off with the Hercules 1/2 inch impact form harbor freight. And if that doesn’t work you can always pull fuel pump fuse and attach a breaker bar to the crank bolt wedged between the control arm with the crank pulley holder tool from auto zone that’s 20$ and crank the engine. The starter turns the motor and the breaker bar holds in place that’s normally enough force to break it free
@djmystery72358 ай бұрын
That’s like picking a lock and then using the key after you get it turned 😂
@مأذونشرعي-و7ج7 ай бұрын
اتبعت الطريقة هذه نجحت معي و واستطعت فك صامولة بكرة الكرنك
@gogo.yubarii7 ай бұрын
dude. thank you.
@jfGarage4k7 ай бұрын
Happy to help
@marekoros92029 ай бұрын
Super pomôcka Ďakujem.
@stevencaballero70727 ай бұрын
Let that socket wrench brace itself on the ground and turn it over. The starter will break it free has worked 5/5 times for me personally.
@jfGarage4k7 ай бұрын
True but this engine on the floor dosent start lol.. But becarefull some engine spin counterclockwise
@gabrielark6353 Жыл бұрын
Thank you, how do you get the pin out of it's stuck and can't grab it?
@jfGarage4k Жыл бұрын
Try to chisel it out with a hummer, good luck hope you get it out
@gabrielark6353 Жыл бұрын
I will try that next time I'm doing something with it again
@01abihsot Жыл бұрын
Why not skip the ratchet and just use the impact
@GusMortis Жыл бұрын
@@01abihsotuse a breaker bar to get it started to save your impact.
@jfGarage4k9 ай бұрын
One reason to make the video a little longer..lol
@garyparrish49072 ай бұрын
My impact is all you need.
@addisoncoughran73266 ай бұрын
Your a goat bruh! 😊
@NeutronX1017 ай бұрын
Why not keep the belt on?
@gavin-sg6yq3 ай бұрын
man mine has 4 10mm bolts then one big 30mm bolt and i cant get the 10mm bolts off
@Mdsojonuddin628 ай бұрын
😮😮😮
@clemenstee953210 ай бұрын
Der Rostlöser 😂😅😂
@donaldkinzel830710 ай бұрын
Put a impact on it!
@accountemail97126 ай бұрын
If there's no compressor available and no other impact guns work, I'd try this.
@romanborovsky986210 ай бұрын
Там жидкий ключ не поможет, только ударный инструмент
@DannyDisharoon10 ай бұрын
Won’t work. Sometimes even 😮heat is needed on these 😅😮😮
@Morakovskiy9 ай бұрын
Да а потом резьба на натяжителе разбивается
@mateidaniel17829 ай бұрын
Un profesional
@jfGarage4k9 ай бұрын
Was only done in the garage shop with lowbudget 😢😟
@inquisitormasterfan440510 ай бұрын
Old school trick too bad
@michaelmccoy46559 ай бұрын
1/2 inch impact take it right off bro wasting time