🔸 Why doesn't my sewing machine sew? | Crab adjustment

[@ionolaru7441]

magistral !

[@javiery70]

@@ionolaru7441 thanks 🙏

[@Tk_jh]

I was absolutely amazed by the thoroughness of this video. It solved my problem with my machine and I learned how to calibrate the needle and hook properly. Thank you so so much-I’m am very grateful!!

[@javiery70]

@@Tk_jh Thank you very much, I'm glad it was helpful. I encourage you to support my channel with a subscription (it's free) and to watch more videos. Thank you very much 🙏

[@javiery70]

@@Tk_jh thanks 🙏👍👌

[@l1ncs]

this is what an instruction video should be like .. thank you .. nobody has covered this with this clarity

[@javiery70]

Thank you very much and thank you for commenting, not everyone is grateful...

[@Sapnakori9]

Yes this is good and informative However with 5400 singer series the bottom part is not accessible easily. Any ideas for it?

[@javiery70]

@ on the bottom cover there should be removal screws, it may be hidden under the support brackets...

[@old_blues2397]

Oh! Oh! Oh! Oh! What a video! I needed this! Will try it out! Thanks!

[@javiery70]

thank you 👌

[@k_moov3]

This was it for me! Just extended the needle a tiny bit. Thank you 🙏

[@javiery70]

👍👌

[@nazjankurt2717]

So I can't thank you enough, even singer's original videos don't say what you say.. My problem was that the needle was not in the right place and I took it out of the bobbin part(?) and put it back in. Thank you very much, I'm a new subscriber!

[@javiery70]

Thank you very much, I'm glad the video was helpful to you.👍

[@javiery70]

👍👌

[@odiaparibara]

After watching this video my problem was solved. Thank you so much 😊

[@javiery70]

👌👍

[@elwoodbluesmorris2120]

Thank you so much, I just used all this advice to fix my machine, wonderful well explained video.

[@javiery70]

@@elwoodbluesmorris2120 thank You🙏👍

[@elwoodbluesmorris2120]

@@javiery70 Hi, Do you have any idea why the timing would keep going out of time? Since fixing it earlier, I had to do it again, and it has now again gone out and is not picking up stiches? Could there be something more serious wrong with the machine?

[@javiery70]

Check that the adjustment screws are properly tightened and that the gears and shafts are clean and lubricated.

[@elwoodbluesmorris2120]

@@javiery70 Thanks for the reply, I might try getting new Allen screws.

[@XVRickXV]

Fantastic video! Got me back on track!

[@javiery70]

@@XVRickXV thanks 🙏subscribe

[@creativeshabu1147]

I have singer machine. Your video helps me to fix the problem. Thanks a lot.

[@javiery70]

@@creativeshabu1147 Perfect. 👌 Thanks for commenting.🙏

[@arunagujar7739]

Thanks for the perfect explanation and solution! Thanks from India!

[@javiery70]

👌👍

[@Abimbola.Abioye]

This has helped me twice now. Thank you so much for the detailed video!

[@javiery70]

👍🙏

[@alpanosap]

Wow what a nice, useful and practical yet short video THANK YOU SO MUCH.

[@javiery70]

@@alpanosap 👌👍

[@shamseltaf8618]

I have the same issue with my Singer machin , since a year now i fix it from your video it has help me alot thank you for such great video. ❤

[@javiery70]

@@shamseltaf8618 I'm glad it was helpful, thanks for commenting.👍

[@ich2990]

Thanks so much for the explanation!

[@javiery70]

👍👌

[@Cavolfipriecapperi]

Thank you so much, you couldn’t be clearer!❤

[@javiery70]

@@Cavolfipriecapperi thanks 🙏

[@mirag2k]

💐alignment step and fix you suggested works in general. It helped me to fix Usha Janome machine at home. Thanks a ton,💐

[@javiery70]

Thank you !!

[@grahamwoodley8889]

Great video, I have a Singer Symphonie , seems identical in every way to the Serenade , timing was not correct, easy to fix following this video. Thank you.

[@javiery70]

👌👍

[@MaryTau-iq6gb]

Thanks a lot my machine is sewing crab and I don't know what to do I'll start using your teachings maybe I can make money God bless you

[@javiery70]

@@MaryTau-iq6gb 👌

[@maanlicht96]

Lifesaving video!!! Was able to fix my machine due to the detailed description and video!!

[@javiery70]

Thanks

[@LorrianneSipana]

This was very a helpful tutorial video that helped me rectify my sewing machine issue. Now I'd just like to know why this happens in the first place.

[@javiery70]

This happens because the mechanical parts wear out with use or simply because the adjustment screws are not tightened sufficiently.

[@LorrianneSipana]

​@@javiery70thank u very much for your response.

[@diatonicdoug6525]

Because on wide ZZ the hook timing changes the needle to hook timing because of dancing needle

[@StingRayPartsWashers]

trying to sew too thick of material, breaking needles, crashing the machine with thread jams in the bobbin area can all cause the timing to slip

[@fluchterschoen]

Something important that you don't actually say in this video, is that the position of the needle relative to the hook/crab should be adjusted and set with the needle bar in its furthest right position. The video correctly says to put the machine to the widest zig-zag stitch, but the narration forgets to tell you why you need to do this and that you only adjust with the needle at the farthest right position.

[@javiery70]

Thanks for the comment. You can see in the video that the zig zag mode must be at maximum. I will add that information to make it more evident. thank you so much.

[@JupiterLight28]

This is a great detailed video and very helpful. My timing looks perfect but I'm still having issues. The measurement is also at 15 mm as it should be 😮‍💨😭

[@AkosuaBorgaCuisine]

Great Very helpful

[@javiery70]

@@AkosuaBorgaCuisine 👍👌

[@BTYBYG]

Amazing video but It seems for me even with things loosened the crab does not rotate freely. Its very stiff. I Uploaded 2 of my own videos just now. I bought machine used but it looks new. Really hoping to get it working any tips would be appreciated!

[@javiery70]

If it is rigid you can try to lubricate the axles and gears.

[@BTYBYG]

@javiery70 OK thank you!

[@ShivAadesh]

​@@BTYBYG Hello, how's your machine working now?? 😇 Hope your problem is solved and it is doing it's job well.

[@BTYBYG]

@@ShivAadesh I unfortunately didn't get it working. I gave it to a friend. I still enjoyed the video :)

[@obontitoma8491]

That ones i was looking for a long time

[@javiery70]

👍👌

[@adamgloria9263]

Nice one mine is having this exact issue thank you let me now work on my machine

[@javiery70]

👌👍

[@nurbk5184]

Faydalı bilgiler teşekkürler... bende singer xl 550 nakış var düz dikiş yapmıyor yerinde sayıyor dişli si kalkmıyor... nakista ise altına paso yapıyor tansiyonunu yükseltiyorum bir işe yaramıyor. Ne yapa bilirim

[@javiery70]

Türkçe tercümesini pek anlamıyorum. Yapabileceğiniz şey alt kapağı çıkarmak, elle çevirmek ve sorunun nedenini görmek, herhangi bir dişlinin dönüp dönmediğine bakmak...

[@elmuyguapo779]

Thanks for this video.

[@javiery70]

@@elmuyguapo779 👌👍

[@ShivAadesh]

Hello There, Firstly let me APPRECIATE your efforts, very well narrated and well presented and beautiful video. I liked the video and subscribed your channel because I really liked the way you presented the topic at hand. I encourage you to make more and more such videos and wish you good luck and growth in your endeavours. 😇 Now, for my concern, My machine's crab hook is rubbing onto the needle, would you kindly suggest how to fix this please?? Its position is okay as per this video. Thank you.

[@javiery70]

Thank you very much for rating my video positively, positive comments are appreciated. If the needle rubs against the crab and the position is correct, it would be necessary to check if the needle is correct for that machine. It would be necessary to check that the crab is correctly adjusted in its housing. With the correct synchronization of needle and crab there should be no friction. It is also important to check the height of the needle.

[@Jyothi-wf2tf]

Thank you so much

[@javiery70]

@@Jyothi-wf2tf 👌

[@hartiemfarrell3485]

Thank you so much for this detailed video! However after I loosen the two Allen screws at the bottom and pray the crab with lubricant it still does not move.

[@javiery70]

Check that it is the correct screw that corresponds to the axis that moves the crab.

[@elwoodbluesmorris2120]

There are three allen screws, it's the bottom two that need to be loosened, relative to the machine being on it's side.

[@DAS0906]

Thanks you

[@javiery70]

@@DAS0906 👌👍

[@lokeswararao24]

Thank you neatly explained good presentation

[@javiery70]

@@lokeswararao24 thanks 🙏 Subscribe 👌

[@FreddyMakaniso]

Thank you very much. It did.work

[@javiery70]

@@FreddyMakaniso 😘👌

[@FreddyMakaniso]

@@javiery70 you did save me with this I stuck and about to give someone US35 to fix it. Then booom your videoo

[@javiery70]

@@FreddyMakaniso I'm glad I was of help👌, thank you very much for commenting.🙏

[@lizapalero7463]

Grazie avevo lo stesso problema che l'ago e granchio non sono sincronizzati. Grazie è stato un grande piacere sapere come aggiustare la macchina ❤

[@javiery70]

@@lizapalero7463 grazie 🙏per il commento, sono felice che sia stato utile 👌

[@southpark5555]

Most excellent vid.

[@javiery70]

@@southpark5555 thanks 🙏👍

[@Tresha-r9z]

Thank u so much for your advice

[@javiery70]

@@Tresha-r9z 👍

[@ΠαναγιώταΜανιάτη-λ2ξ]

I loved your video, I hope to see more of them. My Singer has a problem too. I bought a new pedal because I thought the previous one had a problem, but it doesn't move the needle at all, like the previous, do you have any idea what's the problem? The lamp works, but the needle doesn't move with the pedal, only by hand, it's clean, I did everything right.

[@javiery70]

@@ΠαναγιώταΜανιάτη-λ2ξ Your machine is failing in the electrical part, you would have to check not only the pedal but also the power switch. If the pedal and the switch are fine, you would have to check the electric motor. I'm sorry I can't help you more.

[@Sweet-ng6tw]

@@javiery70 Thank you for the answer.

[@쥴케패턴박사]

바늘을 잘보면 아래쪽에 조금 파인 부분이있습니다 .그곳을 밑 반달이 정확히 딱맞게돌아 실을 걸어채야하는 것 입니다 그 곳이 중요합니다

[@javiery70]

👍

[@roaelizabethmulina6098]

Thanks ❤

[@javiery70]

👍

[@JayaprakashJp-f6n]

Thank you

[@javiery70]

@@JayaprakashJp-f6n 👍👌

[@yasarathna7993]

best 🖤🖤🖤

[@javiery70]

🙏👌

[@marlisantos1770]

Minha máquina está pulando ó ponto

[@javiery70]

Por favor, tente verificar o ajuste como no vídeo.

[@Lempa4]

Bonjour bonne vidéo et la griffe comment on fait si elle est également désynchronisée merci de la réponse.

[@javiery70]

Le pied-de-biche peut également être réglé en hauteur à l'aide d'une vis. Vous devez retirer le capot inférieur.

[@Lempa4]

Merci de la réponse mais je parle de l'entraînement ou la griffe peut également se décaler.cordialement

[@javiery70]

@@Lempa4 Je suis désolé, je ne comprends pas la traduction.

[@سيلاباش]

Thank you very much, thanks to God and thanks to this wonderful video, I was able to fix my machine after I lost hope in it. I am very happy. I hope with all my heart that God guides you to the path of Islam and then to Paradise. Thank you again ❤

[@javiery70]

Thank you !!👍

[@tmj2785]

What do u use to loosen Allen screw

[@javiery70]

2 mm Allen

[@rosemarieloxton3279]

I don't know what's wrong with my machine but It seams to be an issue with the bobbin. I've videoed the problem but can't upload it! It's not producing any stitches and making a rattling noise. I've called quite a few repair shop near me but they won't look at my machine as it's a Singer heavy duty 5523 and it's about 3 yrs old. Can you give me any advise please.

[@javiery70]

My advice is to disassemble the machine by removing the bottom cover and try to see what is causing the noise, turning it by hand and see what is happening, see if the gears turn well and there is no breakage. You can lubricate the shafts and gears and try ...

[@StingRayPartsWashers]

5523 is top loading bobbin, same principals of timing apply as the machine in this video but it is harder to see the bobbin hook. Start by removing needle plate and the bobbin to have a better view. Rotate by hand so you can watch what is happening.

[@old_blues2397]

Hello javiery my crab wont even move but the wheel turns just fine and freely. What's the problem down there? Thanks

[@javiery70]

You have to remove the bottom cover and see the cause. If the movement transmission is by belt, it may be broken or loose. If it has gears, it may have its adjustment screw loose.

[@old_blues2397]

Thanks Javiery. Will try it out!

[@marlisantos1770]

Costrando quebrei a agulha encima do alfinete e agora não costura mais e não puxa a linha da carretilha

[@javiery70]

Você pode colocar uma agulha nova e verificar seu ajuste conforme mostra o vídeo, para saber se está correta ou não... e se precisa ser ajustada ou não...

[@alicegerssen]

Ive made the adjustment, only a spring came of and I dont know where it came of… help me 😅

[@javiery70]

I couldn't tell you where that spring is from without seeing the inside of the machine....and the model... try to see if it works..

[@chanduharshpreeth9644]

Same problem...pls help

[@javiery70]

I couldn't tell you where that spring is from without seeing the inside of the machine....and the model... try to see if it works..

[@alicegerssen]

It has already been made by the repairshop! 😅

[@javiery70]

@@alicegerssen 👌

[@toluadedoyin.o]

What causes the timing to be off? I keep having to get my machine fixed for this problem - like every few uses. It’s very frustrating

[@javiery70]

With use, the sewing machine can lose its adjustment, moving parts can loosen or wear out...

[@StingRayPartsWashers]

trying to sew too thick of material, breaking needles, crashing the machine with thread jams in the bobbin area can all cause the timing to slip

[@l1ncs]

​@@StingRayPartsWashers I just found that out last night sewing some denim. Mechanic cap on today to try and sort it. One would think that the devices would be made sufficiently robust to actually do what the user wants. It's ridiculous and the false marketing of devices is a real problem.

[@SandraSolido-b1i]

How to lower needle bar on my singer sewing machine model2263

[@javiery70]

@@SandraSolido-b1i look vídeo 01:23

[@ingridoverton2085]

Hi. My singer scholastic is giving only straight stitches.

[@javiery70]

I'm sorry I can't help you, I don't have a video of this problem. You would have to disassemble it and see what mechanical part prevents the needle from swinging and the cause.

[@ingridoverton2085]

@@javiery70 thank you. Will take it to a technician.

[@yusufozturk1345]

Hello, there is e-16 error code for singer 457k. How can i solve. Could you help me please ?

[@javiery70]

@yusufozturk1345 It means the thread is tangled around the bobbin. check the fit as in the video...

[@l1ncs]

after finally getting the machine disassembled and adjusting according to these excellently clear instructions, it still isn't picking up the thread 😭

[@javiery70]

It may be necessary to repeat several times until the adjustment is perfect. Also check the needle height. Check that the needle is mounted correctly.

[@Kosi_1]

What is the size of the Allen key?

[@javiery70]

2 mm Vídeo 3:19 m

[@nobohpatience9472]

Pls can you make this video for other brands like Emel . Cause that wat most use in Nigeria.

[@javiery70]

Thanks for watching the video. I'm sorry, I don't have that brand. Greetings.

[@suhainapt9305]

My machine is keep unthreading while starting the stitching process.what is the solution for this?

[@javiery70]

@@suhainapt9305 The solution is to adjust the movement of the needle and the crab, which must be perfectly synchronized. The needle must be in perfect condition and correspond to the machine.

[@LadyGGcrafts]

This would be of great help but I have a brother and getting to the belt is so difficult, I gave up 35 minutes in when I couldn't figure out how to get to my belt

[@javiery70]

Generally, by removing the covers from the bottom of the machine, you can reach the adjustment gears.

[@shahzainhaider-nm8eg]

No move chattle?

[@javiery70]

I don't understand the question.🤷‍♂️

[@francescozani8568]

Non c'è in lingua italiana grazie?

[@javiery70]

@@francescozani8568 Mi dispiace, non è ancora con l'audio italiano. È con i sottotitoli.

[@lutiDoku]

Perktheni dhe shqip

[@javiery70]

Po. Tashmë e përkthyer në shqip.

[@jennilynbatis7075]

Bakit na ok ayaw tumahi

[@javiery70]

🤷‍♂️👍

[@cafemolido5459]

Softer music, perhaps would be better.

[@javiery70]

@@cafemolido5459 Thanks for watching the video and commenting👍

[@AlirezaMohammadi-bl1vq]

❤❤❤

[@javiery70]

👍

[@Tresha-r9z]

My machine is also fix

[@javiery70]

ok

[@silviarosu5805]

👍👍👍🙏❤

[@antoninhanzlik8092]

Call a mechanic and don't put your hands in it!

[@kiwischeisse]

THANK YOU!

[@javiery70]

👍

[@ГеннадийРутковский]

Все прекрасно и понятно хотя и переводчик плохой -- браво .

[@javiery70]

👍 переводчик из Google. Попробуйте русский перевод, а не машинный перевод.