Setting your servos at zero blade 300x

[@timhiggins2445]

THANK YOU! I struggled after a replaced servo going through the beast x manual over and over again, I got confused and thought digital servos, must be electronically corrected and not physically... I went crazy till I found this, now I fly happily again!

[@peterbengel3627]

Thanks for posting this! It saved the day for me. Hero!

[@75018william]

Menu G in beast X can be use to subtrim the servo. It will give you a perfect 90 degre after the mechanical set up

[@nartac2012]

great video but just a tip on safety, I suggest to disconnect at least 2 motor connectors off from the ESC whenever you do any service to your heli. This way, there is no way the motor will start and cause injury. TH is a good tip but certainly is not safest.

[@boyetquinto5269]

it works! my blade 300 is now hovering smoothly. mahalo bro!!

[@slargo83]

You do need to make sure that each of the 3 swashplate links are on the same hole on each servo. Probably not gonna cause a huge difference but the leverage on each servo would be different if they're not in the same hole.

[@1Keymaker]

Those stock servos are pretty crappy lol, I used to rebuild mine all the time also. The only one that doesn't stripped is the rudder but it burns out. Thank god I found a good soul one helifreak that sold me some MKS92a+ for cyclic and a MKS95i for the rudder for about $150. I can't count how many times I have had to rebuild the whole heli but no more servo issues here.

[@Thejasond1979]

Great vid thanks for the help

[@96789jcady]

You should re-setup your beastx after mechanically centering your servos. Re-setup for electrically centered, and travel to avould binding.

[@695look]

Are you using the stock servos? I've had my 300x for a month now, two of the servos went bad right away but were warrantied by HH. They seem to be working fine now but I was wondering if there is a suitable metal gear replacement. Thanks...Barney

[@jhlozada]

Good Vid!!! 450 x swash plate leveling? Pitch adjust and collective pitch!! That would be helpfull!

[@K-B-C]

what you just explained should be preformed through menu point G on the AR7200 after each crash to make sure that the connecting rods have not jumped threads and changed lengths. menu point G will automatically center the servos for you, then level your swash.

[@muhibahasan3737]

Kelton Brooks

[@richard21153]

Good video!

[@magicjoe99]

Can you use the transmitter sub-trim to make small adjustments to the servo centering? Is this allowed with the beast controller?

[@CoolUsagi]

Thanks for the video. After swapping the servos, do you need to re-setup the end point of the servo with the beastX to make sure it is not binding?

[@marvinvanlaviere716]

Hi nice video, Where did you get the metal rotorhead? grz.marvin

[@metalwizard23]

umm when you mid stick doesnt the beast x try and take over if you move the heli?? so you need to be mid stick and on a flat and level surface??

[@strykerqace]

Tail servo on my 300x will not respond to input or gyro when heli is energized. I manually move the tail blades and servo gears are smooth. What failed?

[@loganverdugo9603]

Hey I have a blade 300x. I’m new to the game it has almost everything upgraded to carbon fiber (the blades, the tail rod, and back blade). I don’t really know anything about it but when I touch the throttle at all, the whole helicopter starts to shake violently, to the point it will fall over. I removed the blades and it doesn’t shake at all with them off. Any suggestions?

[@96789jcady]

your blades may not be balanced well together. the blades have to be a matching set. Sounds like your setup is to rigid. Depending on the flight controller you may have to high of P and I gains if you are using the AS3X flight controller. If you are using a different flight controller your gains may still be too high. But sounds like its because of a mismatched pair of CF blades.

[@96789jcady]

Thanks for the tip

[@magicjoe99]

Don't you have to center the pot shaft before you put the final gear on? The pot center is how the servo knows that the servo is centered

[@leecarsonhayler]

Really you want to unplug your main motor from the ESC for safety. Its easy to knock the throttle hold off.

[@96789jcady]

The tiny motor in your servo probably failed. Or the circuit board inside the servo that controls the motor may have fried.

[@96789jcady]

Still stock servos. I just keep rebuilding them