Float Switch Wiring Diagram for Water Pump/ How to Make Automatic On-Off Switch for Water Pump

A float switch is a mechanical switch that floats on top of a liquid surface. As the liquid level goes up or down, it moves vertically with the liquid level. This is a type of level sensor and this device is used to detect the level of liquid within a tank. And also float switch may be used to control a pump, as an indicator, an alarm, or to control other devices.
In this video, I have explained about float switch wiring connection to control a water pump.
What is a float switch?
A float switch detects the level of a liquid in a tank. Based on the water level, it will open or close an electrical circuit generally used to pump water in or out of the tank.
How to work a float switch?
A float switch moves with the liquid level up and down vertically. An internal mechanical switch opens or closes an electrical circuit with gravity. Therefore, the electrical circuit can turn on/off equipment, like a water pump.
What does a float switch do?
A float switch monitors the level of a liquid in a tank. It then opens or closes an electrical circuit based on the liquid level and wiring to control external components.
How to install a float switch?
A float switch is installed in a liquid tank. Firstly, a pre-set level is made and can be done with a counterweight. Then, based on a normally open or closed wiring configuration, it will open or close the electrical circuit based on its movement up or down with the liquid level.
How to wire a float switch?
A float switch is wired in either the normally open or normally closed position. A normally open position is open when down (low liquid level) and a normally closed position is closed when down. The open/closed position refers to the electrical circuit.
If you have any questions about float switch wiring, please comment below the video. I will answer your questions.
Thanks for watching this video.
PLEASE SUBSCRIBE THIS CHANNEL FOR MORE VIDEOS.
/ @slengineeringacademy2234
💻Connect with SL Engineering Academy
🌐Facebook 📲 / sl-engineering. .
More video
Complete Electrical House Wiring / Single Phase Full House Wiring Diagram
• Complete Electrical Ho...
Single Phase House Wiring Diagram / Single Phase DB Wiring
• Single Phase House Wir...
Two Way Switch Connection / How to Wire 2 Way Light Switch / Starecase Wiring with 2 Way Switch
• Two Way Switch Connect...
Automatic Changeover Switch for Generator / Automatic Transfer Switch / ATS (With Circuit Diagram)
• Automatic Changeover S...
DOL Starter Connection with Indicator | 3 Phase Direct On Line Starter/ Explain with Circuit Diagram
• DOL Starter Connection...
Star Delta Starter for 3 Phase Induction Motor / Star Delta Connection
• Star Delta Starter for...
Float Switch Wiring Diagram for Water Pump/ How to Make Automatic On-Off Switch for Water Pump
• Float Switch Wiring Di...
Float Switch Connection with Auto & Manual Selector Switch for Single Phase Water Pump
• Float Switch Connectio...
How to Wire Ceiling Fan and Fan Regulator / Ceiling Fan Connection / Fan Regulator Connection
• How to Wire Ceiling Fa...
3 Phase Distribution Board Layout and Wiring Diagram
• 3 Phase Distribution B...
Earth Leakage Relay - ELR / How to Wire ELR & CBCT with MCCB / Working Principle of ELR
• Earth Leakage Relay - ...
Single Phase Split Type Air Conditioner(AC) Indoor & Outdoor Wiring Diagram/ How to Wire Split AC
• Single Phase Split Typ...

[@slengineeringacademy2234]

Thanks for watching ❤👍 Please subscribe this youtube channel to watch more important videos like this..

[@apolinarpolomarrugo8174]

@Salman khan Mon

[@atanlap]

low water level blue and black connected. high water level also blue and black connected.. so, when the water pump should on and off?

[@charlesmimbe5171]

@@atanlap low level: blue and black, the pump is on. High level: the pump is off automatically. The blue-black connection remain.

[@CommercialGasEngineerVideos]

Thank you

[@danielteyehuago1633]

This is very educative, thanks for sharing it with us...

[@ericapanama503]

Excellent simple to follow video !! THANK YOU !!

[@thakbhnbuccugughchdmmilsel7535]

Explanation with circuit is appreciable. Circuit with components is also appreciable.

[@najibatulmysha62]

Thank you so much!! Your video helped me figure out the wiring for a project I was making.

[@techabbas5128]

Beautiful video sharing

[@slengineeringacademy2234]

Thank you.❤👍❤

[@danielteyehuago1633]

Thanks for sharing it with us

[@NgouanfoTV]

Nice video its really help me 🙏 please boss of how to connect my pump with two fload switch thanks

[@milkyway808]

Wow very helpful and very nice 👍

[@ravinderbansal1418]

Excellent 🙏

[@slengineeringacademy2234]

Thank you.❤👍❤

[@amsnsangwa6450]

Merci beaucoup pour votre aide

[@kwamepeters2616]

Thanks

[@mr.electrical360how]

Good work sir

[@coffeepp4335]

Great video! Is it possible to make the pump turn on when water level gets too high to pump out the water and stop when the water level is low? Thank you

[@Evoluzione2]

That would be more useful and just what I need too.

[@vaio4908]

Yes, you need to wife the float switch opposite as in the video.

[@sikandaralam4217]

Fantastic information sir.

[@slengineeringacademy2234]

Thank you.❤👍

[@zahoorkhan4052]

Nice 👍

[@slengineeringacademy2234]

❤👍❤

[@bahriakyildiz3054]

Thanks a lot dear excellence explained

[@Yad_Esi]

Also about uv sensor

[@bungaizhrin2705]

This is for single phase pump.. can 3 phase pump apply the same for the float switch installation?

[@lisandromanueldiazamador8494]

Why you did connect the float switch to the N line of the contactor control circuit instead of the L line? What's the difference between each connection?

[@vimalnath8886]

I’m also having that same doubt in my mind

[@raphaelu3649]

Yes. Same here wth doubt.. Whyy??

[@hawre95]

because it is safer!

[@raphaelu3649]

@@hawre95 tq for the reply.👍👍

[@iskandarmegat112]

This diagram make we thingking over

[@majidshah7868]

Thanks bro

[@brentwilliams191]

Looks like your switching the Neutral to to operate the Contactor Coil. In New Zealand Wrong, Neutral is not switched at all, so only Single Pole Circuit breaker and contactor used. You would use a Control C.B. as well

[@freeiphoneblob]

Hi, I’m looking to make this. Could you help me understand how to do that? My email id is [e-mail] I’d be really grateful to you for your help! TIA

[@iskandarmegat112]

Yes In My country we not use this diagram but ... inside bideou diagram controller function as well

[@ferrari4150]

Very nice.....

[@slengineeringacademy2234]

Thank you❤

[@henryamri6104]

Can such a floating switch control two separate pump at same time , like NO to stop pumping and NC to start pumping (to use common for both pumps and NC for one pump and NO to control another pump)?

[@iskandarmegat112]

Yes aslo can sir

[@DIYUKSA]

GOOD

[@marvelkayferfejer8022]

is it the same for line to line connection?

[@nancypinto-nh6ms]

Its not advisable to have AC.supply in the water no doubt the floatswitch is compact,it could result in shock due to leakage

[@yoy-gul6447]

gud day sir what if my waterbpumpbis submersible then i did not ise a magnetic contactor, instead i directly put the float switch directly?

[@chrisb8362]

It appears you are breaking the N and not the L, would also recommend an isolated low voltage control circuit. Where is your coil contacts, I assume they are the two on top otherwise you would have a short, I.E where is A1 A2 coil terminals.

[@Technical-Mindset]

Thnx ❤️👍

[@slengineeringacademy2234]

❤👍

[@waqasakram2857]

hi i got problem my relay making chattering sound some time high some time Low. Let me know is this worry thing?

[@jamessmejkal8803]

Try cleaning the contacts with a nail file or fine file

[@rahumathullaha8238]

ஸ்பீச் ஓட இருந்தா நல்லா இருக்கும் இதைவிட

[@prarthanaanilkumar6579]

5ampere current edukkunnu switch on aakumbol thanney pinney work cheyumbol athreyilla enth cheyaam

[@mr.electrical360how]

Kon se app use karta ho hand animation driving bna na k lya tell me please .

[@hasanaliozkaya228]

hello, thanks for the video. Which animation program did you prepare the video with?

[@amitmondal96969]

Sir a single pole single fuse. contactor se ho sakta hai kiya.

[@eddiedeleon2425]

liquid level control

[@ramborums]

Is it safe to use float switch in water tank? Is there any possibility of electric leakage?

[@josievillamin4671]

May I please know the specs of the magnetic contactor single phase and where to buy it? Your response will be greatly appreciated.

[@paulocalixto1057]

Excelentes vídeo. O problema é que não é português.

[@mycats7321]

I'm not really familiar with the MCB thing. I have a 1HP 12.2/6.0-6.1A 115/208-230V air compressor pump. It has a black wire, a white wire, and a green wire. I *think* it is 2 hots and a ground. It currently connects to a D-box float switch with a lever that is moved by a rod with a float on the end. Unfortunately, it keeps getting jammed & keeps the pump running so it overflows the cistern. I want to have the pump turn on when the water is low and off when the water is high. I get L= live (hot), N= neutral & green is ground. So, it looks like the power supply wires connect to the MCB but ground goes directly to the pump but I'm slightly confused about the red wire from the MCB. Is it spliced? Why does it seem to go further in to the contactor than the other wires? Is it connecting at a different point? Is the blue wire also spliced with a black lead to go to the black? wire of the float switch? Also, what about that unconnected red wire on the float switch? Does it just say disconnected? Is the MCB really necessary?

[@XloMotion]

Black = power White = neutral Green = ground That's the color designation of US wiring

[@sukshr]

What will be problems if i not use relay switch and want to connect directly in motor pump???

[@alexanderchatz9617]

Γνωρίζει κανείς πως μπορούμε να συνδέσωμε τριφασικό βάτραχο σε φωτοβολταϊκά; Ευχαριστώ πολύ.

[@kouamekouakouraphael2259]

Supert

[@tecnoservicessecurity8517]

Good afternoon which program you use to animate your classes, because I need to give classes to my students.

[@brewyaaa]

would you be a sport and share the PN of these contactors?

[@mgold4685]

Solar pump controller on Etsy

[@norbertoalba1964]

Paano po kung ang soply ng tubig galing ng water distric, walang motor,,paano po cocontrolin ang tubig pag puno na

[@sayekhmonir8686]

Please give me a three phase connection video

[@venkatkumar7662]

Amazon link to buy magnetic contactor and float please

[@hajadaac3688]

Contactor model and amazon link please. And can we mount this contactor in wall

[@premilshasendra2746]

where can i buy such a equipment ??

[@k.raghavendra534]

I hope the connection was wrong definitely .Sir

[@abdouliedibba2312]

what is the specification of this contactor? Thank you

[@agussulistyo6718]

👍👍👍👍

[@ravitv177]

Why we have to use contactor? We can directly connect the phase line to float switch right

[@mohammedal-daini8790]

I expect to avoid electric shock in case of water leakage in the floating part

[@mangalapradeep4813]

💪💪💪💪

[@slengineeringacademy2234]

❤👍👍

[@kalyandey83]

Magnetic contactor link

[@khezransalik9963]

They are series of events in logic boards and calls and labyrinths chain of command series of events calls .................................................I still don't have matatu fare office number

[@KhalidKhan-khankhalid]

I think it will not work, Where is A1 & A2 connection, & why do you connected L, N both to float switch.

[@iskandarmegat112]

Make me thinkinh over

[@solution1988]

بیٹری اور سولر سے خود موبائیل چارجر بنانا How to make 12 volt DC Mobile charger. कैसे बनाये 12 वोल्ट डीसी मोबाइल चार्जर kzbin.info/www/bejne/n32wm3ujrqiCeJI

[@lijukadayil4959]

220 v not safe, use 24 v dc relay

[@silvioadeodatoferrirafilho4724]

Teria aulas em português

[@innocentprince7188]

ফ্লট সুইচ এর দম কতো?

[@bjs1984]

මේ විස්තර සින්හලෙන් දාන්න..

[@rozanarozana3194]

Subtitle pls