Simplified Armature Diagrams Part 1 (2)

Hi guys! I got another video about simplified versions of an armature diagram.
We all got that one experience when we were searching for diagrams and at first sight
we lose our motivation right? Well worry no more, like you, I love simple things
and this video is for you.
By the way, the diagrams used here are all made up, they serve as an example only.
I'll be releasing diagrams of power tools that we have repaired in the future so stay tuned.
Plus the wire used is not a wire, its actually a cotton string.
Also I forgot the model of the armature used or what kind of power tool it belong and the commutator and armature are already broken, its just for study.
Anyway, sometime in the future I will show you how to figure out the diagram of armatures.
Thanks again guys ;)
Music used:
Old Bossa
Old Bossa by Twin Musicom is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Artist: www.twinmusicom.org/
Okey Dokey Smokey
Okey Dokey Smokey by Audionautix is licensed under a Creative Commons Attribution license (creativecommons.org/licenses/...)
Artist: audionautix.com/

[@knottreel]

Thank you. I needed to see this drawn out along with the demos.

[@hasanrazaqadri9526]

Very very very very very very very very very very very very very very very very very very very very very good explanation thankyou

[@pyt22fr11]

Nice explanations, great ! However, do you not consider any rotational (i.e. angular) offset between segment and slot ? How do we adjust them ? Thanks !

[@belmiromunck6683]

Muito bem explicado você trabalha muito bem valeu amigo Tmj!

[@zondepa5537]

Great video! Many thanks! I have one question. I have right now one armature with the same slots as you have shown in the video. My question is: the wire that was used in my armature is very thin and i do have one which is thicker. Can i use it too? Like calculating the weight of the old and convert it to the new thicker one? Would it be the same?

[@khalidhadi8434]

Merci beaucoup pour les informations

[@angelicafernandez8772]

Very nice explaination, thanks for the video..

[@user-ob2un5pd7t]

Thank you

[@JakeMarvinVillegas]

You're welcome 😁

[@OmidShakeri]

good job! thanks...

[@agastinrino4034]

Angle grinder Bosch Gws7-115 armature winding data

[@Mad_Scientist2052]

How do you determine how many wraps per coil?

[@ucandoit5398]

Fantastic

[@surathgaladeniya5988]

thanks a lot❤️❤️👌

[@sammunyagwa2721]

Bravo man

[@rezafly2972]

hi sir please How To winding The Angle Grinder armature Of 13 Slots And 32 segments ? thank you

[@alejo8053]

Beatiful

[@zadvindersingh4234]

👍👍👍👍👍👍

[@MujibRewinding]

Good explanation, I tried but got reverse direction 😭.

[@JakeMarvinVillegas]

You can reverse the connections of the carbon brush sir

[@ferreirodequintal8440]

show 👍👏👏👏👏

[@mohamedwafir1577]

Good idea

[@JakeMarvinVillegas]

Thanks Alex

[@siroedhiekreasi]

Very nice knowledge, let me download it please. Thank you

[@JakeMarvinVillegas]

Sure no problem sir and thank you

[@user-wq4km6rk9f]

جيد جداً بداية رائعة و واضحة

[@jimmark2010]

Well done very helpful , thank you

[@JakeMarvinVillegas]

Thanks jimmark2010 😇

[@jimmark2010]

Have a look on youtube (technical babajan) I like his videos new winding method your one is good too

[@JakeMarvinVillegas]

Sure I'll watch his videos jimmark2010 thanks for telling me 😇

[@hasanrazaqadri9526]

My question is my armature had 16 turns in one slot so I have to wind 8-8 turn or 16 and 16 in one slot??

[@JakeMarvinVillegas]

Hallo there Hasan, it depends on your commutator segments. If its 32 and the number of turns u counted in one slot is 16 including the windings of the other side then it should be 4 turns because you have to do it twice. 4+4 from the other side, and 4+4 from the other also total 16. But if its a 16 segments commutator then 8 turns and only one windings per side.

[@JakeMarvinVillegas]

Sorry bout the late reply i got really busy

[@hasanrazaqadri9526]

@@JakeMarvinVillegas it's ok I have completed my winding property bcoz of you thanx

[@qaisarawan93]

@2:20 you choose the slot next to the commutator slot in front of the slot in armature but you rotated the wore and then winded at some other place place. @2:14 you first put the cable in slot in front of the commutator slot. Then wrapped it around.. What's the trick In it? I m stuck here

[@JakeMarvinVillegas]

It is to make the wires neat and arrange, if i would just put it right where it should be it would block the way for the other connections sir

[@MinSziHo]

how to safely remove insulation from wire touching commutator ?

[@JakeMarvinVillegas]

To easy remove it you need to make the epoxy brittle by burning the part where the wire and commutator touches.

[@ferreirodequintal8440]

like 😎

[@ashokballatagi1318]

Great teaching. Thanks. I have following doubt. Pl.clarify. Pre winding coils. With 3 outlet terminals. Commutatur. Clnnectionr 1. 2 .3. 1st coil 3. 4. 5. 2nd 5. 6. 7. 3rd ........ 21. 22. 23. 11th coil 24. Slot. Left over. ???? We need 11 coil. But 12 slot Armature we can only put 6 coils in each slots. Can we put more than one coil in each slot ???? Pl. Clarify. Thanks

[@JakeMarvinVillegas]

Hello sir thanks for watching. No sir the first outlet is for the half of the first coil, while the second and third outlet is for the second coil. When we loop around back to the 24 and 1 outlet it will complete the first half of the first coil. 1. Half of first coil 2.3. 2nd coil 4.5. 3rd coil 6.7. 4th coil 8.9. 5th 10.11. 6th 12.13. 7th 14.15. 8th 16.17. 9th 18.19. 10th 20.21. 11th 22.23. 12th 24. Another half of the first coil That completes the windings

[@ashokballatagi1318]

Need clarification.

[@ashokballatagi1318]

Thanks

[@Adelekejr]

Is there somewhere i can contact you? I need help on a amature

[@JakeMarvinVillegas]

Good day sir, you can try and contact me through email [e-mail]

[@Adelekejr]

@@JakeMarvinVillegas sent you a mail

[@rezaamini4791]

Sir i have a very painful question from all videos;why some guys start winding from some segments before the segment on top of slot? please help

[@badshah_pro]

It is painful for real because I have the same issue and no one answered till now. For all the videos I asked

[@andreacarli5910]

Hi. What is the difference between your rewinding using a SINGLE wire and the rewinding using TWO specular wires as shown in this video kzbin.info/www/bejne/nXaunWWjppJ3Z9E ?

[@qaisarawan93]

Exactly my question. That man is from my country but he doesn't mentions why two. I believe it's easy to use two. He has many more videos so considering his experience I would say that his method would work great

[@guddubhai6877]

Sir vacuum cleaner armecher riwaindig 22 slod 22 segments dayagram please

[@goojoe1974]

Still not understand

[@JakeMarvinVillegas]

Im sorry sir i will try making a new vid in the future

[@eugenioflores5625]

from where are you Jake

[@JakeMarvinVillegas]

Im from leyte sir

[@katizoom6161]

Ac or Dc??

[@JakeMarvinVillegas]

this would do both sir ac or dc

[@rosangelapires230]

Se

[@davelar3868]

Need to be a fast reader hard to keep up

[@subhashjee3597]

Bhai koi hindi me samjha do yar

[@becongcabahug7016]

you cannot be a teacher on showman.

[@JakeMarvinVillegas]

Good day sir could you give me ideas on how to improve my videos 😞

[@niteshvishwakarma5655]

Not helpfull a little bit