Redcat Lowriders Servo End Point Adjusting and Tuning Travel Range

[@chatobalencian1504]

About time someone explained about the endpoints good info here thanks

[@greatdane400puppys]

Keep it up Bro we can't stop we want stop Lowrider for Life Cali Life ✌️

[@Jerroldbubbataylor]

Thanks for the info always like learning

[@Baldheadnut]

Do you have a video on how to try to get the maximum steering range on the 64? I just got the Redcat 64 la Guera and it seems like the turning isn’t quite right. when I go to make a right turn, it basically goes almost straight, then finally decides to turn right slowly. Is there a way I can fix this with the transmitter? I’m legally blind and don’t have help trying to do it myself.

[@philipbahia2707]

I did not see any explanation on how to lower the ar with the point channels

[@Ghoul-805]

I just installed gatepumps and super pump setting endpoints is a lil confusing 😅 having troubles setting them

[@Carlosinator]

kzbin.info/www/bejne/jmXFdpSVfsSAeZo

[@joeycastro8591]

Hey, quick question not today I tighten up my 13 the Redcat ones which I regret buying and they rub against everything they lock up. All loose when you’re driving straight and tighten up when you go left to right what do you suggest thank you keep doing a good job. I enjoy your videos.😊

[@MonsterPartsRc]

How did you get the chassis on the ground? is it just cutting the inner fender off? what else did you have to do to get that much drop?

[@jevries]

Good Vid bro!

[@rmoreno9794]

Have this problem when I hit the raise front switch only one tire works but when I raise the two front switches bothe work.

[@NorthSideCustomRC]

Ive seen this when end points are too low under 40's IIRC we cant see how the switches are programmed but I think it has to do with this, try readjusting servo so its as middle of two end points as possible. Basically make each number as high as possible If you have 80/40 readjust to get 60/60 even better if you have a programable servo reduce travel until end points 100/100

[@DatF00J03]

What was that device you were using on the servo that wasn't installed?

[@NorthSideCustomRC]

probably the servo tester I used at beginning?

[@mrdingleschnat8436]

I accidentally broke my right rear shock when I set the endpoint to -100 on accident and it snapped 😢

[@NorthSideCustomRC]

best to test first with just the horn

[@rodri53882]

Where can I buy front stiff shocks for my redcat 64 already made???

[@psumait5157]

What up✌my steering doesn't work do you have info for that?

[@NorthSideCustomRC]

Stock steering servo is trash. I have video on best steering servo upgrade, its a must stock steering servo junk

[@terrencewestbrooks3741]

But on the 64 with the reefs servo upgrades is it different or the same process?

[@NorthSideCustomRC]

same exact process. The key for the front servo on the 64 is you have to make sure at max point both directions, up or down. The servo is not forcing while at rest. The 64 like steering is mechanically limited, but because the stuff all plastic and the servo very strong, it will push on the plastic bending it a bit, Its the exact same process, just make sure at lowest point as you put servo horn on, its NOT forcing on the servo. then do the same for the up point, but hint, a little bit of forcing on the up position helps snap hop for ups. shhh just pay attention when you hitting the stick switch yah dont leave it there.

[@danielthomas1634]

hey bro im having trouble getting my remote to work properly after doing the firmwae update......all functions working great except the toggle that raises the frontend and the round button that drops the front end are not working and i have no idea how fix that in the remote.....can you help me with that

[@NorthSideCustomRC]

go in the mixes (option in settings below end points) and make sure Mix 1, 2, 3 are off but mix 4 is on

[@Jasonkartracing]

Thank you on this one I got the 64 and just got a Monte and on the Monte the front raise only raised one side not both and I looked and looked and could not find why till I saw this and helped a lot. Keep up the good content. Oh one more thing I ordered a Castle BEC for my brushless upgrade you saved me on that one too.

[@NorthSideCustomRC]

@@Jasonkartracing glad to help out Homie and thx for the support

[@terrencewestbrooks3741]

Wish we could add videos or pics in the comments

[@NorthSideCustomRC]

where you having an issue?

[@terrencewestbrooks3741]

@@NorthSideCustomRC yea I am I have them all mounted and things but it’s only lifting the back up half way not to full lock up and the end points are at it’s highest points already 120 all sides

[@NorthSideCustomRC]

Are the shocks original size or smaller? if the servo are adjustable, you should try increasing the travel range...

[@terrencewestbrooks3741]

You have Instagram?

[@NorthSideCustomRC]

@@terrencewestbrooks3741 @TwoDubCoup

[@josetrujillo6081]

Does anyone know why my switch to raise the front don’t work

[@NorthSideCustomRC]

could be the mix settings are off. go to your mix and ig you have a Mix 4, make sure its ON, if you dont have a mix 4 (only 1 to 3) make sure they all OFF

[@josetrujillo6081]

Thanks brother big help I was lost and confused I already adjusted everything

[@bradroller6072]

What rims and tires are those?

[@NorthSideCustomRC]

These are Jevries True 13's with tripple spin off. //// These is scale to the Redcat lowriders but Jevries has True 10th scale versions about to drop. These are also V1 of the Redcat scale set, Jevries has a new version with improved white walls and also a version with all individual spoke Jevries website has a lot of scale detail stuff fir these lowriders from rag tops for convertibles to Scale headlight lens and his wheels are best scale wire wheels period.

[@xsavagexhype181]

What servos are you running

[@NorthSideCustomRC]

AGF RC A81BHP hop servo and SA33 rear. A possible stronger and daster servo to be on test rig soon

[@Holmanrc]

What steering servo is that bro?