Should I Buy a CNC with a Vacuum Table? || How a Vacuum CNC Works

Рет қаралды 14,031

Күн бұрын

In this video, I go in deep on vacuum tables for CNC machines. How do they work? Every wonder? We look at the full physics behind how they work and what you can do to control your table for the most efficiency and save the most money. Its all about controlling the airflow. There are many ways to control the air so your pieces are held tight and you dont loose money on wasted material. A good spoilboard is key and then its all about thinking how air moves. I hope this video helped you understand it a little more and can save you a lot of money on material or even on buying your next CNC machine.
Allstar CNC: allstarcnc.com/
Discount code for 10% off all their products!: statedwoods 10
‪@ALLSTARCNCPRODUCTS‬
Phantom CNC Systems:
www.phantomcnc...
Email me if your interested in a machine.
Email: nick@phantomcncsystems.com
‪@phantomcncsystems‬
Features:
Gattis Specialty Services
@gattisspecialtysvc1
Follow along with us on:
Instagram: / statedwoods
Tiktok: / statedwoods
www.statedwoods.com
Email: statedwoods@gmail.com

Пікірлер: 33

@AirWeights 9 ай бұрын

Awesome video! Excellent overview of how vacuum tables work!

@Statedwoods 9 ай бұрын

Thanks for that. I hope it helped!

@brokenleadwoodworks 10 ай бұрын

Very informative video. Thanks for sharing.

@Statedwoods 10 ай бұрын

Thanks so much!

@seanmichael5751 2 ай бұрын

i built one for my 4x8 millright and one for one of my shapeoko 3XXLs and they work great. the bigger one is a lot of maintenende and has a lot of limits. the small one has one rule. use a board close to the size of the table and it wont budge

@Statedwoods 2 ай бұрын

Yea exactly. Cover the whole table and problems usually go away. Thats awesome.

@ggsggo 5 ай бұрын

i enjoy your videos and if you are not an engineer you have a good head for anergy and material balances as well as mass transport and other physicvs phenomina. It took me a while to figure out what you were getting at while wondering is one could isolate thye vacuum to zones. . Zoning is easy to comprehend moreso than you think :-). you are a good person to explain things to people.a 9 x 4 CNC could be quitye rigid compared to 8 x 4. If one doesn't need 4 ' wide they could save a lot with even better rigidity! I may have a custom phantom made. You're very creduble. I'm a scientist, not an engineer but much the same

@Statedwoods 5 ай бұрын

Thanks for the kind words. Appreciate that

@j77364 8 ай бұрын

Hi Nick, would you be able to share the specs of your vacuum? Power, CFM, vacuum pressure etc. I am struggling to find the best solution for my 4x8 table.

@Statedwoods 6 ай бұрын

Just depends on the unit. Lots of single phase and 3 phase motors out there. Cfm can vary a lot and pressure has a lot to do with your table and how well sealed you have it as well as factors like elevation

@timsewald8270 8 ай бұрын

I have a question about pump size. My vacuum table is HDPE 41"x30" or 10.25 sq ft. I will be using ultra light fiberboard for the spoil board. What pump would you recommend? Or, can you give me pump specs I should look for? I have single phase 220 on a 30 amp breaker. Appreciate your reply.

@Statedwoods 8 ай бұрын

I would get a 2.2 kw pump from Phantom CNC. Ton of power for only $750.

@p8ntblr1 5 ай бұрын

Is there anyway to add dog holes to your spoilboard and still use the vac table? Thanks for the video

@Statedwoods 5 ай бұрын

You could but understand that those areas would have less air flow to them and could allow air to escape depending on where the cut throughs are after parts are cut.

@Statedwoods 5 ай бұрын

5 if you count a plasma CNC i have now too

@NolanBuilt 10 ай бұрын

Great video Nick! Everything was thoroughly explained, clear and concise! 👌🏾

@Statedwoods 10 ай бұрын

Thanks Nolan. I appreciate that. I tried hard.

@thisoldman7142 3 ай бұрын

Great video. Suggestion: fill the unused spoil board with scrap as directed in this video. Add a gasket under the project piece perimeter using door/window self adhesive weather stripping. It comes in 1/4” wide by 1/8” thick rolls and only cost a few bucks.

@Statedwoods 3 ай бұрын

Always great ideas.

@seanmichael5751 2 ай бұрын

in my experience, while this works relatively well in a pinch, you really have to play a puzzle game trying to find the scraps that fit together to cover the rest of the table. sometimes it defeats the idea that you're saving time and hassle by using a vac table.

@ajitwadsal6161 3 ай бұрын

WHICH ONE IS BETTER A VACCUME BED OR CLAMP SYSYTEM BED ?

@Statedwoods 3 ай бұрын

Depends on your jobs. Sheet goods then vacuum. If small parts and small material then clamps work well. Depends on your situation

@MattVoda 8 ай бұрын

Any experience with aluminum sheet? The lower friction makes me worried

@MattVoda 8 ай бұрын

Oops just got the part about All Star gasket. Seems like that foam tackiness would help with aluminum. Second question - is your vacuum pump inside your shop? Seems very quiet with the vac table running

@Statedwoods 7 ай бұрын

The tile gasket makes a huge difference. It will greatly help with aluminum. My pumps are outside but you dont have to do that. They can go under your machine if needed.