Siemens compact 7SJ8081 relay Navigation, parameter settings,relay testing, alarm/ fault/led reset

Siemens 7SJ80 Siprotec compact relay Navigation, Basic parameter settings(CT-PT ratio setting, Overcurrent & Earth fault setting/relay basic configuration), basic relay testing, View Fault record its time, alarm/ fault/led reset, communication with digsi, CT ratio change, manually change setting/parameter, manually check BI, BO & LED, Etc.
Note: For almost all Siprotec compact series relay, all shared process will be same.
#Siemens #relay #relay testing #relay configuration #7SJ #CT ratio change #relay reset #relay communication # Relay Navigation #Siprotec compact

[@RahulKumar-sw2hk]

Thank

[@subhrajitdas1990]

Thanks sir for relay training video..we expect more relay videos from u..plz

[@hiteshdharaviya8129]

I am very excited for new video.

[@abhisektestingakshar1014]

It's very helpful for..me..ty..bhai .🥰🥰

[@dnyanotech1404]

Very nice information

[@KingBD328]

Great job

[@aexm6527]

I have to set the first earth chain threshold to 2A with TO 100/1 but the minimum value is 0.05 of the nominal value. come what should I do?

[@badshahibrahim8475]

Thanks for it

[@badshahibrahim8475]

Bro dayafter before I have tested this model relay but it couldn’t trip why?

[@badshahibrahim8475]

It’s should trip before configurations or not?

[@pratikbhatt95]

It's BO-LED may not configured.

[@badshahibrahim8475]

@@pratikbhatt95 okay 👍🏻

[@user-gm4ph9fj7c]

Sir, how to copy relay settings to spare relay through Digsi software

[@pratikbhatt95]

I got your mail, i replied over there...👍

[@chandraanand4102]

7sk8012 model

[@Ya_Allah_madad-786]

Sir, is input DC IN 1 and 2 is 24 volt? Best regards

[@pratikbhatt95]

No, this model is for 60-250V DC & 115-230V AC. For 24V you will have to choose different MFLB number

[@Ya_Allah_madad-786]

@@pratikbhatt95 Thanks a lot

[@ruinica2118]

What digsi version are you using? Everytime i tried to connect it to digsi v4.92 it says cannot connecy

[@pratikbhatt95]

You should have device drivers for same model & same or higher P-set version, which you can free download from siemens website.

[@user-kb9qx6hx4z]

is it possible to change the IDMT curve in Device configuration without DIGSI??

[@pratikbhatt95]

You can't change in device config. without digsi. But if you already enabled IDMT in device config. then you can manually change curve in settings.

[@user-kb9qx6hx4z]

@@pratikbhatt95 shall we do in trial version of DIGSI

[@ahmadzubik7412]

how i can download new virgin 4.79 to digsi 4 because the devise dont conaction ??

[@pratikbhatt95]

If you are having no driver installed then you have to download from siemens website. It's available free. It will just ask you to register then you will able to download.👍

[@user-yo9qz7cv2g]

Sir,I have a problem. how can i leave monitor mode? Which is ''SIEMENS intern'' password?

[@pratikbhatt95]

First try to initialise proper programme, or default programme with basic settings. If not working then contact me on [e-mail]

[@singhbains6903]

Sir how to communicate this relay via ethernet port

[@pratikbhatt95]

There is no ethernet port available in these type of compact series, you can communicate with printer cable only...

[@rezaulkarim1369]

Sir, can you provide software to me.

[@pratikbhatt95]

Software is available free on internet but you will have to get the key from somewhere...