Sloppy BMW? // 034 Motorsport Subframe Inserts (Install DIY)

034 Mounts and Inserts: goo.gl/8xa92h
New Hardware: goo.gl/V5oR21
Is your BMW feeling a little sloppy? The guys over at 034 Motorsport have a great solution. Their new BMW mounts and bushing inserts are a great way to firm up your BMW E90, E91, and E92 (non-M) chassis car.
Their 50a durometer solid rubber engine and transmission mounts and billet subframe bushing inserts are easy to install, but make a noticeable difference in overall vehicle feel.
In today's video we show how to install their rear subframe bushing inserts on a BMW E90 330i. The install is fairly straight forward with basic tools, however new bolts and an alignment are needed.

[@bungl3971]

I was just watching a Donut Media video and did a double take lol

[@billbeuginton9742]

I just saw Job in a clip that was referenced to this channel not Donut and I was like, waaaaht.

[@randallprince]

JOB!!!!!!!!!!!!!! So much excite!!!

[@Yo-shi-t]

What’s the hell its the donut media guy

[@micraw714]

Just ordered these along with ECS front and rear sway bars 😁

[@mikeastewart]

Please get back to the winter better stuff I was loving it.

[@ecstuning]

We are! Lots of content coming soon.

[@GustavCarl17]

I came here to say the same thing. The beaters give me bad ideas, but I still like watching them do it. I want a beater, but I don't "need" a beater

[@ecstuning]

We'll be putting out an episode about Zach's E32 in a few hours! Hang tight!

[@pinoysi06]

Some Bmw love from ecstuning🔥

[@gideonbouwman4904]

Will this also be available for the BMW E39? I'm driving an European spec 520i manual, shifts are spot on, but i can feel a little play in the drivetrain, i think this will take care of it :)

[@rweber5332]

Wait a second… i know that voice anywhere!! It’s Jobie!!!

[@DigitalDissident]

Very good video

[@ColinMcEvoy]

boy howdy do i sure like my rear ends tight

[@dookie177]

Anything for the f3x chassis?

[@jcchin512]

After install the car will feel any vibration when the car stopping ilde time?

[@mrboostification]

For e60 also?

[@7soldierjc]

please change piece of jetta mk6

[@desmondmoonbear4143]

Bimmer are best

[@BMWI-gk9wh]

Yup my n51 and n52 both lasted 250k no problem

[@anthonyclayton243]

How you managed to say "We all need to tighten up our rear end" without laughing is beyond me...

[@towhee7472]

How in the fuck did youtube show me THIS a week after those sub frame bushings on my e90 went to hell? This is skynet level fuckery!! Also I'm buying most of theses parts, lol.

[@icommandoi145]

The M spec bushings are different to the ones you showed here. When comparing my 335i N54. Would these inserts still apply? I believe the M spec have a different insert by factory built-in. Can you confirm?

[@unluckeeeee]

M spec bushes do not need inserts. The 135/335 bushes are hollow, m3 are not.

[@unluckeeeee]

No... M bushings are not hollow, they are full. Inserts are only for non m models.

[@swerveo7313]

Just get m3 bushings

[@unluckeeeee]

@@swerveo7313 Huge job compared to inserts.

[@Sideways_N55]

M spec is only interior and exterior appearance, same bushings.

[@JuergenQingdao]

Why are those 034 inserts “Only available for purchase and shipment within the United States” ?

[@jjturner7463]

woa wtf, i didn't know hw used to be with ECS tuning

[@Gon_Eyes]

awesome vid! 2015 330i m sport 18k making a hard click or sharp clunk noise going up driveways is this a fix for it too? thanks

[@lowes1388]

So if I do this in my garage . I’ll jack up the car with two jack stands and use my lift to raise and lower from the rear diff ?

[@amcheung10]

I recently installed these on my E90 330i, and did exactly that. I used 2 jack stands in the rear, and used a jack to help support and lower/raise the subframe as needed.

[@losidude11]

@@amcheung10 was it worth it?

[@cejsi]

@@amcheung10 worth it?

[@gordythecreator]

Thought I recognized that voice

[@TheHeretic435]

How is solid rubber engine mounts going to improve handling? All you'll get is more vibration in the cabin.

[@BMWI-gk9wh]

Not true. There is still play, the vibrations from engine are decreased by giving a stiffer less play bushing

[@BMWI-gk9wh]

Gives less play more stiffer and consistent power

[@MsJohncarpenter]

is this if rear bushings are good?

[@ecstuning]

Yes, we do recommend if your bushings are bad, replacing them and THEN adding the insert mounts

[@aaronlaughlin1792]

Do you know if they plan on making this same kind of kit for the e82 chassis?

[@peterwinegardner1608]

These fit E82! www.ecstuning.com/b-034motorsport-parts/bmw-e9x-rear-subframe-inserts/034-601-0047~034/

[@jamesm6918]

@@peterwinegardner1608 is the process to fit them onto an e82 (1 series coupe) just as easy?

[@Turbo2Pete]

OK - at 8:03 "47Nm plus 90 degrees" NINETY.... You then put a breaker bar on and cranked it 90 PLUS another 90 - 180 degrees! I'd not be surprised if those bolts fall out in a few hundred miles. Yikes.

[@justint5387]

There were 2 bolts

[@Turbo2Pete]

@@justint5387 You're right! - man, I watched it over an over too... hard to see, with hands and plastic in the way, but now I see it is indeed two...

[@TheHeretic435]

They slam the parts in.

[@ginaghgfysfghbg7044]

A lot of freakin' work!!!!!!! F*****!!!!!

[@lewis72]

Don't these subframe inserts just short-out the subframe bushes ? My guess is that the bushes are there for a reason and BMW knew what they were doing.

[@goorackerelite]

yes and no. BMW softened the subframe bushings to counteract the harshness of the Runflat tires. but the first thing to do is toss the RFT's in the trash and adjust the subframe and sway bars accordingly.

[@thedetailingdoctor5746]

Donut media again lol

[@AlexCapi]

£200 for these, what a joke.