Donations www.paypal.me/SiRobb/ www.amazon.co.uk/shop/sirobb As an Amazon Associate I earn from qualifying purchases. Using my Amazon links does not cost you any extra.
Пікірлер: 164
@Tomoose19857 жыл бұрын
I have to say Simon your videos are simply excellent. The calm and methodical approach you take to your work is to be admired. Thank you for taking the time! Tom.
@sirobb7 жыл бұрын
+Thomas Emmett ..... and thank you for taking the time to comment Tom. It's appreciated.
@mattlawton47152 жыл бұрын
@@sirobb was there no sealing washer or is it stuck in the chamber. Great video also.👍
@amojak6 жыл бұрын
another method i have seen done is people slightly loosen the bolts , squirt in cleaner and then run the engine. Then they stop it and check to see if the bolts are now tight again, i.e. the injector has moved up a little and freed off. the pressure of the combustion chamber is your friend when it comes to removing a sticky injector it seems.
@rickchapman37072 жыл бұрын
I have been a mechanic 34 years and this is a superb video Simon. Calm collective manner taking your time to plan your attack without damage. I have a mercedes sprinter with the same problem this video gives me hope for removal. 5 STARS
@sirobb2 жыл бұрын
Thank you. I've had a couple of Sprinters which have luckily not needed any injector work which was a relief given the access. Good luck and I hope the fix goes well for you.
@davidelliott5843 Жыл бұрын
@@sirobb I think all of these engines need more attention than we realise. Popping out the injectors at 50K miles would be easy and a good coating of high temperature anti-seize would keep them removable for when that EGR soot needs cleaning up. PS I have a Fiat 1.3 JTD sooted up and a jammed injector. This video has inspired me to soak it.
@garyprocter18935 жыл бұрын
Thanks for the help SiRobb got me out of trouble with going garage top man!!!
@5e34nut4 жыл бұрын
You sir are a saviour in disguise I can't thank u enough for this video
@trophy19995 жыл бұрын
Removed my injectors yesterday using this calm and methodical approach. Only one injector was seized, but eventually came out with plenty of wd40, time left to soak and plenty of tea. Cheers for the video. I was given an estimate for £1,000 to have the job done! Saved me a fortune.
@arnoldaszukas71599 ай бұрын
I've been told £1600 to fix mine. And I got 3 injectors leaking. Trying to do this myself
@johnswimcat7 жыл бұрын
Brilliant, thank you. You must have saved a fair few people from having to buy a replacement engine
@sreviz7 жыл бұрын
Thanks again for sharing the valuable information Siroob!!!!!!!
@ikome200220004 жыл бұрын
Hi Dear, thank you very much from South Africa. You video is the best that I have ever watched in my entire life on You-tube. I use your solution and it took me less than 15 minutes to take out an injector that I have been struggling with for over 2 days to take out. Thanks once more you are a star
@jonathancolling22846 жыл бұрын
Cracking Video!! A very very methodical and intelligent method. Thanks for posting this up
@AmbroseAgde2 ай бұрын
Excellent video. Thanks a lot for sharing the knowledge. I love your careful, patient approach to the job. Proof that car mechanics is not at all about brute force but intelligence and precision instead. 😊
@marcelhorstmann64358 ай бұрын
Thanks this was very helpful. I had a seized injector on a BMW N57. After a few hours of soaking it in WD-40 / carb cleaner, trying to rotate it back and forth, starting the engine to heat it up - it eventually broke free! Save me time waiting for a special removal tool.
@mreuclid2232 жыл бұрын
Thank you SiRobb. Used lots of brake cleaner, time and a little wiggle to get an injector out of our Ford Kuga. Would have given in if it hadn't been for this video
@jcagam38113 жыл бұрын
Nobody explained it any clearer than this. Thanks sir for sharing your skill.
@coolvideos8864 Жыл бұрын
Use carb cleaner! I just said it simpler
@vintagesteelgarage10 ай бұрын
Excellent guidance. I'll be trying this tommorrow.
@effimia37 жыл бұрын
much thanks, I'd more or less given up trying to remove 3 stuck injectors in my 2007 Vito, even after 3 days of soaking in various liquids, the lasts one was acetone, which probably helped. took to the erg valve /throttle cleaner and using the clamp eventually got them move side to side, then started lifting them, again using the clamp upside down. All done now, no leaks.
@meadroad6 жыл бұрын
I’ve gave up on my 2006 Vito, 2 days of trying to move no 1 injector & 2x cans of oven cleaner later....... The strange thing is, since it started ‘chuffing’ it pulls better than it ever has !!!
@Surferant6665 жыл бұрын
Im stuck on my vito 638... Stuck solid
@stephenbowker9364 Жыл бұрын
What a brilliant video. Helped me completely sort my seals. Well done mate 👍👍
@daveys7 жыл бұрын
Great video! Just shows that knowledge of the fault and patience is invaluable in this type of work.
@Egon19824 жыл бұрын
@emigrate you can always emigrate by plane ;) he showed the version of how to remove it without damaging something that is in good working order. So you need to replace seal for about £13 a bag of 50 washers. That can last you to sort out 10 x d5 engines. Without spending £180 for a cheapest aftermarket injector replacement.
@colauty25985 жыл бұрын
Whoever said " Patience is a virtue " must have been in your company lol.... Excellent vid' cheers mate : )
@01walef2 жыл бұрын
Another helpful video for me to hopefully overcome sticky injector valves. My take out is, let the solvent and time do the job hir you and stay patient. Regards from Germany, Waldemar
@rbondy0084 жыл бұрын
Helpful for my job tomorrow. Thank you
@jackhardwick97502 жыл бұрын
Brilliant stuff, it worked for me - thanks for sharing this saved a lot of headache
@scotty63464 жыл бұрын
I am about to buy a V70 D5 163bhp, Your video's are a godsend mate! Subscribed.
@Egon19824 жыл бұрын
Hi. Thank you very much for those very informativs videos. Just looking after some s60 d5 so thats pushed me towards looking for common faults and solutions :)
@danielkemmett75616 жыл бұрын
this video helped me from start to finish so easy to do if your a patient person i think patients is key to doing this job garages make it sound like removing an injector is impossible to do yourself but if you follow this video and be patient you'll get it out if anything i found that the annoying part was actually cleaning the injector port and the injector itself
@malcolmyoung78666 жыл бұрын
Nice video...My TD4 wasn't as bad as this car but my main form of attacking the removal was to run the engine until very hot. I think I did remove as much dirt etc from around the injector seat before removal to prevent it dropping into the injector port/cylinder. Once hot and everything was disconnected I used a small pry bar under neath the the main injector HP connector an levering gently on the inlet manifold...it took very little effort and no damage was done. I had bought a removal kit just in case but still haven't needed it, as of yet.
@trophy19995 жыл бұрын
Hi Malcolm. I am about to remove my injectors on my TD4, so its recurring to know this method works.
@gromett6 жыл бұрын
You have just saved me a lot of time. Never changed an injector before but needed to do one on my Fiat Ducato. WD40 and lots of wiggling and it came out in a few minutes. Thank you :D
@garyfinnigan38587 жыл бұрын
Excellent video, cheers
@davidelliott5843 Жыл бұрын
I am stripping down a Fiat 1.3 JTD with broken cam chain. It’s badly coked with carbon so I want the head off to clean it safely and confirm there’s no further damage. One injector is stuck solid. Thanks for reminding me to try carb cleaner (or in my case cellulose thinners). It’s now soaking so we will see how it goes.
@pashsamra98822 жыл бұрын
Mate thank u very much live saver I was stuck on it for 12.half hours
@StBlazeyModelWorld3 жыл бұрын
Brilliant Thank you so so much Si
@gavinjones70063 жыл бұрын
Thank you Simon, I will have fun trying to get two leaking injectors out. I think they have been leaking for a long time after towing a trailer ute smells of diesel extra load of trailer must have pushed out some carbon.
@jamesk79843 жыл бұрын
Great video thanks, feel I'll soon be taking the injectors out of my 2.0 cdti vivaro
@sirobb3 жыл бұрын
Ooh good luck with that. That particular engine can be a horrible injector to remove due to galvanic corrosion so make up a 50/50 mix of ATF and acetone and put it around each injector port repeatedly for a few days before even attempting anything.
@stevesvids6 жыл бұрын
Great video. Thanks. Very useful demonstration. A nice calm methodical process with ideal results. I'm going through the process of trying to get my Renault Trafic injectors sorted and everyone seems to make such a drama out of the situation in getting them out. I'm gonna do it myself I think as everyone is quoting stupid money. Wish you lived near Reading buddy cos I'd drop it at yours for the fix for sure. 😁 All the best. Thanks again . Steve.
@nicolafaulkner94996 жыл бұрын
Steve D hello I have monervo van the injector bracket broke so now need new bolts to put back in as the old ones be stretched mechanic says please where did u get yours ?
@vpm2342 жыл бұрын
Thanks I learnt something from you.
@marcomeurs4624 жыл бұрын
Thanks!
@SupremeUnicorn4 жыл бұрын
Thank you for your videos that have helped me plenty of times. How can I clean all the mess that's left inside the injector housing? can I use carb cleaner? is there any risk if bits go inside the injector hole?
@gasgiant71224 жыл бұрын
Ooooh 13.00 just like a dentist pulling a tooth, 💉 great job Si, patience of a saint.
@jurajura1117 жыл бұрын
You Have the best videos.
@sirobb7 жыл бұрын
Maksims Korkins Thank you very much!
@hereandthere47636 жыл бұрын
Thanks for this Simon. All I can say is it works well! BTW trying to place your accent - East Midlands area is my guess...
@BensWorkshop Жыл бұрын
Many thanks for that. I have a similar problem with a tarred in injector but in an X Type (like a Mk 3 Mondeo). I have a tool for pulling a non compliant injector but suspect I can't move the collar for tar. Will try a warm engine and carb cleaner. (Followed by a hammer on my puller)
@iainbanachowicz83187 жыл бұрын
I thought it was just me who had a broken engine cover mounting. By the way. Great video and handy tip :)
@sirobb7 жыл бұрын
Iain Banachowicz Thanks. Yes, nearly all our engine covers succumb to heavy handed mechanics unfortunately.
@iainbanachowicz83187 жыл бұрын
Mine is normally the dipstick. The amount of times I've broken that while working on my D5.
@jsurridge50015 жыл бұрын
Great video
@davidroper69092 жыл бұрын
You sir are a star!
@TheHamouda2 жыл бұрын
thank you for help
@tonyroche88412 жыл бұрын
This is the job I'm attempting this week Simon! Out of interest could you soak the injector in carb cleaner to clean it once it's out?
@davidmorgan37893 жыл бұрын
Hi SiRobb, great video indeed. One thing, I have the connections to the injectors currently all removed on Citröen 1.6HDi engine and so, in the absence of being able to run it for a while would initially heating around the base of the injector with a hot air gun help much or should I just stick with the carby cleaner?
@sirobb3 жыл бұрын
I wouldn't use heat at all.
@fanatamon5 жыл бұрын
Sick vid thanks man
@gstree5 жыл бұрын
Been using the same method for years on hundreds of them and never broke anything at all, The only thing that I do different is I use cellulose thinner as it's cheaper and there is always a 5 litre can laying about in the workshop !!!! This is the first thing I look at when customers complain of an exhaust smell inside of the car when standing still in traffic but will disappear when on the move. and have normally been proved right. Sometimes some injectors rust in, especially if engines have been power washed frequently and can be a pain to get out but warming the engine and using something like plus gas for a few hours sometimes works.. It just depends who is going to do the work and how long a vehicle can be off the road, if it is needed quickly (like a delivery van) then a puller will do it but can easily ruin the injector so that has to be priced in as well; As most of us in the trade know some of them are a lot of money and also most now have to be coded in. However the video is informative and can save people a lot of money (if they have the time and patience) to do a DIY job.
@Golommod4 жыл бұрын
Nice one mate
@JamesMcl5 жыл бұрын
Will there being any play with the clamp still on or do you need to remove the clamp first? Also was size torx bit do you need to take the bolts off the clamp? Thanks
@sirobb5 жыл бұрын
You have to remove the clamp. The torx is either T20, 25 or 30. I can't remember.
@JamesMcl5 жыл бұрын
Ok, thanks for the swift reply. By the way, great vids. Youve saved me a small fortune in the past. Keep them coming.
@steveprentice45134 жыл бұрын
Patience will get you far in life.
@spoonforthought35344 жыл бұрын
Old vid, still useful! Thanks for the carb cleaner trick! Is it’s a denso c.rail? Looks the same as ranger/bt50 06-11. What’s your view on cleaning injectors diy?
@sirobb4 жыл бұрын
It's a Bosch fuel system in this video. I would only clean injectors using Liqui Moly Diesel Purge never by disassembling. There's a video in my Playlist called Cars.
@spoonforthought35344 жыл бұрын
SiRobb thanks very much! On ranger/bt50 wlc (06-11) it’s Bosch pump to denso c.rail. Mine has been sweet for 160,000mi without any injector servicing 🥺. To my knowledge it’s never had any additives so I don’t know why I put “a quantity” of reddex in a full tank and ran it through, briskly. 550 snake oil miles later am blowing blue smoke like crazy, breather pipe is to atmosphere so knew straight away 🌫. Can it really be “dislodged carbon has to go somewhere” and naff an injector into leaking through the seal? The DOHC has a bolt on carrier with 4 retrospective seals that seem to be a weak spot. Also many of our Australian cousins like running 3ml of 2stroke per L on this particular system due to these injectors gunking up and sticking. It’s cheaper to put purpose made additives through....oh that’s why I did it! Am to purchase some moly with haste and checking your playlist out now cheers for the help!👍 Your vids are so concise and methodical there therapeutic 😁 much love
@necrofobic64458 ай бұрын
Top video this mate ❤
@ashleycarter7653 жыл бұрын
Brilliant, this video has given me the confidence to have a go at my one's. Just one question you say that you only need the tool on euro 3 models. Mine is a 1.6 and the injector looks pretty much like yours. How do you do the circlip on stuff other than the euro 3 model.
@sirobb3 жыл бұрын
The circlip isn't on all injectors so yours may just be held in with the clamp only.
@ashleycarter7653 жыл бұрын
@@sirobb many thanks for the reply. I done exactly as you said to do on the video tonight. With a bit of work with that carb cleaner for 3 nights 3 of the injectors popped out. Just on the last one that's a bit stuck tomorrow. I do have circlips but there intact so will be leaving them. Once again thanks for the video it worked a treat.
@izyfication Жыл бұрын
Thank you for your vidéo 👍🏻
@TheHamouda2 жыл бұрын
top video. in 11.28 minute did you put back holding nut or only screw back with out nut?
@sirobb2 жыл бұрын
The nuts are in but slightly loose. The injector does not screw in.
@letmefixstuff7 жыл бұрын
Great work. I've done a lot of repairs on my V70 '04 following your video instructions! I really would like to now if you had any V70 or S60 with a simmilar issue: My V70 has a very ugly feeling in the steering wheel when i'm going long curves. It's a feeling in the steering wheel like you where driving on ice, the steering wheel is pumping some degrees back and forth, back and forth... I've deactivated the steering angle sensor by unplugging the cables so the sensor can't send any data to the CEM. And it helped a little bit. It's smoother in curves but now without DSTC and that's not a final solution for it. Do you maybe know what part of the DSTC System can produce such issue? I will replace the SAS with a brand new one in the next time, but i think it will not solve the problem at all. By the way: I know a dozend of V70 drivers with the same problem, maybe you can figure out what's about it? Many thanks.
@sirobb7 жыл бұрын
Briix Hi, thanks for your comment. With your steering issue, my first question is what is the colour, smell and level of your power steering fluid?
@letmefixstuff7 жыл бұрын
SiRobb I've flushed the system and replaced the old one with Volvo original, green coloured. My Dealer even replaced the steering box with a refurbished one, but nothing changed. There is also no broken pipe in the servo-oil reservoir, like it often happen. Only without permanent DSTC the steering feels fine.
@sirobb7 жыл бұрын
Briix OK well in your position, before shelling out for an expensive new SAS, I would invest in Vida if you haven't already. You can bring up all the data for the various DSTC inputs and compare with what it should be. Vida and Dice is invaluable and is actually very cheap because when you're done with it, you sell it. There's a healthy demand for a working setup so you lose very little money.
@letmefixstuff7 жыл бұрын
I already have a DICE from China and the Vida Software. The errorcodes are typical for the issue: SAS internal fault, no communication, etc. Most people with that issue replaced the sensor without any effect. Thats why i think the main problem is way deeper in the system. But it's a glance in the crystal ball for you if you never heard about this problem. Nevertheless i thought it would be good to ask. :)
@kayb25585 жыл бұрын
Perseverance Baby!!!
@blake9358 Жыл бұрын
They smoke like crazy when injector siezed
@Genuineallmetalbutcher Жыл бұрын
Exactly what’s happened to mine. One stuck open and flooding white smoke. Ye gods the stench.
@mickramo4985 жыл бұрын
is the problem made worse by us ignoring the chuff chuff when it first starts ?
@Genuineallmetalbutcher Жыл бұрын
What’s the process if you have zero treacle, zero carbon in the wells. Beautiful clean wells and still have injectors that feel like they are held in with Araldite?
@sirobb Жыл бұрын
You might have galvanic corrosion where the different metals of the injector body and engine block start to become one and feel like they'll never part. My suggestion there is a 50/50 mix of automatic transmission fluid and acetone which makes a very effective penetrating oil to get into the tiniest of places and break down the corrosion. Off the shelf *penetrating fluids* in a can will work in time too.
@toxic8344 жыл бұрын
what make of carb cleaner did you use?
@sirobb4 жыл бұрын
I can't remember but probably Wynn's or Holt's
@jawaczman7 жыл бұрын
any idea on smoke and fuel smell on start up once warm clear
@sirobb7 жыл бұрын
jawaczman Test your glow plugs. See my video here kzbin.info/www/bejne/aoHSkGSmg614Z7s
@gheorghinacov60084 жыл бұрын
Is it possible to have different classes on the injectors and program them so the engine could work optimally? Thank you!
@sirobb4 жыл бұрын
The Euro 3 D5 has injector classes and the ECM is programmed accordingly at the factory. If you fit 3 or more of a new class of injectors, you need to program the ECM for the new class.
@gheorghinacov60084 жыл бұрын
So the ECM can be programmed to give to different classes injectors at the same time the right amount of fuel? And if it's possible, could it be done using VIDA 2014D?
@sirobb4 жыл бұрын
On a Euro 3 D5, the engine is fitted with injectors which are all the same class and the ECM is programmed to match the class. The ECM can only be programmed to one class at a time so for optimal performance all injectors must match the ECM. You can change the ECM class with Vida but for optimal performance all 5 injectors must match the class programmed into the ECM. If you fit mixed classes of injectors, you cannot program the ECM for each different class of injectors so performance will not be optimal.
@gheorghinacov60084 жыл бұрын
@@sirobb Thank you for helping! I hope you will upload further more videos with diesel Volvos. All the best!
@runningman44593 жыл бұрын
If squirting a little carb cleaner at it is all it takes then it certainly isn’t stuck!
@sirobb3 жыл бұрын
A little carb cleaner? It took 2 days.....
@alastairmackay97993 жыл бұрын
great vid but once the injector is out how would you effectively clean out the carbon from the injector itself and the surrounding area
@sirobb3 жыл бұрын
Carb cleaner for the injector and carb cleaner soaked into a rag wrapped around a screwdriver to clean the port. This video only covers injector removal. I have others covering replacement and prep.
@alastairmackay97993 жыл бұрын
@@sirobb thank you
@shimonbain8 ай бұрын
I have a tucson d4ea engine. The injector spins left to right. But i cant get it to pop up
@antonzoko71956 жыл бұрын
Hello, please tell me in what order it is necessary to insert injectors
@sirobb6 жыл бұрын
Anton Zoko I'm not aware of any order.
@stephencrabb51232 жыл бұрын
Mine is truly seized Merc ml 270 it will not turn or move in any direction even with a slide hammer won't move any help?
@johnkerr80195 жыл бұрын
This is a great video, like so many things in life, being patient and focusing on thne job at hand, usually gets you there. Does anyone out there in youtube land know where to buy the carburettor cleaner individually , as most places appear to be selling the cans by the dozen. Hello from Glasgow
@sirobb5 жыл бұрын
Thank you for the comment. Single can carb cleaner seller in the video description.
@nicam492 жыл бұрын
I know your query is 3 years old... but Toolstation sell Holts carb/brake cleaner.
@johnkerr80192 жыл бұрын
@@nicam49 Hello, thanks for taking the time to reply, but I've now sold the vehicle I was having a problem with. I now know where to go should a problem like that surface in the future. Thanks John Kerr
@fierakuitali93133 жыл бұрын
Was the injector very stuck ? I have one very stuck and don't know if it work
@deizle615hitz3 жыл бұрын
How did u get that stuck injector out
@michaelsedgley4949Ай бұрын
What is the best lubricant - does it need to be special fuel injecter lubricant.
@sirobbАй бұрын
Any regular *penetrating* fluid. Brands like Plus Gas and WD40 but check it's the penetrating version not just lubricant.
@patgaffney96374 жыл бұрын
Awesome
@danstones633 жыл бұрын
Have you ever had one injector sit lower than the other? Recently removed the injector which is misfiring and it has 3 copper washers on it! Removed them and replaced with 1 genuine Volvo one, and it doesn’t seal and just chuffs! The injector also sits lower in the head 🤔 confusing!
@sirobb3 жыл бұрын
No, never heard of that.
@pop54735 жыл бұрын
just leave the engine running is exactly what you wanna do,,,drive it and leave it running minimum 1 hour in idle after ...Carbcleaner wont pas the top seal on many injectors..When up insert a rag ,,clean around the whole and then vacuum ,,remove seals and washers after vacuuming,,bobs your uncle
@chlyon2 жыл бұрын
Secound best video on you tube only behind Grinding the crack
@TheHamouda2 жыл бұрын
ok.mine 1.6 hdi .nut and screw.i have the same problem. and I want to try your method.im not sure if I have to take out screw .as many people says .they will be disturbed. already I took out nut.i put some carb cleaner .still no movement
@sirobb2 жыл бұрын
If the engine runs, you loosen bolt holding down the injector slightly to allow the pressure underneath the injector to slowly push it up. As I say in the video, I *can't recommend* you do this so it is entirely your decision.
@RussianSpaceman4 жыл бұрын
i've removed a few of these, but yesterday fixing my own one i got stuck on cyl1 sattle bolt, it broke 3 torx 30 on me, cleaning, and even a bit of heat and it still wont move, what is best course of action in your opinion? thanks
@rogerramsay8417 Жыл бұрын
Recommended
@drewtaylor69822 жыл бұрын
I use liquid oven cleaner not spray leave it for 2 days then wash t he carbon away it was amazing
@krysieks7 жыл бұрын
Is that injector replaced in another video? If yes why all this happened?
@sirobb7 жыл бұрын
krysieks No, this is on a V70 I'm working on. This isn't my S60.
@krysieks7 жыл бұрын
I see. I'm preparing to remove, check and clean injectors on my s60 2002 (hard to start on cold days), so i rather want learn on someones mistakes that on mine :)
@tommyulgenes69726 жыл бұрын
How can i get the copper seling out after removing the injector?
@sirobb6 жыл бұрын
Tommy Ulgenes kzbin.info/www/bejne/Y5SZZYF6eaeCm9E
@tommyulgenes69726 жыл бұрын
SiRobb thank you for your answer, great help
@sailorbob741335 жыл бұрын
In my case the the bottom half of the injector stayed stuck and I just managed to unscrew the top half. Screwed it back in after removing the injector internals with a magnet and got it moving clockwise, but I'm afraid I might just be stripping the threads in the injector itself...
@sirobb5 жыл бұрын
I'm sorry to hear that but as you can see in the video, I don't unscrew anything.
@sailorbob741335 жыл бұрын
@@sirobb I wasn't blaming you just was warning people that the top half can come undone and then this won't be effective in that case.
@191246mann15 жыл бұрын
don't expect this to work on every car I've had some I have ruined trying to get out ,and when you do this turning bit if it is really tight you will just be unscrewing and screwing up the injector at the middle ..like when you take them apart so don't fall for that one check carefully that when it turns all of it turns .not just the top part.
@sirobb5 жыл бұрын
You can't check that all of it is turning as the seam is out of sight in the injector port. You just take your time, allow the carb cleaner to soak and hope for the best. There are no cheap, foolproof and guaranteed ways to solve this problem but this method has worked many times for me.
@ThePCFerguson5 жыл бұрын
Rob do a video on the dreaded on volvo s60 d5 2008 185 bhp feckin dpf issues. doing my head in volvo tech just want you to buy parts and charge for vida. finally found a fault they cant fix.... its killing my pocket money
@MrStubat5 жыл бұрын
Tried it but the bottom of the injector stayed stuck and screwed off. Injector stuffed and half still in there. Only screw clockwise is my idea.
@sirobb5 жыл бұрын
You haven't followed the video because I don't screw either way in it. It's a gradual twist left then right but never so much that you separate the injector.
@MrStubat5 жыл бұрын
SiRobb ...fair enough. But first twist should maybe be clockwise first. It’s obviously an extreme case but it did happen. Luckily I ended up getting it out and have a spare.
@TheRepairer4 жыл бұрын
I’ve been trying to remove a a Volvo D5 injector now for three days, its been soaking in penetrating fluid the clamp is free and I’ve cleaned out the engine cover of black gunk, I’ve made a bath for the penetrating fluid (plus gas )in the engine cover using some blue tac stuff . It’s Still stuck solid despite my best efforts. I can also drive the car with both clamp retaining bolts loosened and it’s still seized. Any ideas anyone?
@sirobb4 жыл бұрын
Use carb cleaner as per the video. Penetrating fluid isn't going to break down carbon.
@TheRepairer4 жыл бұрын
SiRobb I’ve already soaked it in carb cleaner for two days but ran out I’ll try some more
@sirobb4 жыл бұрын
Soak up all of the penetrating fluid with kitchen towel first before refilling the injector recess so the carb cleaner isn't diluted and don't waste your time attempting to pull the injector until you have good rotational movement through about 45° clockwise and anticlockwise.
@TheRepairer4 жыл бұрын
Update:- the injector has now been removed after 4 days of carb cleaner applied after every journey (twice daily) I did a 60 mile motorway drive at the weekend with the injector bolts loosened 1 turn. Towards the end of the journey I felt the car hesitating a little then at a set of traffic lights and heard the clanking noise as the injector took up the slack in the clamp , I attempted to remove it back home in the dark of night. but it wouldn’t twist or hammer up or down. One good overnight soaking later and a with a hot running engine on the driveway I again hooked a bodywork slide hammer under the injector nut and pulled the injector up a couple of mm further. It was still stuck but quite raised, I got the injector twisting with mole grips and hammer taps at first then I could twist it by hand. I successfully removed the very stuck injector yesterday! Patience and perseverance is key I came very close to loosing faith!
@sirobb4 жыл бұрын
Your final couple of sentences sum up the job perfectly so well done. You've saved yourself literally hundreds of pounds.
@Skambutisz6 жыл бұрын
It wasn't seized mate.
@Sea2Skyward5 жыл бұрын
How do you go about cleaning the hole and on top without getting all that crud in the engine? Or does it matter if it gets in the engine?
@Fosgen5 жыл бұрын
Use vacuum cleaner.
@TheGuy0307705 жыл бұрын
You ever tried gasoline to try and break up that gunk? I think gasoline would refine that diesel residue much easier.
@sirobb5 жыл бұрын
I have no need for petrol so it would be more expensive for me to buy some just for jobs like this. Carburettor cleaner in a can is much more versatile and safer.
@johnnybravo47235 жыл бұрын
actualy this is mistake.. engine must be hot when removing injectors as aluminium streches 3 times metal does so when engine is hot gives clearance so you can remove injectors...
@sirobb5 жыл бұрын
The injector came out so how is it a mistake?
@krtolebiohazardcs1.6817 жыл бұрын
Wtf man. You should clean that it in time, not waiting for it to get in that mess. Space around injectors on my 13 years old car is clean like as if it were new.
@sirobb7 жыл бұрын
Sasa Glisic The car in the video isn't mine so why should I clean it?
@amojak6 жыл бұрын
they get in that mess as the injector seal is leaking.. you want to look up "black death" to see a really big mess!