Just went through with the install, everything went great and screen now works. Only downside to replacing the screen, you will have to physically transfer everything from the old screen to the new one like shown. It is time consuming and is more complicated than some other phones like the Iphones. A few tips for people doing this replacement: Definitely use a heat gun. There is a lot of adhesive holding down the ribbon cables, heating up the screen side where the cable is located for a couple seconds loosens it up quite a bit. The ribbon cables are very fragile and can tear easily. Remove the battery with extreme caution, you don't want to puncture the battery at any time. Try to keep the battery flat as possible when lifting it off, bending the battery can cause damage and potential puncture. Piercing these batteries will cause them to ignite and burn. (Happened to me before) Some replacement screens don't come with the volume and power buttons attached. You can reuse your old buttons by removing them from the inside with a paper clip. There will be 2 pieces, a white rubber piece and the button itself. Install the tiny rubber piece first then press the black button in place.
@pronoob32405 жыл бұрын
VDub In Paradise how is this simpler than repairing an iPhone screen? Have you ever seen one done? All it is is 7 screws dude😂. Two on bottom, then you take a suction cup on screen, lift, separate adhesive unscrew the cover over lcd cables disconnect then connect new screen and reverse. It’s a 10 minute job this is like a 40
@VdubInParadise5 жыл бұрын
ProNoob ProNoob ProNoob my mistake I put “less complicated” than “more complicated” 🤦♂️ I’ve done iPhone screens myself it is easier. This phone required the entire motherboard being transferred vs just a screen.
@sniffles86555 жыл бұрын
Thank you! One extra thing for anyone that orders screen and frame off ebay, you have to remove the buttons from the old phone frame and replace into the new frame, just poke them out from the inside with the little tool that you use to remove the sim card. Be careful though, there are tiny itty bitty rubber spacers in between the button and frame, you must pull those out too and put into new frame.
@coupondrake11285 жыл бұрын
Well dam I guess I won’t be fixing my phone after seeing this video!
@shermkeys5 жыл бұрын
I did this is was not as hard as it looks the only problem is the new assembly screen keep flashing and freezing so Im going to try to figure it out or buy another one anyway if you dont feel comfortable doing it take it to the pros because you definitley need a little knowledge when taking this apart or you could ruin your phone.
@alexlucio46095 жыл бұрын
@@shermkeys what the original rice to take ur phone to a professional
@heribertosanchez46645 жыл бұрын
😂😂😂 gotta buy a new one
@bap13285 жыл бұрын
Exactly!
@HWolfe4 жыл бұрын
Obtain a throw away or 'dead' as a door nail smartphone from eBay...then watch vids here. I have been tearing down phones now for 12 years. Learned just that way. I rebuild phones & computers for people gratis who are poor. Or elderly. I am a SW specialist some hardware as well. BTW I am 68 years you ng.I am not missing a beat. Ok .being Mensa comes in handy after all. Not boasting but it helps me enjoy learning new skills. Now if I can just master Japanese.🧐 Didn't make me filty rich dangit. Ok...get parts online as well and check out ifixit.com as well ...good luck.
@2012TheAndromeda4 жыл бұрын
Things that keep the phone together: 10% screws, 90% adhesives. .. .. .
@kodybaker84993 жыл бұрын
I guess it is pretty randomly asking but does anybody know of a good website to watch new movies online ?
@elianrocco23573 жыл бұрын
@Kody Baker Ehh I use Flixportal. Just search on google after it:P -elian
@kodybaker84993 жыл бұрын
@Elian Rocco Thanks, I signed up and it seems like a nice service =) Appreciate it!!
@elianrocco23573 жыл бұрын
@Kody Baker Glad I could help :)
@johnf89914 жыл бұрын
***REPAIR ADVICE: My purchased phone case was missing the volume and power buttons and mini rubber plungers which I had to remove from the old phone case and replace in the new phone case. Check EVERYTHING before you seal it back up! Serg Tech: Thank you for this Excellent Video!
@jpjp91114 жыл бұрын
Glad you took out all those little parts. I wondered why my part looked different.
@ghaziterbela6 жыл бұрын
Change title to stylo 4 tear down
@charleslane27356 жыл бұрын
no
@mosmith91875 жыл бұрын
Please dedicate a video of battery replacememt of LG 4 stylos.
@Amariyo_03 ай бұрын
So my phone cracked a while back, probably mid 2019, just bought a new phone instead of fixing it, I decided to try and fix it 2 weeks ago, ordered the replacement and whatnot, felt like I was doing surgery, needed all the patience in the world to pull it off, but in glad to say I did it 😭
@cedricgriss60505 жыл бұрын
Liked the video - very helpful. Would prefer to see the re-assembly in real time (not 8X) since this has a lot of parts and it would be easy (huge risk) to make a mistake. The fast put it back together is a mistake spoiling a great video.
@madebymago4 жыл бұрын
excellent tutorial, I just fixed my Stylo 4 plus with this video
@ConstantDistres55 жыл бұрын
Thank you so much! Today my phones screen broke beyond bearable and this fixed it! Liked :)
@jesussalazar66584 жыл бұрын
You muay have a good memory and patience and abitlity beyond normal lmao
@MizCo-zt8vt5 жыл бұрын
After seeing this $70 is not that exensive after all. I relized this is too complex for me after you remove the 4th connector piece.
@tedleach25263 жыл бұрын
A good video, very helpful, but missing 3 things... remove/replace the power button; remove/replace the volume buttons; and remove the stylus cover during disassembly.
@OlivierGandou4 жыл бұрын
Is this part compatible with the Stylo 4 plus? Q710WA. Having some issues locating the right part here... thanks.
@ryanjames57995 жыл бұрын
Great only one problem! This is a "Screen Replacement" Video not a "LCD Assembly and Screen" Video!
@ightimmaheadout52704 жыл бұрын
Just do the reverse of what he’s doing bro
@Dylan-kz6jt5 жыл бұрын
This my friend is a surgery.
@PhantomDragonEternal4 жыл бұрын
Screw this whole process. If I knew it would be this much of a pain in the ass, I would have just bought a goddamn otter box for it.
@lordofwar13972 жыл бұрын
Can you take apart a Galaxy View 18 inch tablet apart ? my battery in it is dead just saw how careful you did on this one . thx
@hectorrivera21724 жыл бұрын
Hi Serg . Do you know wheres the gps connectors at?
@richyrich77955 жыл бұрын
The only thing missing is to replace the stylus housing with clip and bushing. And to replace the side power and volume buttons onto the new frame. Most new frames don't come with those already attached.
@richyrich77955 жыл бұрын
Sorry for the late response. The buttons come off fairly easy. I used the SIM card pin to pop off the buttons from the inside of the housing. Make sure you get the very small white rubber bushing too. Without that, and the buttons won't be pressable. I hope this helps.
@carleadie60224 жыл бұрын
Great video but you never showed how to replace the glass screen.
@JointVencha3 жыл бұрын
Bro everything he's taking off is the screen that whole part is the screen you can buy that part
@limpgrandma5 жыл бұрын
Instrucions unclear. Phone is torn in half, in the trashcan.
@johnscott33705 жыл бұрын
Bro. Save the adhesives so you can close it up correctly? WhoTF reuses adhesive? In any application? I think I will go the extra mile, spend a dollar or two and spring for new adhesive. Also in the very beginning you asked viewers to hit the like button. How do I know It's not gonna suck? It didn't. Nice job, thank-you. Question about the hot plate. Is the temperature variable and if so what temperature do you set it at? In another video I watched they injected isopropyl alcohol using a syringe and a needle around the perimeter of the battery. It looks like it dissolved that glue without applying any heat. Thanks again. I did like&subscribe. I had a little bit of time to kill and I learn something and I got to break your balls a little bit.Wish me luck I just picked up the parts to fix mine...
@AlejandroGomez-wc2fd Жыл бұрын
ty for the detail tear down
@oddity46504 жыл бұрын
Could u list the names of them pryjng tools as I have no idea what tha red one is
@luciano18195 жыл бұрын
Same screen for the different versions of the stylo 4 or not compatible ?
@genenorton28804 жыл бұрын
my swap was even harder I had to transfer the actual buttons and the stylus compartment cover and a plastic part in the camera compartment.... also the tape over the screen cable at the bottom..... anyway thanks for the good instructions.
@michaelmcgregor32523 жыл бұрын
Very informative video basically you just got to take your time I can do this thank you
@4PORSH9444 жыл бұрын
Dang!! they even glued in the darn battery. I guess that I will be visiting a Mall tech. Patience is needed with this repair.
@bobbygordenakaredneckbilly38566 жыл бұрын
Thanks for the video. My screen and frame came with the Power and volume switches as well as the earphone jack and ear speaker and vibrator motor.
@marcarft86966 жыл бұрын
where did you buy the screen?
@sopachinahot70446 жыл бұрын
Where you buy it
@sArCkSsSs6 жыл бұрын
Tell uuusssss ...where did you buy it??
@bobbygordenakaredneckbilly38566 жыл бұрын
@@marcarft8696 ebay digitalhome123
@damndoor35705 жыл бұрын
Bro you got a whole new phone tf
@PghNGDave313 жыл бұрын
Ha! You did everything except what the title says. Replace the glass. Unclear on how the glass is COMPLETELY removed.
@robertson1064 жыл бұрын
Just replaced the digitizer on my son's LG Stylo 5. I purchased from Amazon. It was the same Model as the one for Sprint. Only need to go as far as 5:17 in the teardown video for the replacement item from Amazon. I noticed a couple of things not in the video, but all pretty straightforward. Tiny Speaker Cover from the front glass to go back in first to digitizer unit and the fabric like tape to secure the digitizer wiring back in place once reinstalling. So save everything until done. Also, only 13 screws. Heat is a huge MUST. Everything is heat sensitive adhesive. the more heat the easier to remove!!!! and reinstall to be secure!! item is www.amazon.com/gp/product/B07ZJL7FY9/ref=ppx_yo_dt_b_asin_title_o03_s01?ie=UTF8&psc=1&pldnSite=1
@get11net5 жыл бұрын
Thank you for the video! My loud speaker went flying out too lol
@madebymago4 жыл бұрын
Is this the same screen as the Stylo 4 plus?
@MA-jx6in5 жыл бұрын
Why I like my Stylo 2 fone I been thru 2 batteries but I can remove then in 30 seconds and replace them
@SHONDA09744 жыл бұрын
Great video!!!BUT I'd rather pay for the fix 🙃🙃🙃🤙🏾
@luarmedieval16766 жыл бұрын
Make a video on how to replace just the outer glass screen !!!!
@ashleynicole40645 жыл бұрын
where is link for screen please ?
@PlatinumViperAH4 жыл бұрын
What I did was buy another phone that's locked or something in good condition and just swap the motherboards, much easier
@laverdadesmejor2 жыл бұрын
What about resealing the back cover ????
@javad7885 жыл бұрын
Thank you!! Seriously helped!
@tenncoin5 жыл бұрын
I bought a screen with frame but it doesn't have the side volume and power buttons. Do you know how to remove the old buttons?
@NinjaWagz5 жыл бұрын
JUST happened to me too... If you use one of the tiny screw drivers, you can PUSH them out, BUT BEWARE. THERE IS A TINY PIN IN BETWEEN THE BUTTON AND TO "IGNITE" THE SIGNAL
@tenncoin5 жыл бұрын
@@NinjaWagz I used a thumbtack to unlock the buttons in the old frame. there's little holes at each end of the buttons on the top side of the frame and yes the tiny pins like to fly away when you use tweezers to insert then in the new frame.
@mikeadams54323 жыл бұрын
Did i miss something. I seem him rage apart the whole phone,but never seen him replace the screen.
@lisasaults4 жыл бұрын
Howndo i know id i need to replace the whole screen and digitizer or if i can just replace the front glass
@imnotfrfrr5 жыл бұрын
So the rubber is sopose to stop water fron geting in. Does that mean its water resistant? I heard that it ws ip 67 water and dust resistant but im not surr
@mosmith91875 жыл бұрын
Would you show how to replace the battery from a LG stylos 4 .
@ljessecusterl5 жыл бұрын
Good video. Looks about the same as doing any other LG LCD with the frame. Thanks, Serg!
@davidpadron33456 жыл бұрын
Can you pleaae give me the link for the screen? I really need it..
@gavingavin25955 жыл бұрын
contact me
@edisongaoiran96283 жыл бұрын
how to remove the power and volume buttons sir?
@bichounitec4 жыл бұрын
Alguien usa tus videos y le pone audio diferente. Sabes si hay alguna batería con mayor capacidad para el LG Q stylus plus?
@oddity46504 жыл бұрын
Hot place machine for repairs link item is not there
@exoticnerve34105 жыл бұрын
HELLOOO STILL WAITING ON TGE LINK BELOW FOR WHERE TO BUY THE SCREEN REPLACEMENT WITH FRAME!!!!
I guess I'm going to a professional. Bc if they F my ishh up they can buy me a new one! Lol
@soapzsudz5 жыл бұрын
How do you do this but like not with the LCD stuff
@YouDontKnowMe210tx8 ай бұрын
The links to these products are expired. The tool repair kit is expired.
@jheelanid66364 жыл бұрын
So what is wrong if after you complete this whole process and the screen is flickering? It powers on just fine, but after I lock it with the power button and unlock it, the screen flickers.
@cesarazael75 жыл бұрын
Do u have a link where I can buy the screen???
@Josemendoza-mf6ot5 жыл бұрын
You can order on amazon
@TheJames-Edward5 жыл бұрын
Doesn't look like something I'd want to do I'd probably screw the whole thing up.
@TheBusFoamer5 жыл бұрын
James Steevens I’m 12 and I did this it’s easy
@ConstantDistres55 жыл бұрын
It's easy, just did it and everything went smoothly
@TheBusFoamer5 жыл бұрын
David Perea yea
@YOUNGCHRISWORLD5 жыл бұрын
I'll prefer to let the professionals fix my screen instead... Excellent video 💪👊🙌
@seetheforest4 жыл бұрын
Great video! I'm just going to buy a new phone..
@mauriciovasquezrivera11895 жыл бұрын
Hi I have a question as I can change the button of/on my LG Stylo 4 as it Dell and I did not realizó thanks . I wait your answer
@kc2sho3 жыл бұрын
Add some heat and those adhesives will give more easily, I cringe at all the prying without heat. Also that back cover will need new adhesive, used adhesive doesn't reattach.
@marcorubio34966 жыл бұрын
No wonder they say the battery is non replaceable. They even have adhesive. These phones are like disposable. It probably cost the same as a new phone to replace the screen.
@killer2055686 жыл бұрын
it actually does cost the same for a new phone xd
@richiermarte64185 жыл бұрын
No, the cost of the screen on amazon is 50.38 dollars.
@uptGuapo5 жыл бұрын
Lol just about. I have to get my screen replaced. Accidently left it on the roof of my car and drove away. Back tracked and found it in the road burning up from the sun and possibly heat from tires. Im guessing it got ran over by a vehicle since I just have spreaded ink only in the middle of the screen aligned where the pop socket is. The popsocket is bent like it was ran over. The phone is still intacted. No scratches, no dents, bends, nor cracks. Phone still looks brand spankin new lol. My screen just have ink all over the middle, and spreading slowly. $120 for screen replacement 😩
@aidanparris50095 жыл бұрын
On ebay 29.99
@mjrgaming62315 жыл бұрын
@@uptGuapo the screen is not that much though. If you did it yourself it wouldn't have cost more than $40.
@genericusername55205 жыл бұрын
Is this screen supposed to be sharply pixelated?.mine has a lot of jaggirs.
@TheBusFoamer5 жыл бұрын
Generic Username no u prob got a faulty screen
@stephenlouden4805 жыл бұрын
If you do this please know your phone is no longer water resistant! ..or warrantied. Just pay the 5 to 7$ a month for insurance in case your screen cracks or phone breaks. I have stylo 4+ and don't care if it breaks because it was only 150$! Loving it for the price can't beat 16mp camera and 3gig memory.
@marinmarin81995 жыл бұрын
This phone was never water resistant...wtf you talking about
@stephenlouden4805 жыл бұрын
@@marinmarin8199 Yes before he took apart the stylo 4 it absolutely was water proof ip68. You can look that up. After a screen replacement it is nearly impossible to ensure moisture will be kept out.
@ljessecusterl5 жыл бұрын
And when it's broken, it's not warrantied or waterproof either, so your point is...?
@nvro33775 жыл бұрын
3 gig memory? It's has 32gb storage and 3 gigs of RAM
@madisonfick73615 жыл бұрын
cool, now all i need to know is where to get the screen
@aylengomez25934 жыл бұрын
Hola a este vídeo le hiso falta mencionar cuando se cambian los botones del celular que tienen una piesecita suelta tan pequeña, que se confunde con basura del pegamento y que la pueden tirar como yo y es difícil encontrarla si saben quién la vende me avisan por favor
@kris.ast3r9325 жыл бұрын
Things you did not show here STYLUS cover and button, camera clip, Volume buttons. These all needed to be transfered from the old broken frame to the new one.
@jerometaylor93744 жыл бұрын
Volume Buttons just use a small pin on the whole sitting on top of the volume buttons.. Then push the white foam out the phone...
@josh-dj7vs6 жыл бұрын
its a plastic razor blade not a prying tool
@ericevans73046 жыл бұрын
yes it is a prying tool. look it up smart one lol
@randydillabough34695 жыл бұрын
This was a good video but I don't get why you don't show us how to put it back together in normal speed that's a big part of it!
@jadonwilliams83685 жыл бұрын
If you go to the settings of the video you can set the speed to .25x if you can't see how to go backwards
@randydillabough34695 жыл бұрын
@@jadonwilliams8368 thats not the point!!!! 💯
@jadonwilliams83685 жыл бұрын
Oh ._.
@kamalsunar10552 жыл бұрын
Hayu mach price
@ericevans73046 жыл бұрын
my phone isnt broken, just need a nice video so i can know how to it it does break
@farooqtecnical92125 жыл бұрын
lg stylo2 tarminal repaiar lines lines khrab ho jay to kaysay theak karay pleas share avideo
@Clamjammer5 жыл бұрын
Derka derka derka
@yingm885 жыл бұрын
I had replace I phone 5, 6, 7 screen before, after seeing this video, just buy a new phone too complicated than I phone. I like my stylio.
@machdaddy94 жыл бұрын
You forget to mention to take out the actual buttons on the assembled screen.
@michaelfryback15645 жыл бұрын
thanks for video where is the hard drive located
@pronoob32405 жыл бұрын
Michael Fryback Hardrive is not replaceable it is built into motherboard
@williampaulk42895 жыл бұрын
Forget about it. Ill be paying someone to fix my screen. Too many parts.
@TheBusFoamer5 жыл бұрын
william paulk it’s easier than it looks I’m 12 yrs old and I did this it’s really easy if u know what ur doing
@angm11533 жыл бұрын
It's a great video until he speeds up the "replace everything" part. I can't remember the order he removed the parts in. Hoping I can find a video that shows me how it goes back together.
@ronaldthepeculiar11114 жыл бұрын
better off buying another phone. looks like they made it to throw away after something breaks lol by how much the screen costs for 50 to 70 more bucks you can get the newer stylo5 one at walmart for $129.00. but good video to show everyone how it works
@jean-carlocolon42816 жыл бұрын
You didn’t show me how to change the screen. All you did was tear apart the phone. Now I have pieces of the phone but still no screen
@dmforeacre5 жыл бұрын
Replacing the screen in frame is really the only way to replace the screen on this phone.
@briangodby69265 жыл бұрын
This repair works fine with this screen, you have to make sure u get the one with the frame to save u a couple hours. www.amazon.com/gp/product/B07G721XFG/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
@MaGeeVer4205 жыл бұрын
Why havent ANY OF YOU WANNABE TECHS showed the POWER & VOLUME BUTTON REMOVAL because tour new frame dont come with those, at least not through ebay. I mean the outer push buttons you haveto dig around in the 2 litle openings by the power button and 3 at the volume rocker
@xaxis92295 жыл бұрын
what do I do if some of the screws are stuck!
@gavingavin25955 жыл бұрын
buy a now phone
@xaxis92295 жыл бұрын
@@gavingavin2595 *new and Nah I figured out how to remove them.
@ja19454 жыл бұрын
rip my audio connecter, it broke in half.
@ltaylor2238 Жыл бұрын
maybe you should place the camera so we can actually see what you are doing!
@brucelloyd18534 жыл бұрын
A couple of important missing things in this video. For one he did not show removing and replacing the bracket for the stylo pen. The most important part was that he did not show the the on/off button and the volume control buttons had to be replaced. But that was a real hassle because there are extremely small little pegs that have to be switched out to make the buttons work. Be very careful to watch which ways these pegs go in. If you get them wrong then the buttons don't work.
@1689solas5 жыл бұрын
Well I guess I'll be buying a new phone.
@michellelongoriasalazar67884 жыл бұрын
Hola
@rubencervantes58403 жыл бұрын
Yea , very simple , for people who knows how to do it 💀
@MizCo-zt8vt5 жыл бұрын
So you took apart the phone but did notnexplain how to change the screen. I guess im buying a new phone...
@joemolinas80413 жыл бұрын
Damm that seems like a lot of work
@PastorCascante4 жыл бұрын
13 not 14 screws.
@ghostraven26334 жыл бұрын
Yeaaa, I'm not doing all this.
@noeliajaime76564 жыл бұрын
I need to only cjange The display, not The screen though...
@Dirtbillys5 жыл бұрын
In columbus in. people want 129.00 to do this. Guess ill throw my 6 month old phone away! How sad!
@lissacampbell485 жыл бұрын
Ummm this wasnt for a screen replacement
@dmforeacre5 жыл бұрын
Replacing the screen in frame is really the only way to replace the screen on this phone.
@prestondavis77194 жыл бұрын
Didn’t help😡
@fyodor80084 жыл бұрын
Your video is very high quality yet I did not like it for one reason: IT DOES NOT MATCH ITS TITLE. You included the word "glass" in the video, and your video popped up as the first hit when I queried youtube for "lg stylo 4 glass only replacement". The reason I'm butthurt about this is because I fucked up when buying my screen and I did not buy the digitizer. My digitizer is functional and I want to recycle it while swapping the glass and this video offers no insight into how to do that. Otherwise swapping the glass with the digitizer already put on it is quite easy.