singer fashion maker sewing mashin full service part 3

[@kadrirafiqueahmed4307]

Sir, aap ka bahut bahut shukriya point to point sikaneka.jazakallah khair.

[@LaxmibenVagh]

Datisetgbatavo

[@mimirimivlogs]

I have same machine ..... zigzag mode pe bhi sewing straight a raha hai....... zigzag nhi ho raha hai..... plz give me solution...

[@Anon20139]

Mera bhi yahi problem hai. Kya aapko solution mila?

[@VyomMengar]

Well I have same machine , but I want to know how to adjust stichies in center with zigzag pattern , when ever I'm keeping zigzag setting to max ,the needel goes to extreme lrft to center Right instead it should go rxtreme left and right, hope your further videos will hrlp me out with this.

[@navathag4028]

Same problem ...if you found any solution please tell me

[@VyomMengar]

@@navathag4028 i found a solution to it. It would be better if i make a video out of it. I don't know how to describe it in writing. But here it goes ill try best to explain in words I wonder if anyone would gtt me, well there are two micro adjestments to keen needle at center 1. At the back of the machine interior michanism there is a screw holding a thin rod which is connected to needle swings - unscred and adjest needle at center by your hand and hold that position and then scred the nut. Which will basically adjest it to center. 2 here comes micro adjestmenta in mm if it is still off the center, not perfectly center. For this you need a thick string to hold/adjest/pull the needle rod (not the needle but where you attach needle). So loop the string around the rod and you have to pull it towards(there is a module to attach pattern disk / todards where you attach different pattern disc). And there is a leaver which is attached to adjestments where you want your needle to be (center right or left) so there are two screw over there you need to focus on the scred which is near the rod (the needle positing leacer - center right and left) it would be a bit hard to unscred that because while un screwing it the stich length adjestment will get in the way. (What you need to unscrew is the screw which is attached to rod with a L shaped leaver/ is forming right angle and you will be able to unscrew it sidways not directly. (Do this process when the stich setting is set on "straight" not on zigzags) Step1. So unscrew that screw, a little then pull the string till you find the needle center you are loocking for. (Keep the string hold in that position throught step 2 - needle at the center at the merking plate) Step2. Then you have to adjeat the L / inversely L shaped leaver such as it is pointing at the center reading / marker on acrellick / plastic. While holding the string keeping needle at center positioh and then screw that L shaped leaver / or mirror imaged L shaped leaver back on. You can release the string bcz now the needle adjestments are done an your needle will be on center. When you are using zigzags your stiches will be equidistant from the center needle position. Let me know if you got it properly. Ill try to make it simple to understand it if possible.

[@navathag4028]

@@VyomMengar thank you for your reply...i saw your message just now ..after trying so many things I gave up and 2 days back i went to repair shop..he solved the issue by replacing center position leaver.. now it is working good..

[@mannatdeepkaur8472]

@@VyomMengar please make a video on this problem.so that we easily understand

[@Anon20139]

​@@VyomMengarI was hoping to find your video for this. Do you have a suggestion for my problem? The needle is hitting the back of the hole in the plate. I need to find a way to align to centre by moving the bar to the front.

[@AjayAjay-qv5xq]

Sir daat uper niche ki setting batao kharab Ho gayee h

[@AjayAjay-qv5xq]

Daat ki rod ki setting batao please bohat pareshan hu

[@aliparwez1797]

Binod bhai video banane ka bahut bahut sukriya Assam me karfu tha iss liye net bhi band tha aaj me ne aap ka video dekha

[@debasishraychaudhuri4679]

Please show singer sewing machine multipurpose handbase zigzag repair . Your instruction and process is very good

[@umarajendra1316]

Sir, I am using this type of singer maching. The problem is zigzag width is not coming completely. If I adjust full width the needle will break. Please show how to repair the width size. Please waiting for your early reply in next video.

[@balacv02]

Bahut Accra. Mera hook jo hai dahga uta Letha hai, Lekin age jake chord tha nahi he.

[@user-ju1xm6wk7i]

Super Bhai good Dhanyvad

[@sureshyammi4154]

pico stitch is getting gap what should do for that?

[@shashikalalazarus2977]

Apne ek video me bataya ki spring apne uparse lagaya Asia spring Lebanese picco zikzak ho Santa hai kya pls bataye.🙏

[@ipk5418]

Ser ak video banae is machine ke tap ki problem bare bataye ,thank you !app bahut achhe say sab batate hai.

[@vision8776]

I did everything like u showed but in the end the wheel became very tight . Just cant move it freely.pl do help . Had to redo the whole. Tried to get a mechanic but he is down with covid. Need my machine as,soon as,.possible pl do reply

[@Anon20139]

Kapda rakhne se right mein straight stitch theek aa raha hai par center aur left setting mein ek bhi stitch nahi lag raha hai. Zigzag mein pura left mein dhaaga chod raha hai. Bina kapde check karne se hook dhaga pakad raha hai. Kya carrier mein problem ho sakta hai? Carrier ko kaise adjust karien?

[@SaurabhSingh-gp8os]

Simple silai ke liye singer fashion maker classical mein kaun se chip ka number lagta hai kaise lagta hai iska video banaa dijiye

[@shashikalalazarus2977]

Spring machine hai ke nahi kaise malum hoga. Apke 2 parts to mile lekin 1la part nahi mila pls 1st part wapas dale🙏.

[@bantibhagawati1891]

Sir mera ek singer multipurpose zig Zag mechine hai 2001 year ka. Ob usme needle fix ho goyee ha pico orzig Zag mohi ata hai .please iske bare me eek video bonakor dijiye .bohut madat hogi

[@Anon20139]

Is machine ka face aur top ka fitting ka video banayiye.

[@zenabezzy2530]

Please sir full video banaye k 298 singer machine ko use kese krte hai

[@homemangalam]

Sir meri machine me embroidery designs wala part nahi chal raha hai... only one side (left) stitching is working.... how to fix this problem by myself.... please explain/suggest me....

[@indraagarwal2213]

MERI machine piko Nahi ho Ravi hai I have good macanic in Amroha

[@shashikalalazarus2977]

Sir meri same mashin hai lekin abhi zikzak our pikko nahi hota hai pls app eske bareme bataye to acha hoga.

[@devinajain3394]

Sir, I have the same singer fashion maker. Stitching nahi ho rahi h machine se. Bobbin thread coming up but sewing ni ho rahi h. Pls explain why

[@incredibledunya8154]

Sir interlock ki disc khulti nahi hi doosri disc change kiss Torah karate please reply

[@imrankhilji7730]

Good job sir

[@shivshankarnetam2175]

Zig Zag timing adjustment techniques Needle going out of the hole please guide me Sir .

[@mukeshkumar93111]

Sir mere machine me while nhi ghum raha hai please help

[@dilipchnadane972]

Timing hillnese dhaga cut hota play. Reply

[@ipk5418]

Sir iska flower disc lagana sikhaye next video may so that zig zag thik kiya ja sake sir please Maine new flower disk manga liya hai please I request you to make video thank you so much itna achha sikhane key liye

[@bkbhowmick1441]

Zig Zag timing adjustment techniques. Needle Going out of the hole.

[@umeshyadav-hq4dd]

Sriman ji mere pass singer ka maltiparpose model hai lekin machine puri jam hai Koi makanic banana KO taiyar nahI hai Kay karu margdarshan kijiye pls nivedan hai

[@sumanjangir1266]

Mere pass b yhi machine h baiya kse khole career rodh tutgi aage s

[@prakashtrivedi6747]

अहमदाबाद सिंगर फैशन मेकर सर्विस सेंटर का एड्रेस बताना

[@syambagaming9718]

Niche wala part to mujhe samaj aagaya lekin upar wala part assembly nahi kar paarahe hai kuch solution kijiye sir.

[@real_gaming_8900]

Veer g kadhai kese krte h vo bhi bta do plzzz

[@Rajesh_0013]

Singer multipurpose old model fashion maker me needle kon shi lagti he raund wali ya khache wali lagti 100/16. Please rpl.....

[@vinodbhatt2000]

Half shuttle cut niddle full shuttle round niddle

[@hisharabalakrishnan1556]

I have same machine . I dont know how to repair needle hitting on needle plate

[@Anon20139]

Hitting which side?

[@arshpreet_kaur397]

Sar mery mashin singar imrodry baly mashin he eska spearpat plastic kahe eske guj me problem he to ham Kia kre

[@abdullahabraz8260]

Design khrab ho to kese shi kare.please tell me.

[@dilipchnadane972]

Thanks sir pure samaj me aaya thanks uske spar part milega

[@muralikumar945]

Please explain the details of Fashion Maker Rotomatic 974

[@baluahire7250]

सिंगर मशीन ची सेटिंग गोल गोल टीप पाहिजेच काय करावं लागेल.सर प्लिज सांगा

[@salmasayyed2791]

Jis purje se sui niche upper hoti hai uska video bataye

[@asadd4563]

Sir mera same machine h.. Jiske chanp ke niche ka zigzag dant niche ho gya h( Niddle ke niche) ... Jisse kpra aage ni bdhta h silai krte time... Plz help

[@ritapal4324]

Meri machine daga todti or silai chod rahi h plezz sar isko sahi karne ka video banay

[@firdousrazakhan6344]

Y kis city sy hy aap

[@styawanstyawan376]

Bobin bàrneka assèmbly tuta gaya naya milega kya

[@jeevantaraptla7633]

Shuttle kaise parts kaise batao kaise fit kiya

[@ipk5418]

Sir apne machine ki timing ache say nahi bati so please singer fashion maker sewing ki only timing dubara bataye .apne hame puri jankari di thanks kafi kuchh sikha

[@ipk5418]

Sir is machine ki needle jab niche shuttle may jati hai to chand ko right side per hona chahiye ,lekin ye chand may left side per noch hai jaha per gear ka nut jate hai to aysa video banao ki needle ka chaker jo ander Jata hai us samay baher aye aur jab baher aye us samay ander jaye please give solution so I can set timing is machine ki ke saku thanks

[@jagbeer2jack]

Sir same machine.. niche wala thread tod rahi bar bar

[@laxmiprasanna4144]

Sir namasthe. Hamara fashion maker machine hi straight stich achha araha lekin zigzag stich bahoth skip horaha sir solution baths de sir Krupa karke

[@madhumitaroy995]

আমার মেশিন singer fasinger makear আমার মেশিন নিচে সুতা জমা জমা হয় কি করব

[@Streetfoodtadka_2929]

Sir is machine ka table pair fitting kaise karte hai pls ek video banaye maine machine liye huye 6 mahina ho gaya abhi taki nahi chala payi pls sir table pair fitting ka ek video banayiye

[@kkswain4268]

Sir, Mera Ek problem ko video jariye se solve kijiye., Ye fashion maker machine main needle upar se hi left-right Sifting hoke niche utarna tha. Lekin mera machine main ye problem he ki needle bar niche utarte hue samaye nichemain hi Sifting horaha hai . Pls Sir Explain .,

[@ipk5418]

Sir meri machine tap barebare chhor rahi hai ye problem key liye needle bhi niche ke date bhi uper kiye but thik nahi Hua

[@arshpreet_kaur397]

Mashin nover 988 he please sar btae

[@mdshoaibshoaib9970]

Hamari machine mein kapda aage nahin ja raha hai atak raha hai aur dhaaga bhi nahin a raha hai kya Karen

[@pkrprao5947]

Vinod jee,. Zigzag setting out hojanese kiase setting kiyajata hai. Pl apne video me batayen.

[@vinodbhatt2000]

Ok

[@ipk5418]

Sir iska timing normal state silai ke liye set kerna bataye

[@aliparwez1797]

Binod bhai good morning part 4 video kab banayenge

[@sumanjangir1266]

Esko aap jaante ho to mujhe eske no dedo machine m bhot dikkt h

[@kaneezfathima2020]

Sir ye machine normal mode pe hai pico kaise kare

[@praveenkaveeshwar]

Part 4 bhi banaye

[@zahuriqbal4286]

Sir designing disc rotation m nhi hai uska inside ki garari tut gai kasa remove karu

[@pratibhasharma3796]

Zig zag ki Jagah straight stitching aa Rahi🎉 hai

[@santoshbudhale907]

Yeh machine mai pico larne ka setting lagaya to niddle baju vale chand plate mai takara jati hai pls niddle bar setting batao

[@vinodbhatt2000]

Jyada liver ko na ghumaye

[@gazalaalam2923]

Sar mere paas bhi Yhi machine hai Esme bobin ka dhaga Bohot tut rha hai toh kya kre Kuch btaye

[@kaneezfathima2020]

Mera bhi yehi problem hai pls reply sir

[@santoshbudhale907]

Fashion maker ki niddle bar chand plate ke bahr ja raha hai so niddle set kaise kare

[@vinodbhatt2000]

Ok

[@muskanmansuri6339]

Good sir

[@SunitaSharma-hv6dy]

sir plz kripy kr bta dijiye meri machine agge ni badh rai ek jgha hi atak gai h

[@fulchandra7439]

Multiparpas link jam kaise छाएं

[@Rxthetics]

Mere pas bhi yahi silai machin h

[@anitaagarwal31]

मैरे पास है मशीन मेरेबहुत टाईट चल रहा है कया करे

[@mustafahafsa9783]

Mjhe parts need h sir

[@antonmenezes4948]

Dhaga tutneke bareme dikhav

[@shallykaur6991]

चक्का चल रहा है गज नहीं चलता कृपया क्या करें जाम हो गई है क्या फैशन मेकर मशीन का पूछना था

[@vinodbhatt2000]

Puri machine me oil dale

[@vinodbhatt2000]

kzbin.info/www/bejne/fHe7YmtugdOjgas

[@AnilPatel-tv2vw]

पीकु करते समय सूई एक साइड में फुट पर टकराती है

[@owaisiqbalvlogs468]

Iska Gear kahan milega

[@vinodbhatt2000]

Nahi milega

[@anuradhabatish1342]

Vinod ji aap kahan se hain agar machine aapse hi thik karvani ho tou kaise contact kare.

[@rosariodias7869]

Dhaka upar nahi ata to kaiser set kare

[@sarojpatil3031]

सर माझी फॅशन मेकर मशिन आहे पण ती साधी शिलाई करते पण पीको करत नाही तर कशी दुरुस्त करायची ते सांगा

[@anjanghosh6840]

Sir hamara machine ka middle teaching Nahin pakad raha hai kya karu

[@udaysinhvaghela2458]

शीधीसीलाय होतीहै ऐमोडी नयहोती सेटीग बताऐ सुईङुङजातीहै सेङीग बताऐ

[@mehrajkhan9303]

Meri silai masin ka date vala look tut gaya hai

[@mamtamittal2799]

Mere pass bhi h aise mashin awaj bhut krne lagi h kya kru ap ka no dege

[@mansoorbasha9572]

Hello sir zigzag ka video dalo na

[@SonyMonica]

Fabric is not moving sir

[@santoshbudhale907]

Sir bag closer ki timing ser karna ka video banao

[@ronappereira8446]

Stitches Ka demo batya

[@ritarkolha6847]

Mere pas BHI hai stitch me gap as rah ahai

[@gazalaalam2923]

Sar eske foot Kitne ate hai

[@richagupta333]

Sir Meri machine ka gajj Bahar as raha hai

[@ritasutradhar1845]

Singer rotomatic 8 repair

[@mohsinsahito5449]

Ache

[@paltuhalder9675]

Umbrella machine mein naya gana lagane ke liye karna padta hai

[@umeshtupe3051]

Thanks sir.

[@anitaagarwal31]

आवज कर रही हैं कैसै ठीक हो

[@santoshbudhale907]

Sir we r waiting for your video pls upload as fast as

[@vinodbhatt2000]

Topic?

[@santoshbudhale907]

@@vinodbhatt2000 fashion maker niddle bar setting today u upload this video

[@divyanadhanxavier3873]

Part 4

[@ranjeetsingh-cq6hw]

Thank you sir

[@veenavidhatveena5452]

Sir Usha empress no 721213979 ka full service kaise kare bataye