Setup and configure a CANBus GPS in Mission Planner: Here4 setup guide

[@lastry4you]

Thanks really saved me !

[@JDDupuy]

This was a timely video. Just pulled out my units last night and was going to start settin g up and learning. Outstanding! Thank you 3DXR!

[@WyoDevil]

New to drones. Love this step by step guide on pixhawk. I'm confused on how you would set up a gimbal/camera system. Might make for a informative video in the series. Thanks again for the content.

[@sharathkumarsampangi5332]

Finally we have here4

[@Painless360]

This video had been on the channel ready to release for ages. You're not using the playlists are you? ;)

[@MCsCreations]

Thanks a bunch for all the info, Lee and Ben! 😊 Stay safe there with your families! 🖖😊 And happy holidays!

[@RCDUDEFPV]

Great info from the best, Thumbs up

[@motivecrew138]

Thank you for the video. this is really helpful

[@thisisMilindRaj]

I have thanked you with my respect. ❤ I need some assistance. My tether drone spinned 360° yaw, a havoc fast yaw. Upon checking the Ardupilot log, I noticed that yaw command was given to the drone from my SIYI MK15, but I never did that. I use 2 of these same GPS. Quick setup I use: 1. Tmotors 4006 380kv 2. X8 SETUP 3. SIYI ZR10 camera with SIYI MK15 TX 4. Tethered system (Elistair 70 meter) Drone gave some jerks and twitches. Please help.

[@Painless360]

If Ardupilot recorded a YAW command, then I'd check the radio setup and calibration, failsafe settings as step one.. Check out my last build - kzbin.info/aero/PLYsWjANuAm4rXSCRfiZkpuBmUP0u-lLby - to see how I build them here... Best of luck

[@mascot62110]

Bonjour et merci pour toutes vos vidéos ,je possède un pixhawk 2.4.8 est-ce compatible avec ce contrôleur de vol ?

[@Painless360]

Le Pixhawk que vous utilisez est le contrôleur de vol. Pour les « Pixhawks » plus anciens, il existe généralement des unités GPS/Boussole plus abordables. Bonne chance.

[@mascot62110]

@@Painless360 Merci pour votre réponse rapide

[@omjaiswal8750]

Is it compatible with Here+ base station module or Ardusimple RTK starter kit for RTK setup??

[@Painless360]

I have limited experience with RTK. See my videos on it. I'd ask this question to the reseller you'll buy it from... best of luck

[@aguanut]

Why two cables on the Here4? I noticed you connected the blue cable to the CAN port. Are they both CAN cables? Sorry, I can't find any mention of this in the Here4 documentation...

[@Painless360]

At what point in the video?

[@aguanut]

I found it in the documentation: Pinout: CAN x2（Current firmware only supports CAN1-green、blue、white、grey） I found it by reviewing the Here3 documentation which made this more clear, but used the other harness for CAN1.

[@gauravkasar2710]

Is there any improvements in terms of positional accuracy as compared to Here 3+?

[@Painless360]

This contains an F9P, the P stands for the extra precision. The Here 3+ has an M8P inside. The F9P with a dual-band antenna provides a very large reduction in both altitude drift and horizontal drift over a single band M8P

[@ebjamville]

Thanks

[@olacarpe6676]

Hello, thank you for this great video. I have a question did you use the here 4 with its flight controller? I wanted to buy one to install in a bait boat but I couldn't find any videos to see if it's worth it and if it works well.

[@Painless360]

It isn't yet supported. I'll be making a video on it when it is... Happy flying

[@olacarpe6676]

@@Painless360 thank you very much for your super quick response.😉

[@technicalsupport6983]

Want to see what electronics hardwire inside this Here gps 😅

[@k4x4map46]

nice!!!

[@thisisMilindRaj]

Thanks