SKR 1.4 - Simple Endstop Switch

[@pradonegro683]

thank you, im learning a lot, good video.

[@munst1]

Thanks for this nice tutorial again and for your work what you doing for us.

[@EdwardBraiman]

You're welcome.

[@francoaloisi7615]

Hi man, I have this board, and I tried many times to config the endstop but they don't work, m119 say triggered, and when a press the switch m119 say open but the axes still moving, so in other video on KZbin we says this board have the wrong resistor for the endstop, what you think about? My endstop is meccanical with 3 pin, power, ground, ans signal, possible I resolve this problem if I cut the power cable? My first printer have a similar endstop but with 2 cable, ground and signal.. I hope in your reply, have a nice day

[@Bobby11]

So im replacing the board in a creatbot printer with a skr 1.4 because creatbot dont share opensource code... And i want to use klipper. Anyway, whenever i search for info i seem to end up on your videos. From klipper install to finding out how to connect 2 pin end stops. Im glad because your videos explain things well.

[@EdwardBraiman]

Thanks.

[@ujang0711]

Thanks for this. Definitely helped Getting my anet a8 wired for this board.

[@EdwardBraiman]

I'm printing the components for an Anet out now. Might do a video on how to build one in a livestream this weekend. Motherboard might be different, not process will be similar.

[@jurgenenders132]

thank you for this Video.I will learn about Pronterface G-Codes to test my 3D Printer.

[@EdwardBraiman]

You're welcome.

[@brandonhowes5364]

Thanks, but I ended up finding my real problem. My endstops were not being triggered at all, ended up being the diag pin on my TMC2209 drivers. I desoldered the pin and the endstops started to work. I hope someone else finds this useful.

[@elrobertvazquez]

Thanks! Can i do it in a skr mini e3 v2.0?

[@--3D]

Edward awesome video, I followed it and X works perfect. But I'm having problems with Z and Y. I can't get them to home, also when I home X first Z moves up a few cm and then X makes homing. Any idea that could help me? Thank you. I have an Skr 1.4 turbo with BTT TMC 2208 v3.0

[@-martintheengineer-7465]

Hello Edward. I love your videos. But the main point of the 1.4/Turbo board is an endstop on Z with TMC2209 will not work. I would appreciate a video that shows an endstop, or a probe (inductive, or BLTouch) with TMC 2209 and setup with the Z min plugins. Best regards Martin

[@skysi]

The v1.3 has a problem with this. There is a resistor soldered in, where it shouldn't. So you have to reconfigure the signal pin to a free other pin. I'm not sure if the v1.4 has the same problem, but maybe you check that.

[@andirahmat6689]

make sure that u not used sensorless homing with tmc driver?

[@EdwardBraiman]

Not sure yet, I'll need to research.

[@blake_0007]

Any idea why my Z axis won't go into negative?

[@EdwardBraiman]

Check for inverting direction in Marlin firmware in configuration.h.

[@ypsonar]

Hi, Very informative video, Is Switch normally closed or normally open . . . ?

[@EdwardBraiman]

Depends on switch type. Some switches have a circuit board that can reverse logic. Best way to figure out is try switch with m119 gcode and if logic is backwards change in Marlin firmware.

[@pierremarc-donaldjupiter7078]

It is a Great video

[@EdwardBraiman]

Thanks, it's a bit Old.

[@RyanSeeber]

👍