Be careful using those TB6560 modules. The data sheet specifically calls for the 5v logic to be applied to the chip first and be allowed to settle before the motor voltage (24v or more) is applied to the chip. Those module derive the logic voltage from the higher voltage using a 7805 thus compromising the power-up sequence. There have been reports of failed chips as a result. The problem can be resolved with a modification of the power circuitry.
@ArifFitrianto_edukasi5 ай бұрын
Bisakah saya kendalikan ini dengan bluetooth
@teodoropillagacardenas84513 жыл бұрын
Hi, nice video. I have a question... I connected arduino Uno, 3 nema 23 stepper motors and 3 TB6560, but the "Y" motor moves only one direction, the others work good. I used your setting. can you help me please. Thank you
@syedaliasad90632 жыл бұрын
Hey Alessio, which software have younused for making the circuit diagram, pls reply quick. Its urgent
@adrienhans51113 жыл бұрын
Hello sir, I using 3 Nema 23 approximatively 3amp each with driver tb 6560. For the power supply, I happened to have pick up a 12V 30 amp. Would it worked ?
@Artigiano20AlessioRomanelli3 жыл бұрын
Hello!!! 30 amp is very good, but 12v it's quite enaugh. 24v could be better!
@adrienhans51113 жыл бұрын
@@Artigiano20AlessioRomanelli I thought the 30amp will be to much in case the driver or stepper motor tends to draw more thus burning the system
@moorthimoorthi39085 жыл бұрын
I got 4 tb6560 bord and 4 NEMA 17 motors, how much volt & input in bord please reply sir
@Artigiano20AlessioRomanelli5 жыл бұрын
Depends on how many Ampere needs each motor!
@moorthimoorthi39085 жыл бұрын
1.5 amp
@Artigiano20AlessioRomanelli5 жыл бұрын
@@moorthimoorthi3908 1.5 x 4 = 6 A. A switching 24V 12A will be ok. Remember to set up correctly the switches on the right amp on each tb6560.
@moorthimoorthi39085 жыл бұрын
Thankyou , Thankyou very much sir
@Artigiano20AlessioRomanelli5 жыл бұрын
@@moorthimoorthi3908 you're welcome man!
@enricobrunetti95415 жыл бұрын
sei molto bravo a spiegare. mi piacerebbe vedere lo stesso circuito comandato da un joystic k
@Artigiano20AlessioRomanelli5 жыл бұрын
Grazie mille!! In effetti può essere un progetto interessante, avevi pensato a cosa ti interessava vedere? Variare la velocità e la direzione direi, cosa ne pensi? Ciao!
@enricobrunetti95415 жыл бұрын
@@Artigiano20AlessioRomanelli certo proprio quello. Magari
@Artigiano20AlessioRomanelli5 жыл бұрын
@@enricobrunetti9541 ok, lo metto in cantiere! :)
@d0tted7703 жыл бұрын
can nema 17 take 24 v? Or is the voltage regulated to match my motor by the driver
@Artigiano20AlessioRomanelli3 жыл бұрын
Hello! It's the driver that requires the appropriate voltage. If you have to drive a nema 17 by a good driver, may be it's a good idea to choose a 24v driver, like a dm542t, a digital driver easy and strong.
@d0tted7703 жыл бұрын
@@Artigiano20AlessioRomanelli No ,I meant like ,i have a tb6560 and my nema 17 runs on 12 v. .How many v do i need to power the board?
@Artigiano20AlessioRomanelli3 жыл бұрын
@@d0tted770 no, your nema runs at the driver voltage. Tb6560 needs 10v to 35v, but to drive a nema 17, 24v it's enaugh. Do you have the nema's datasheet? How many Ampere does it need?
@d0tted7703 жыл бұрын
@@Artigiano20AlessioRomanelli 1.8 Amps but the problem is that in the datasheet it says it normaly runs on 12 v ,so if i apply 24 v to the tb6560 ,will it overload the motor?
@mohitvashistha73545 жыл бұрын
why are you not connecting enable- to the ground pin
@Artigiano20AlessioRomanelli5 жыл бұрын
Because is not necessary. The motor is enabled by default. And i don't want to set enable off, to avoid the idle mode.
@safarzitoun65325 жыл бұрын
hi mr i need your progrmme pleas
@Artigiano20AlessioRomanelli5 жыл бұрын
AGGIUNGO LO SKETCH PER CHI VOLESSE PROVARLO! int Distance; int speed; int steps; void setup() { pinMode(8, OUTPUT); pinMode(9, OUTPUT); digitalWrite(8, LOW); digitalWrite(9, LOW); } void loop() { speed= 50; steps=6400; delay(1000); digitalWrite(8, LOW); digitalWrite(9, LOW); for (int Distance = 0; Distance
@safarzitoun65325 жыл бұрын
thanks a lot
@Artigiano20AlessioRomanelli5 жыл бұрын
@@safarzitoun6532 you're welcome!!
@aaamarco67265 жыл бұрын
buonasera volevo sapere se il disegno dei collegamenti lo hai fatto con fritzing. se si mi puoi passare il componente TB 6560 V2.0 DRIVER . Grazie s.agostinotva@tiscali.it