Bravo relja, fantastican si, za sve preporuke, ima li sanse da te kontatiram, Srbija nam je u problemu sa bike serviserima ali skroz!
@BikeGremlinUS3 ай бұрын
Pozdrav, Na bikegremlin.net forumu postoji kontakt forma. www.bikegremlin.net/misc/contact
@clubtouge10528 күн бұрын
no issues with my freehub but i have bent the axle just where you pointed out
@olieko3 ай бұрын
I think it would be cool to see you guys do the Cape Epic at some point
@dennisduran85003 ай бұрын
I hate loud hubs. I wish the Onyx silent hubs were affordable.
@romanmentor92383 ай бұрын
I have a 6 speed freewheel,the thing is that under load especially uphill the mountain it skips.I think it's not about derailleur or worn chain,when I serviced bearings of a freewheel I noticed the pawls come back slowly after being pressed.Is it possible to strengthen that spring ring somehow or just replace a freewheel
@BikeGremlinUS3 ай бұрын
Please use the bikegremlin.net forum for any technical questions.
@heksogen47883 ай бұрын
Since i've invested in press bearing and puller i can't imagine servicing cup and cone/standard shimano bearing hubs. I hate messing with bearing balls and setting preload.
@MikhaelHausgeist3 ай бұрын
I've get it about teeth of this freehub, but definitely miss about support on a shaft. I've seen two bearings in body of hub and two in a actual freewheel part. Or problem is that there was fill bearings and than was installed cartlidge bearings so actual fill bearings don't give enough support in stock part?
@BikeGremlinUS3 ай бұрын
Good question - that's something that even some great mechanics don't understand. I answered it on the forum: www.bikegremlin.net/threads/shimano-fh-mt410-b-12-speed-microspline-freehub-design-discussion.341/
@markosabljak71343 ай бұрын
It is nice to see shimano started using sealed bearings. Standard sizes are easy to source. What affordable hub do you recommend for ebike? 148 boost, HG body.
@BikeGremlinUS3 ай бұрын
No idea - not sure which hubs are designed to take the extra weight and torque (if any). Shimano Deore (the original, not the Deore XT) used to be their most durable/robust set that doesn't cost an arm and a leg, but they've switched to the cartridge bearings and design similar to the hub shown in the video (with a hyperglide mounting option AFAIK).
@markosabljak71343 ай бұрын
@@BikeGremlinUS Well said. If any. I do not have any objections to current models. As long as they are repairable and not expensive to fix.
@rosomak82443 ай бұрын
Mid drive or back wheel motor?
@rosomak82443 ай бұрын
CUES is supposed to be suitable for e-bikes. I would simply go the route of the least money: 5 or less row freewheel. At least the chain will be far sturdier.
@markosabljak71343 ай бұрын
@@rosomak8244 Mid drive. Back wheel motor does not overload freehub body.
@_kicaBo_3 ай бұрын
Finally a little stuffing and grease on the fingers :)
@rosomak82443 ай бұрын
Modern bike tech design seems to suffer more and more from a disease i call CADiosis - far too complicated parts for what they are and far too many tinny little details all over the place.
@johndef50753 ай бұрын
Though heavier this is a better design than my XT hub which has been making weird noises.
@chrisregister80213 ай бұрын
Do you think a traditional free hub is stronger?
@BikeGremlinUS3 ай бұрын
Cup and cone bearing freehubs have a better bearing support for the axle. Freehub ratchet and pawls - that has been made with 3 or 4 pawls for decades as far as I know.
@rosomak82443 ай бұрын
Typically yes. Mainly for the simple reason that the engagement diameter is much bigger than in the case of a freehub. The forces engaging are therefore proportionally smaller. Additionally they are made from simply steel instead of some fancy aluminium compound. However those days the production quality of freewheels tend to be much lower and you may draw one that is really shabby.
@hakijakurdic65093 ай бұрын
Pozdrav, imam promblem sa zadnjim točkom kada stegnem osovinu otvara mi se točak. Šta bi moglo biti
@BikeGremlinUS3 ай бұрын
Za sva tehnička pitanja bih uputio na bikegremlin.net forum.
@capitalisticsocialist3 ай бұрын
Are you from Bosnia or Croatia? I can hear it on your accent
@BikeGremlinUS3 ай бұрын
Worse! :) It’s all on my channel’s about page. :)
@capitalisticsocialist3 ай бұрын
@@BikeGremlinUS Mogao sam cuti da si negdje od dole! Volim tvoje videos 😁👍🏼
@robertmcfadyen91563 ай бұрын
I was given six of these by a client for payment of completed repairs .