MUST WATCH- From A to Z on injector removal when they are seized - Renault Trafic

0:30 engine crank but no start
2:00 remove heater blower
2:50 remove engine breather
3:30 rusted diesel injectors
3:40 injector connector rubber grommet missing
4:30 remove injector fuel return pipe
4:50 removed rusted injector bolts
5:00 injector bolt shorter than the rest
5:40 remove injector pipes
6:40 set up hydraulic injector puller
7:20 set up hydraulic piston puller
7:35 injector removal action
8:40 seized injector removed
9:20 second injector extracted
10:40 third injector hydraulic removed
11:32 injector connector water ingress
12:00 stuck injector removal
13:00 install injector puller adaptor on the stuck injector
13:15 broken diesel injector in extraction process
13:30 injector broken half way
14:15 cutting new thread
14:40 extract injector sleeve
16:20 clean cylinder head corrosion
16:40 drill broken injector
17:40 extract injector nozzle
18:00 install new injectors
19:04 program injector codes
19:30 install connector rubber seals
20:00 remove wiper panel
20:22 water drains blocked
20:40 water leak on cylinder head
21:20 reseal wiper panel
OGS Mechanics is a specialised garage workshop based in Finchley Central, London, UK, that carries out repairs, maintenance, ADAS calibration, vehicle security upgrades, engine rebuilds, extraction of stuck injectors and glow plugs, advanced coding and programming for almost all vehicles on the road.
The OGS Mechanics workshop is the one-stop for all your vehicle needs!
OGS Mechanics
☎️: 0208 346 6755
📞: 0790 864 0578
📧: [e-mail]
📌Units 9 - 14 Millers Yard, Rear of 28 Long Lane, London N3 2QG
Our website: www.ogsmechanics.com/
More articles about car repairs: www.ogsmechanics.com/blog/
#renault #renaultvan #renaulttrafic #engine #enginecrank #nostart #injector #rustedinjectors #injectorbolts #hydraulicequipment #injectorremoval #wateringress #cylinder #cylinderhead #corrosion #wiperpanel #ogsmechanics #garageworkshop #garage #autorepair #carrepair #carmaintenance #enginerebuild #injectorremoval #adascalibration #coding #programming

[@d-s-ll2378]

This is the most respected mechanic, thanks for showing us the great attitude and professionalism.

[@jonjolliffe7757]

This is the mechanic that has just sorted my injectors on my 2012 Vivaro. He did a fantastic job, My engine head was far worse than this with all bolts very badly corroded. I couldn't get the van to their workshop so they came to the Isle of Wight. My scuttle panel had the the central bolt broken so water just poured straight on top of the engine. It was this Video that made me decide to call them, Good price as well. Thanks

[@patrickpirelli7897]

How much did they charge you ??

[@mksl3894]

Thankyou for you advice .i need my ijct to replace.thanks .

[@kevinpalmer7452]

Superb job gentlemen and an impressive selection of special tools a quality repair indeed.

[@davidharvey8812]

Thank you for posting. I was told by a Machanic that if a fuel injector breaks off the engine is F@@ked. He said if it does he would give me £300 for a traffic on a 53 with 90 thousand miles. 🤷🏽‍♂️ great work guys !! 😊

[@samukbk1475]

These guys are amazing..they done my car when everyone was saying it’s impossible..

[@tracieoliver2307]

These guys are top notch and I can recommend them as they did my van and its run superb ever since!

[@DorinelMusic]

Thanks for the help with silicone repair, the cause of the problem, to this model - BIG LIKE!!!

[@dejanfreighter2926]

You are a genius 👏. What a good narrated, slow & full of detail video.Thank you Sir, helps a lot.

[@michaeldepass7778]

Great demonstration, thanks for taking the time to show us

[@NafanyaZX]

Invaluable detailed explanation of what's going on. Thanks a lot.

[@LifeWorkRestPlay]

Excellent work, very informative & super quality video, thank you.

[@thodoriskimoliatis3003]

Great job! Thanks for detailed explanation.

[@lukaszsosen4266]

Professional job we need more mechanics like that 💪👍👍

[@user-ic7yh2gf1e]

got to say thats the best iv seen grate job done.

[@pantudino14]

Great video! Very useful !

[@Gilespargiter]

That was a very good clear video. Thankyou.

[@BrothersGrim2012]

Great video very helpful 👍👍👍

[@larseivindwelle]

Very good and informative video. Thanks!

[@alank616]

Great video, thanks to you both for sharing

[@viktorbraun5303]

Exellent video and very detailed. Thank you

[@MrMadenuff]

Very informative video, thank you.

[@dax6376]

Very informative, thanks ❤

[@forced-induction]

Really good video. Hydraulic puller ftw

[@everythingeverywhereanyone]

Brilliant video , such hi quality and nicely explained. Was going to buy a vauxhall van but after seeing this I'm unsure.

[@patrickpirelli7897]

I wouldn't ever buy another never 😱

[@jimt8667]

Superb video

[@JoeNunes345]

Thank you for posting this informative video. At around the 12 minute’s mark it was decided not to apply any more pressure, to prevent the top of the injector from snapping off. At what pressure do you decide to stop and change methods? Kind regards, Joe.

[@davidbonnett5441]

Fantastic video.

[@kelleypack1000]

Wow great job

[@frazahmed6168]

What is about the tip of the last injector? Where is it? How did you extract it?

[@dominiknowacki5586]

Hi. Amazing video . What you can do if the washers which keep the injectors cant get out as the bolts completly rusted . Not possible to put any socket.

[@kevinbarnesworship5517]

Thanks for this video. Great help... Do you recommend coating the injectors in copper grease before Installation?

[@michaelbrennan8451]

Excellent video you make it look so easy.i suppose once you have the tools and the head for this type of repair your laughing.

[@anthonyoconnell9389]

Great job well done

[@RD-650]

Well done 👍

[@surfreadjumpsleep]

thanks for the video! Now the trick is to find a garage with this tool.

[@pizzaro4541]

brilliant video thank you

[@BensWorkshop]

I do like your hydraulic lifter, though I made an adaptor to go on my injectors in my Jaguar X type (same as Ford Mondeo MK3) and can then hammer them upwards. Mind you mine get tar seized rather than rusted in.

[@kennethtalbott2233]

great job.

[@GORANRELJANOVIC]

Fantastic job. Coul you be so nice to tel me which drill and thread taps are you using. Thnx very much in advance.

[@lizardking5002]

Hi nate great video. What make is romoval tool please

[@howtolife5705]

Please come to Brighton UK and do this on my van!! 🙏

[@faroukkhan6777]

Excellent tools nice job ,,, Mercedes Benz, Nissan,, Renault's,,, BMW, and so on ,,,, hard to remove,,,, but it's all about vehicles not being maintaining,, like old days,, before,,,💪

[@MrMay141971]

You have done such a great job, but the design of these fuel injectors is really bad and stupid

[@lgtweewielers]

Where to buy this tool , nice work !

[@TM-tz1nx]

Super film!!!!!

[@user-ki5vq1mh3m]

Thanks allot sir

[@Shmbler]

Funny. Two weeks ago I noticed that water is dripping on the head of our Trafic. Looks like I have to remove that panel, too ;-)

[@dootsize]

were did you buy the tool and how much ? cheers paul

[@zambotv8150]

Amazing

[@alvislacitis5019]

2:16 good catch lol

[@boomshakalaka2275]

Great job, did the end of the tip on the 4th injector stayed inside the head? Did I miss anything?

[@OGSMechanics]

The injector nozzle was removed before we pull the lower injector body.

[@tinker-time]

yer good job that hats off 👍👍👍👍👍👍

[@arkaprestige8051]

Need help, My Chevy Cruze petrol, just having rough idle and a lot of white smoke, the mechanic already change the Piston ring, cylinder gasket, but the problem still there, help me diagnose the problem, is it air flow sensor, or bad injector, or bad coil, or bad head gasket? Thanksss

[@MARKH-er5bl]

When you drilled out the broken injector.It looked like part of the injector nozzle was left behind....when you compared it to the other injector it was a lot shorter where the spray nozzle was..how did you retrieve the rest of the nozzle?.

[@Stu-SB]

Fantastic vid, what a piss poor design by the manufacturer, little to no real forethought of water dispersion off the scuttle panel, the engineers should have their arses kicked for creating this problem... EDIT: I've a 2017 Mk3 Trafic and checked each sides drain last night, flowing freely thankfully !

[@cyborg9718]

Good evening can you tell me which drill bit you use to smash the injector at 16:40

[@ezel565]

How much complete puller please uk

[@moffatt43]

Good work but you could help yourself out quite a bit with this particular model by where the water gathers and goes into the injector seats if you squirt loads of WD40 in there for a few days before the vehicle gets into the Garage. The injectors I don’t normally tend to have a problem with,it’s the Glow plugs but they can be assisted in coming out with the same principle of explaining to the customer that they can help by a few weeks before the Job if they can squirt just a little bit of WD40 in the glow plug seats. I also explain to customers the importance of keeping leaf’s and debris out of the location below the windscreen and therefore keeping all the drains clear. The amount of problems that customers have which could be simply avoided if they did some general maintenance on their vehicles is incredible….!. Nowadays with these panoramic sunroofs and people who are not aware that they need to :- 1: Keep the Sunroof rails and drains clear 2: They need to get ( and ask specifically ) for a sunroof service 3: Fuel Filters do not replace themselves ?!!.

[@xxwookey]

plusgas is a much better penetrating release agent than WD40.

[@kat0197]

Where i Can buy this hydraulic piston??

[@brianschneider9067]

How did you extract the remaining portion of the injector nozzle? Clearly a portion of the nozzle was not extracted. How was it facilitated?

[@HamzaHamza-dn2nt]

How we can this same thing

[@ym-imyloi981]

How much would this roughly cost for all 4?

[@mosquitonable]

About 2000 US dollars for 4 brand new injectors. Cheaper if used ones

[@djgomaz1]

Fantastic 👍

[@yensabi]

Had my vivaro injectors and glow plugs done by this company a few years ago , not cheap but they did a great job , it’s a really badly designed engine and scuttle to allow this to happen.... 👍

[@sailingikis]

How much does a work like this costs for a Ducato?

[@robfromga2]

What took is that?

[@piciu256]

Could applying anaerobic sealant at the sleeve prevent this issue altogether?

[@DG-EditsYT]

Probably

[@ferrarigto599]

I use silicone to put on the injector on all lenth...

[@almacsutka4571]

And the engine can run or can't?

[@hot-shotlabel3212]

Where to buy the tool?

[@frederickkwek3772]

I’m just wondering why penetrating fluid is not used to help with the extraction?

[@Hissing-Syd]

Apparently even with penetrating fluid they can still be a real pain to extract, I've heard of all sorts of stuff used, one chap recommended using vinegar to break the corrosion between the head and injectors.

[@garybrown5500]

The injector clearance between the head is so tight with corrosion penetrating fluid would take months to penetrate where it is needed, Much like seized nuts on bolts very rarely do you see the ingress of fluid when the parts are dismantled.

[@martinj9251]

Because clearly it was not needed!!

[@troubledtinkerer]

Do you cut all the seats or just the one that was drilled?

[@FreddysHamster]

Watch the video?

[@martinj9251]

How much for this service,?

[@AfzalKhan-vh3ny]

Can you please add link to buy hydraulic Injector puller

[@shamstar2k]

looks like one they made

[@glennbartlett416]

At 17:48 the bottom part of that tip is missing! Where is it? Did we even see that the engine run ok?

[@niallenglish3777]

gr8 vid and v informative, thanks 4 sharing. This is a job and possible probs I've got coming up now shortly, so have a few Q, 1, after you widened and drilled out the sleeve in order to remove the broken injectoe/nozzle, How'd you sort the sleeve for th next injector to fit into as surely the hole is bigger now, or has a different thread on it. How's that work with th new injector designed for something different? 2, do you always have to enter a new code into system when changing fuel injectors? and if so, How's this done? I don't have a top of th range OBD tool, am planning to upgrade th one I've got, but what capabilities must it have? can we not just order injectors with th same code to suit?

[@nate123123we]

1. You replace the sleeve with the injector. 2. Yes, you do need to put the new calibration code in, its done with a OBD tool.

[@mosquitonable]

Is it safe to use WD40 to loosen rusted injectors?

[@xxwookey]

Yes, but plusgas will work much better.

[@howtolife5705]

Why worry about changing the injectors when it's clearly an electrical problem that can be sorted by cleaning & sealing the contacts & wiring, and fixing the leaking scuttle? The electrical part of the injector is at the top and easily accessed without removal.

[@leekirtley7234]

There are lots of stories of injector removal horror stories and tons of vans for sale with injector problems. Do you think people go at these injector jobs with the wrong gear and no idea?😮😮😮

[@glenfordstobbs1325]

hey where can i get that tool to buy

[@yasintokmak251]

how much km ?

[@jesshowe4591]

How do you get all the bits of rubbish that fall through into the piston out

[@garybrown5500]

Compressed air.

[@fredfly001]

WHY oh Why are you doing this dry, surly it would be better to let the area soak in penatrating oil to help break the dry corrosion, then it may not have snapped ! Not really the way to do it - DRY

[@frederickkwek3772]

I totally agree too....why CRC or WD40 is not used before hand?

[@everythingeverywhereanyone]

I thought same thing , would of definitely helped.

[@tugrulbey3095]

No it does not help. Not even a bit.

[@thatdaftscottishcarguy]

the injectors were corroded all the way down, nothing would break that down and would just be a waste of time

[@JJ-jc8yv]

@@thatdaftscottishcarguy what about freezing injectors and waiting 5 minutes before removal?

[@bboytyby]

Why no wd40?

[@RayBrennan]

This guy didn't curse once! 😂😂

[@clifjonejontilano3578]

Looks easy when i was watching, but im sure its totally different when im the one doing it😂😂

[@stormeagle28]

LOL!! Just wait another year and the injectors will cleanly rust out of the engine.

[@karlavelo2482]

This makes me wonder why Renault invests in Formula 1 when they can't manage to avoid such engine design flaws ...

[@stevenbean9706]

mine broke right in half

[@howtolife5705]

Why pull them out raw, no pretreatment with penetrating fluid? That's brutal. That last one snapping could've been avoided!

[@lancepage4840]

No new pipes !!!

[@tonyclack5901]

Thats not seized. When the bolts snap off of the injector clamp then you know the injectors will be properly seized.

[@garrysouthern1439]

where abouts are you

[@themagpie_1]

that is the Nissan engine. I have the Renault engine F9Q in my Vivaro. such a better engine to work on. i`ll never sell my 2005.

[@peternewman3487]

There is no excuse for water ingress like that whatsoever.

[@howtolife5705]

Tell that to Renault/Vauxhall. They should be in court for this

[@chrismills9346]

Load crap engines chain snap on them too stay well away from them

[@user-tn1hk6zm2f]

All this new designed stuff is junk.

[@barongreenbackthe2nd418]

I need my 2.5 vivaro injectors removing,I live in Devon please help me.

[@lordvonzipstor5304]

Hey mate, I have used basically the same system however it is fully mechanical, the rod spins with a 24mm spanner on my 2.0 dci Trafic after a 24h bath in super lubricant and the thread literrally came out, have a look here photos.app.goo.gl/KiA6CQoakSS1ZRv88 Unsure if I should try the same on the others or if I just should forget about this operation, continuing to drive the vehicle on 3 legs. Let me know, cheers mate.