And Shake n Bake can be the name of the first album
@arthurmead53413 жыл бұрын
Or a sex move
@pulsiui40033 жыл бұрын
@@arthurmead5341 I used to do the head thrust back in my pre e.d. days.
@je-2024_13 жыл бұрын
\m/ IIII] ; )"" \m/ IIII] ; )'''' ROCK ON
@justjimmy41713 жыл бұрын
I tend to think for most civilians, they aren’t in dusty environments and rarely clean their guns. Thus tending towards overlubrication will better protect the gun without causing malfunctions. I also find wet guns are easier to clean any grime is suspended in the oil and easily wiped away whereas dry guns seem to have the grime more baked in.
@scabcrawler6323 жыл бұрын
Rural Iowa is dusty as hell. Gravel roads and big equipment
@shawnr7713 жыл бұрын
Be careful of putting too much into the barrel. There is a potential although minutely small that it will attract enough dirt to cause a barrel blockage. We were warned about it in the Army. After storage always run a patch through the barrel before firing. Especially after long term storage.
@dontneedtoknow58363 жыл бұрын
@@shawnr771 the only lubrication of the barrel should be while cleaning with a wire end. If you even put a drop on your swatch you are doing it wrong. Treat it like a cast iron skillet man.
@shawnr7713 жыл бұрын
@@dontneedtoknow5836 Correct but some people put oil in the barrel and leave it there. It attracts dirt and grime.
@foxsquirrel30383 жыл бұрын
No such thing as too much lube when you want good “head thrust!” 😂🤣😂🤣😂
@whiterook84833 жыл бұрын
I was thinking but not saying.
@gfarrell803 жыл бұрын
"Just use the proper amount of lube"
@666BIGBLOCK2 жыл бұрын
Slow your head thrust. Your parts will last longer.
@murkyturkey52382 жыл бұрын
I use a gross amount of oil and never had a problem so far
@harperhellems36483 жыл бұрын
I timed sipping my coffee with Caleb and Steve. I experienced one of the weirdest feelings in my life ever.
@CalebSavant3 жыл бұрын
That feeling is known as the smyth effect.
@opencarry38603 жыл бұрын
If you live on the Oregon or Washington coast, you can't have to much oil. Trying to stop rust living in those areas is a constant battle.
@mattfleming863 жыл бұрын
Agreed. I'm on the other coast but have my AR daily on the farm. Rain or shine (or snow or dust) I try not to keep it dripping wet, but a "dry" surface will become a corroded surface in no time. Wipe everything off every week or two. Mop out the chamber (hay is JUST thick enough to potentially block battery) and air hose the fcg and empty upper. Takes minutes and I'm ready for another round. I periodically pop a steel target just as a function check and so far have had zero problems. My ONLY issues are going from unloaded to loaded while on a motorized conveyance. Probably need to pick up a single feed mag block or something similar to plug that hole. Remember to dot lube on optic mount screws, handguard/attachment screws, etc. AR's are amazingly ingress-resistant systems.
@MarkiusFox3 жыл бұрын
Which is why I would seriously consider a stainless steel firearm for high humidity. Or in the case of an AR, insist on a chrome plated BCG and stainless barrel.
@abandonbelief3 жыл бұрын
@@MarkiusFox all metal even stainless rusts and pitts though
@mattfleming863 жыл бұрын
@@MarkiusFox I'm probably going to try chrome or nitride on my next one (pile o misc. parts right now) but I have to admit that because the action is closed, i've never spotted a single speck of rust inside the reciever. I do love stainless barrels though! I don't own a single CL barrel. I really don't mag dump, so even with my LW rifles i'm a believer in accurate deliberate fire, and accurate is easier with better tubes. When I practice I usually stick to drills with lower round counts per rep. A good double tap or two low one high will deal with almost anything. x3 targets is still under 10 rounds. Give it a good cooldown and run it again. I have plenty of fun and never have had a barrel too hot to touch. I'd like to try a nitride barrel. Seems to he a good middleground.
@Lucas12v3 жыл бұрын
@@abandonbelief true but it corrodes far less easily. Several companies make rifles with stainless and then ceracoat it black or other colors over the stainless. In my experience, those are very rust resistant. Still, oil is your friend of course.
@bobhaehn54703 жыл бұрын
The worst I've seen from over lubing is that the operator will wear it when it comes out in a gas driven and bolt velocity mist
@shawnr7713 жыл бұрын
Hot CLP is always good hitting the eyes and face.
@tacticalbaydotorg78163 жыл бұрын
@@shawnr771 oh baby
@shawnr7713 жыл бұрын
@@tacticalbaydotorg7816 Sick puppy.
@wintersguo80483 жыл бұрын
Maybe do a video to demonstrate what would you guys consider the right amount of lubrication?
@eddiemoney93713 жыл бұрын
I was sitting here thinking the exact same thing
@KenneMCL3 жыл бұрын
They have several videos on their channel do a quick search but here's one kzbin.info/www/bejne/bHbYmoiehbGcnKM
@voltic71333 жыл бұрын
kzbin.info/www/bejne/bHbYmoiehbGcnKM They made this video that is similar you what you're asking about.
@CalebSavant3 жыл бұрын
We have plenty of them on the channel
@Portuguese-linguica3 жыл бұрын
Spit in your hand and rub all over you're rifle . That's always the right amount of lube .
@mmgee3 жыл бұрын
I spent 9 years working a private gun range, nearly every gun I ever opened up was bone dry. Many AR’s had never had the pins out
@ratagris213 жыл бұрын
Lazy weapons owners. Maybe they read the old AR manual where it was never meant to be cleaned.
@bansteban1353 жыл бұрын
@@ratagris21 you CAN not clean it if all it is is carbon. But sand/dirt/mud/dust you should clean. But you SHOULD still lube it.
@HelloImKowaBunga3 жыл бұрын
this makes me feel better knowing I have fired my ar only once but I have broken it down/cleaned it a dozen times. care for your firearms
@ratagris213 жыл бұрын
@@HelloImKowaBunga at least you keep it clean and in working order. Others are too lazy to clean it and care for it. I ran into some who purchased a pistol drive AR only because they like cleaning the DI rifle that had. But didn't want to buy an AK. They wanted an AK in an AR just be lazy. Slackers.
@richardlahan70682 жыл бұрын
I clean my guns every time I shoot them. Just a habit that I picked up from my dad.
@ryanbond32593 жыл бұрын
One thing I’d like to see y’all cover is the types of lubrication available, their uses, and the pros/cons of them. Specifically grease, oil, and clp products. Y’all are super informative as always! Thank you for what y’all do!
@tonydeaton28903 жыл бұрын
I've actually seen competition shooters spraying lube into AR15 ejection ports between stages.
@ericsmith59193 жыл бұрын
That seems to be a common theme. Guys who 'know a lot about guns' say don't over-lube, guys who run the crap out of their guns drown 'em in the stuff. Who to believe? It's up to you to decide.
@tonydeaton28903 жыл бұрын
@@ericsmith5919 I believe the pros. I run my AR's well lubed. Same with 1911's and just about everything I shoot.
@gregz4249 Жыл бұрын
I run lightly lubed as I hunt coyotes in very cold weather, had a buddy once over lubed his bolt and firing pin very sticky in the cold
@whiteyfisk97692 ай бұрын
@@gregz4249you just wanna lube the carrier rails on the BCG of an AR. Greasing the rest of it doesn't do a thing in regards to lubing the movement of it. Maybe one drop of oil on the firing pin to keep it anticorrosive.
@albertforletta149826 күн бұрын
I love all this high tech genius talk. Always believe the guys who “run the crap out of their guns.” I pour on the oil heavy! Never had a problem with over lubing. Just check the temperature ranges of the oil you’re using. 54 years I’ve shot thousands of rounds in all weather conditions. Never seen this mysterious dirt attraction, nor have I ever seen the mysterious gum that people tend to see in their guns. What is this mystery gum? Wrigley’s? Clover???
@silvergrizzly3163 жыл бұрын
I just took apart my BCG on my 15 night b4 last and I remembered Caleb's previous video on this subject so I'm good ta go!!! Thanks Caleb and Steve!!! 👍👍
@robertsimpson32253 жыл бұрын
It’s not necessarily that it will attract dirt/dust. It’s that the lubrication grabs/holds onto whatever dirt and or carbon that comes into contact with it. That said, the additional lubrication will then coat and “neutralize” the dirt and still maintain a low coefficient of friction. So in effect, the abundance of lubrication is able to overcome a certain amount of dirt due to the shear amount of lubrication.
@gunsandcars36483 жыл бұрын
clean after use, lube reasonably , check actions, wipe any excess and she will run all day
@rick-kx7gy3 жыл бұрын
Okay that takes care of the wife now what about the guns ?.
@gunsandcars36483 жыл бұрын
@@rick-kx7gy I just waiting for someone for this...finally.
@iamgermane3 жыл бұрын
Prone to failure anyhow!
@joncampo16273 жыл бұрын
I’ve got 30k through one of my BCM’s and I lube it after every one or two uses but only half ass cleaned it 4 or 5 times. Runs like a champ
@iamgermane3 жыл бұрын
@@joncampo1627 Troops in Afghanistan had their M-4s fail on them in combat.
@saxmusicmail3 жыл бұрын
I have seen new AR shooters at the range having problems, then found out that they were "runnin'' her dry like they do in the 'sandbox'". Well, the US isn't a sandbox. I have fixed their rifles by turning the rifle on its side and dropping in a good squirt of CLP. Voila! It is functioning perfectly! Excess lube will just blow out of the ejection port. But no need to overdo it. Do keep the firing pin and firing pin channel wiped dry with a pipe cleaner.
@qutaurisparker32993 жыл бұрын
Thanks guys great video just bought a brand new Smith & Wesson ar15.
@PuppetMaster17913 жыл бұрын
Solid choices with the M&P15. Not the fanciest rifle on the marked but great overall, especially for its price point. We have ran them in our rental fleet for years and they have held up better than most, including some that cost a few hundred dollars more.
@Jennifer_Prentice3 жыл бұрын
I had some minor issues with mine but after tearing it down , Facing off the upper and putting all new goodies on its a great gun :). Most of those are very basic and come with the plastic hand guard and stuff. I found it was a good starting point to build a great AR. You can take your time doing the upgrades and the gun is still all together so you can still shoot it while doing upgrades .
@StrideResearch3 жыл бұрын
Now you need a light and a sling! Check out StreamLight HLX for a light and Vickers tactical sling!!
@abandonbelief3 жыл бұрын
All I have is a gun vise ordered today ... plans to build my own since waiting lists for parts exercising my patience like Arnold
@animalmother59023 жыл бұрын
Get a new handguard for it the factory one has no heat shield
@geofftimm22913 жыл бұрын
The US Army in the 70s said, "Wet not white" on the bolt and carrier. Not so much on the buffer and internals. Some Drill Sergeants took it to extremes. Geoff Who has been around awhile.
@hwsadberry67813 жыл бұрын
My Gov't issued M16A1 which was prone to malfunctions in the upper needed graphite to take up the space between parts keeping the parts from slapping around. I would clean everything normally except the upper which required nothing more than a quick slosh in the cleaning solvent barrel and more graphite added after drying. My consistent 40/40 on the popup range was proof to others how to avoid the notorious jams of the A1. Once the A1 was retired and the uppers were made to order instead of using drop in parts the jam issues went away. I know this was a bit off topic but your awesome video brought it to mind. Have a great day!
@rogerpemberton793 жыл бұрын
The over lubrication idea has always made me chuckle. A gun is a simplified machine. Some think guns can be over lubricated yet they pour a minimum of a gallon of oil in their vehicles engine for an oil change. Sewing machines are heavily lubricated, some even have oil sumps like an engine does. The point is machines have to be lubricated. I've shot some M16's and M60's in the Army that ran better (read that as reliably) when lubricant was coming out of them as they were being fired. I also enjoyed Larry Vickers engine oil demonstration as it does drive the point home. As for the carbonization of the lubricant just use a very high flash point lubricant. I personally use G96 on all of my AR's for many reasons including that one.
@darthhodges3 жыл бұрын
So as with so much in firearms and life, moderation in all things.
@ftswarbill3 жыл бұрын
You guys are always such a good watch. One of my favorite channels!
@WiliamShattner3 жыл бұрын
They talked about “too much head thrust from using too much lube” without even smirking.
@AndyCigars3 жыл бұрын
Iron wills on these guys...no doubt at all.
@AndyCigars3 жыл бұрын
Ahhh, that synchronized sip at the end. 👌🏻
@blckandwhtknight3 жыл бұрын
Probably worth mentioning that excessive lube in the chamber of bolt face can cause dangerous pressure spikes in a tight chamber. Storing an over lubed firearm, loaded and muzzle down is asking for trouble. Lube in the bore isn't a great idea either, unless you absolutely need it to keep corrosion out.
@PetuniaIii-pd1ww2 жыл бұрын
Never considered that but i can see the point...we run an oily patch and a dry patch usually and I will have to think about this...
@bonjovi27578 ай бұрын
Not doubting what you say at all, but I always store my guns muzzle down with wet chambers. Haven't had a problem yet. Maybe I've just been lucky for 10+ years. I don't know.
@albertforletta149826 күн бұрын
@@bonjovi2757, you won’t have any problems. I always have a light film of oil(Ballistol) in my gun barrel, and I don’t remove it before I shoot. When I shoot hardcast lead out of my revolvers, the wax lube ring on the bullet lubes the bore with every shot. The wax in the bore helps to lessen the lead build up in the bore.
@MyWatchIsEnded3 жыл бұрын
Info about not oiling the rear of the bolt in the bolt carrier group is very important info I've never heard before. I had no clue it was supposed to be dry behind the orings tbh.
@CaptainCiph3r3 жыл бұрын
It's not true. It doesn't matter. Lube will work its way in there from the bolt stem. The statement about not oiling the gas rings is an old myth. Any lubricant there will be burned off. It will cause literally no issues. The fear is it will cause the gun to cycle faster or something bullshit like that, but time and again it has been proven that the gun doesn't even need gas rings to run reliably, lube isn't going to hurt them.
@edder71573 жыл бұрын
Just use CLP. In the military, ppl would lube the hell out of the weapons. They wanted to go home after shooting as quickly as possible so they hosed it down. The only warning CATM would give is DON’T use CLP on the gas rings. Oh, and ONE DROP for the firing pin, ONE DROP for the extractor on the head of the bolt after assembly, then wipe it. Other than that, the only thing they said upon inspection was, “wipe off the excess, I don’t want oily hands “, if you cleaned it enough.
@samspace813 жыл бұрын
lol you guys always bring back fond memories of sitting with my grandpa and talking guns
@GeorgeCowsert3 жыл бұрын
I wanna be put down in the history books as that one guy who dunked an AR-15 in a drum of lube. Problem is I don't own nearly enough lube.
@abandonbelief3 жыл бұрын
Thats what she said Buahha ha
@Pyreleaf3 жыл бұрын
Just pick some up at the next family reunion.
@jakegarrett81093 жыл бұрын
I thought that was normal procedure (it's a good method for any metal that needs major cleaning, like engine/trans parts and let it soak for a couple days to loosen any rust or grime). I've heard many people did that for storage in 55 gallon oil drums, at least back in the day it was common practice and I've done it with pellet and BB guns that had some surface rust and it helped letting them soak before giving them a good scrubbing and clean up, so it should work the same for real firearms.
@onpsxmember3 жыл бұрын
It's been done, so jut watch it here on youtube. Larry Vickers did that to prove a point.
@badmoon75493 жыл бұрын
But what if Caleb gets too much lube in his hair? Will that make heads thrust?
@rick-kx7gy3 жыл бұрын
He's got that covered . The sideburns wick off the excess .
@badmoon75493 жыл бұрын
@@rick-kx7gy now that's funny. Caleb is a good guy to put up with so many comments on his hair.
@rick-kx7gy3 жыл бұрын
@@badmoon7549 he's a big boy and knows he's appreciated . and offers really good info . same with Steve . And Brownells is half of number one with Midway USA .
@annverleedowns3113 жыл бұрын
Oh I thought it was a plastic taupe like on a Lego person the grandkids play with
@colby76253 жыл бұрын
Had to have learned it from an old timer.
@Iceaxehikes3 жыл бұрын
I over lubricated a Marlin Papoose which was my first gun. Not knowing any better, i would spray lubricant into the action which deteriorated the bolt buffer to the point it cracked. Many years later I still have that Papoose with a new buffer and it is clean and dry now. I keep only the lightest film of oil on the side plate assembly, applied with a q-tip, and leave the buffer dry. I have gotten away from aerosol lubricants applied directly to things. A drop of oil on a q-tip or patch. I use aerosol on a rag and use the rag to wipe the outside of receivers and barrels. Less is more.
@BrassCatcher3 жыл бұрын
Only time i aerosol is when I’ll be blowing off access
@steve90983 жыл бұрын
Great video guys. Please do a video on proper lubrication, and be sure to demonstrate where to lube and where NOT to lube the AR-15. Thanks!
@CalebSavant3 жыл бұрын
We have several! Check out our other playlist.
@rw75943 жыл бұрын
Good point you made about lubricating inside the bolt. I'm in Alberta Canada and a couple of days before a cold hunt I spray Remington Action Cleaner in the bolt to clean it out. Brake cleaner would work also. Last thing I want hunting during a cold day is for the parts inside the bolt to freeze and seize. Click and no bang means good meat runs away.
@oceandmike3 жыл бұрын
Great content! Thank you.
@MZ-rn3xq3 жыл бұрын
Thanks guys!
@CoolestDude38NC3 жыл бұрын
My rules for firearm lubrication are simple. 1) keep lube out of the chamber, bore and also off the ammo and magazines. Getting lube on any of those can cause too high pressures. 2) on AR direct impingement rifles, keep the entire bolt carrier group wet and use one of the modern synthetic CLP lubes that do not burn off during heat...SLIP2000EWL or full synthetic motor oil are good for the bolt carrier group. 3) For the exterior of the rifle use a light oil that does not attract dirt, leaves and grit if I have to get down on the ground...BF CLP. 4) I don't go by what soldiers and Marines claimed worked good as a firearms lube over in the middle east because that's a totally different kind of climate and terrain than where I live in the southeast USA. The middle east is super low humidity and lots of sand and in some areas, fine talcum powder like dust. Where I'm at my climate and terrain are high humidity, rain, hot and humid in the summer and cold and wet in the winter. And there is no sand or fine dust where I live. So individualize your weapons lube for your particular geography and climate.
@colsoncustoms89943 жыл бұрын
You guys may have just solved a mystery I had a few months back. I dialed in the gas settings on my lr308 for a hand load and put the rifle away. Came back about a year later and couldn’t get it to cycle that same load without changing the gas setting. I’m betting I had it running while everything was wet and the lube dried out / ran out overtime causing more friction.
@jasonlopez48552 жыл бұрын
My LR-308 bolt will not run dry has to be wet at all times to work. I put a 243win barrel on it even worst the bolt doesn't feeding rounds in or out. Getting better. DPMS keep it wet.👍🏽 I really like my rifle in 234w or 308w
@colsoncustoms89942 жыл бұрын
@@jasonlopez4855 wetter is better 👍👍👍
@phtevenmolz50303 жыл бұрын
There was almost always that one person in the Army that was working range detail and demanded everyone entering the range get a couple squirts of CLP from a spray bottle. Only because someone before them had done it without understanding the consequences. Monkey see, monkey do. Those were always the worst days on the range for malfunctions.
@CaptainCiph3r3 жыл бұрын
If its not leaking from the pins it needs more. The gun will get rid of what it doesn't need. Gun will run full of sand, won't run dry. The comment on not getting it on the gas rings is wrong. One of the main points that needs lots of lubrication in the bolt is the cam pin path and cam pin itself, lubricant put in this cutout will work its way onto the gas rings. This doesn't hurt anything, it's a myth just like the "if you take out the gas rings your gun will blow up" crap. Just not true, lube will get in there and very quickly burn off. I suggest referring to SOTARs video on lubrication for the BCG. As for attracting dirt, ANY lubrication attracts dirt. What many people have found out running guns in the sandbox, is that if you use enough lube the grit and dirt becomes neutralized by the lubricant. If you don't use enough it binds things up. If you wanna experiment, put a drop of soap on your hand after grabbing a handful of dry sand, rub your hands together. Note how it grinds in your hand and causes friction. Now pour a little more and repeat until the sand is floating around in the soap and your hands glide across each other smoothly. As for firing pins, firing pins should be dry. At the most it should be lubricated by whatever seeps in around the bolt, and should be taken out periodically and wiped clean. Never lubricate the bolt face ALWAYS lubricate the locking lugs Lightly oil the extractor at the rear near the pin Never lubricate the extractor claw. Front gas ring on the bolt stem should be lubed. Rear gas rings don't matter either way, they will get lubed whether you intend it or not. Bolt tail behind the gas rings should be lubed unless you like scraping carbon all the time. Bolt stem should be lubed fairly heavily. Cam pin and the path it rides in is the most violent and overworked part of the entire gun, and should be near packed with lubricant, push the bolt head forward, fill the chamber the pin sits in, push it back, fill the front side of the chamber. Bolt rails are the only thing external on the carrier that needs to be lubed, but general rule is just put a little on your hand and get it all over the front of the carrier from the edge where the bolt protrudes, to the rear where the rails end. Do not lubricate the bolt carrier tail, not because it will hurt something, but because it is a waste of lubricant, that part does not touch anything and does not produce friction worth noting, lube there is just wasted. A drop on the hammer face, a drop into the disconnector and sear, and a drop onto the safety, as well as one drop occasionally into the takedown pins. Remove buffer and spring and essentially dry your hands with it. Whatever lube is left over from the BCG just run it down the spring and buffer. Failing that, just one or two drops to the palm of a gloved hand, massage it in. Not totally necessary but it cuts down on noise and doesn't effect reliability adversely. Following these steps I've gotten guns to run for months on one lubrication, with more than ten thousand rounds in between cleaning of mixed supressor and non suppressed fire on some guns.
@peterresetz19603 жыл бұрын
I use Lucas Gun Oil for springs and hammer and trigger pivot points, Shooters Choice grease for slide rails, and bolt lugs, and Chip McCormick Trigger Job grease for hammers sears for a long time. Lucas Gun Oil is great on reciprocating parts such AR BCG, because it’s just thick enough to not shed off when the bolt is cycling, and will keep carbon fouling from building up. Shooters Choice grease is good on slide rails again because it won’t shed when a slide is cycling, and bolt lugs for the same reason. Chip McCormick Trigger Job grease on a hammer/sear notch will help smooth and reduce trigger pull. In one of my pistols, it reduces the pull weight by 10 ounces and eliminates the sear creep. But still these lubricants needs to be cleaned off periodically along with any carbon build up and re-lubricated. A well and properly lubricated firearm is a happy firearm.
@CrowBarActual3 жыл бұрын
I jumped in at the deep end when I built my first rifle (milled the receiver, installed barrel, etc {didn't just put an upper on}) and to top that off, it was a .308 build. For the first ~300 rounds through it, I had to lube the snot out of it to the point there would be an oil puddle on the bench after shooting a few rounds just get the rifle to cycle reliably. There was never any signs of burrs or abnormal wear and I had an adjustable gas block to ensure I wasn't over/under gassing it. Anyways, after that ~300 or so rounds and what seems liked buckets of lube, the rifle now runs flawlessly with what most would consider a typical amount of lube.
@traceywalker28873 жыл бұрын
9.5 out of ten both for the content and synchronized coffee sip.
@n8sot3 жыл бұрын
Not a big fan of the Rand or the newer CLP. They both work great if you use the firearm frequently. But if you let them sit for a long period.....the rand tuns to a super thick and sticky mess. The newer CLP gets crusty after setting. Old school Rem oil hasnt failed me yet.
@larryw54293 жыл бұрын
T-6 shell rotella 5w40 diesel oil works in all my guns winter and summer and it also works in my classic cars!
@TommyboyGTP3 жыл бұрын
Slip 2000 EWL, lube and wipe off excess. I've yet to have a lubrication malfunction in any firearm using their products.
@TylerLL21123 жыл бұрын
I use EWL 30. Amazing stuff.
@Tadicuslegion783 жыл бұрын
I want to know Caleb's secret to such perfect hair
@dbelex3 жыл бұрын
WD 40
@paolodeep84593 жыл бұрын
Just the right amount of lubrication.
@badmoon75493 жыл бұрын
The right amount of lube makes heads thrust.
@davidharris90772 жыл бұрын
I have used oil on every gun I have ever owned and will continue to do so. I have NEVER had a problem in 50 years. I use very little grease but many people would say that I over lubricate my firearms. I don't care what others say, I will continue to oil my firearms. I keep my vehicles, boats, guns, and machinery ( and even my Wife ) well lubricated and clean and they ALL have lasted me a lifetime.
@wacojones80623 жыл бұрын
Nothing quite like a foursome of well lubed Browning M2 HB with 10,000 rounds to use up before the range closes. Loved my time teaching Cav Scouts as a reservist.
@elias87203 жыл бұрын
Hey Guys! Thank you for the video! I lucricate my AR rather on the "wet" side. Any too much lube is going to be shaken off after the first few shots anyway. But as you said: The DI system relays on good lubrication. In this subject i have a mith for you: It is i comon fact that you should store your rifle with a small layer of oil in the barral to prevent corrosion. I have heard, that if you are hunter, and the first shot you take counts, you need to de-lube the barrel before shooting, because the oil in the barrel will interact with your accuracy in a bad way. Please cover that :) BR from Austria from the beautiful Alps :) (PS: English is not my first language, but i hope you got the point)
@tightwad2 жыл бұрын
Your English is better than most Americans
@reedr16593 жыл бұрын
I was taught "AR-15s like to run wet." It was stated that if it's not spitting a little oil at first, it's not wet enough. I've seen few problems with actual lubrication though. The malfunctions I've seen with these rifles have usually been either a bad round or some other mechanical defect. At any rate, it never hurts to bring an extra rifle or spare parts. Doing classes, there's usually going to be at least one person whose rifle goes down during the day.
@dontneedtoknow58363 жыл бұрын
I know after almost 3k rounds and two squirts of CLP each day at the range. An m16a2 does not malfunction because of this.
@diegomontoya30653 жыл бұрын
Great content.
@danoneill28463 жыл бұрын
When all else fails READ THE DIRECTIONS !!!
@looseballs19663 жыл бұрын
DIRECTIONS?,,,,, WE DON"T NEED NO STINKING DIECTIONS!!!!!!,,,,LOL.
@richardturk71623 жыл бұрын
TW 25 B I have been using for decades and all it takes is a very small amount. Used to mix TW25B with alcohol and spray it on feed pawls of belt fed weapons or weapons that might see time underwater. A wonderful product but like any lube never over lube.
@stevenrichards36992 жыл бұрын
You need a Hi Point sticker on the door of that gun safe !
@scottlawrence18263 жыл бұрын
Thank you guys! I appreciate the content! Now I know the term “head thrust” 😎
@davisbwaddell3 жыл бұрын
That "AR-15" could use a retro brn-180 buttstock
@CalebSavant3 жыл бұрын
I agree.... every dang time you comment about it... I agree totally lol
@rick-kx7gy3 жыл бұрын
Remarkable restraint in not reminding any Elmer Fudds out there to not pack lube down your guns bore . Or allow dawn wabbits to shove carrots down them either .
@elmerfudd76743 жыл бұрын
ssssshhhhhh be vewy vewy quiet
@DinoNucci3 жыл бұрын
Correct information
@anthonyrichard4613 жыл бұрын
Remember at the range when in the Army, sprayed a tad or too much of CLP on bolt group right before qualifications. First shot got sprayed in dominant eye with high pressurize CLP. Blurred vision for remainder of shooting qualification. Didn't do my best shooting that day, just saying. Still wish I could see much less hit a target at 300 yards with iron sights. Y'all have a good day now.
@davidcoleman62113 жыл бұрын
Thanks for the info.
@Jeff_Seely2 жыл бұрын
I am a solid opponent of heavy lubing. Grease has no use in firearms, only light oil such as plain old mineral oil is needed and if you can see drops or running oil trailing, then it is too much. Just put a drop in friction areas and wipe it off. If oil finds its way into the chamber it can defeat the process of brass forming to seal with the chamber, can wreck your gun, and can even hurt you. I have seen people at the range spraying a fine mist out of their AR-15s. That's ridiculous and quite honestly it's dangerous.. I lube my firearms like this, cycle thousands of rounds, and have no issues with wear on my guns whatsoever. And I like it I guess with the silicone flannel rag to protect the exterior.
@GunsmithBeard3 жыл бұрын
3:16 That's what she said! OMG hahahahaha
@kauaigold2 жыл бұрын
Have 100% had an AR malfunction because of excessive oil that leaked into the firing pin. Gun was clean (pristine) so the issue wasn’t fouling, the oil caused the firing pin to not strike the primer hard enough. Took racking and light striking 4 rounds before it fired normally.
@steakwilliams44483 жыл бұрын
This segment wasn’t as “cut and dry” as I expected. Lots of good points. But for those of us that have been shooting for years but are new to ARs, one piece of advice we hear is to “run it wet”. I haven’t had a chance to shoot my new AR yet, and I’m certain I don’t have mine *too* wet but I was thinking maybe it could be wetter. I definitely don’t pack grease in the firing pin/bolt head, but where is the fine line? Normally I’d just go out and shoot to figure it out but with ammo costing as much as it does I’d rather not use all my ammo trouble shooting my new tool. Any pointers, anyone?
@CalebSavant3 жыл бұрын
Check out our videos on proper lubrication, that should take care of any questions in that regard.
@shawnr7713 жыл бұрын
I used to wipe M16s with an lightly oiled rag. Just enough to see a sheen. They run just fine. If the rifle has too much hot oil coming out of the ejection port can hit you in the face. Then you will know you got too much.
@jimd80083 жыл бұрын
thank you again
@sigsauer5053 жыл бұрын
First time iv heard not to lube the spot behind the gas rings
@rudygeorgiamulesandcountry15942 жыл бұрын
I've seen a Remington Model 700 seize up in -10F temperatures simply because the owner wiped too heavy of a film of oil on the bolt.
@xs650abear63 жыл бұрын
Frog lube gummed up my AR15 causing light primer strikes. Removed the Frog lube and re-lubed with Slip 2000, problem solved.
@glockparaastra3 жыл бұрын
There is always time for lubrication!
@AndyCigars3 жыл бұрын
Evolution! Great flick! 👍🏻
@brianbard9016 Жыл бұрын
Sometimes overlubricating gets my bolt jammed in the lugs.
@BigBarnV13 жыл бұрын
I use a tooth brush put some oil on it and it seems to brush on the right amount.
@EpilepticOrchestra3 жыл бұрын
Ordered two pistol mags and went to the outdoor range. It was windy and dirty and dust were getting everywhere. I had a couple of miss feeds and thought my gun was malfunctioning. When I went home and cleaned everything I saw that the two new mags had a lot of lube and seized up with all the dirt.
@jerryoakes33643 жыл бұрын
My wife walked in while you were talking about over lubrication and headed for Rust she thinks I’m watching porn.🤫
@onemarktwoyou3 жыл бұрын
Dirty and dry or dirty and wet? I hear it both ways. Lightly oil or heavily oiled doesn't seem to matter until it gets cold, then it is which lube more than quantity. I lightly oil those areas that contact each other. If you lightly oil you may want to add a little oil after you run 200 rounds through. But after cleaning no matter what I lightly oil for storage reasons.
@YellowHammer263 жыл бұрын
I learned my lesson about 25 years ago when my firing pin was gumed up do to over lubrication and I had a delayed shot while shooting at a deer with my Remington model 700.
@ViktoriousDead3 жыл бұрын
Like a hang fire?
@YellowHammer263 жыл бұрын
@@ViktoriousDead I pulled the trigger, nothing happened. Raised my head off the stock and the rifle went off. Took it to a gunsmith and he told me my firing pin had gummed up do to having to much oil. That was in 1995 . He cleaned it and I've never had a problem since.
@theroller56732 жыл бұрын
Rather than taking the gun all apart to lubricate it, drill and tap for grease zerk installation. A few pumps from a grease gun and you're good to go.
@jasonlopez48552 жыл бұрын
My LR- doesn't work for me if is not wet bolt how come is only got's 300rounds though it. Is that a problem.
@ricksilvis53693 жыл бұрын
Made the mistake one time of using paper shredder lubricant in the bolt of a 20 guage shotgun. It hummed up the bolt so bad the firing pin stuck. Had to completely stripe the pump completely and clean with carburetor cleaner. Never use sherrder machine oil in your fire arm.
@ETHRON13 жыл бұрын
Anyone else catch the Mil-comm reference... I use it on everything.
@WordSaladSpeachWriter2 жыл бұрын
Caleb can lubricate a small army of AR's with the "lube" in his hair.
@tryagain762 жыл бұрын
M16A1 was so loaded with CLP it would blast a mist cloud of lub with the first shot. 9-1/2 years and never a single failure. Nothing like a triangle handguard rifle.
@sacklunch73692 жыл бұрын
I used to clean my M16 in the sink at basic training and then lube the shit out of it and it was the only one that never malfunctioned but that was a different situation with an old worn out rifle
@daveandersonangry Жыл бұрын
dear sirs after storing a lubricated rifle for some time should you run a dry patch through the barrell before using it again
@dannie31173 жыл бұрын
Good video. Have to learn more about head thrust
@CubaLou1 Жыл бұрын
My thing is the point they brought up at the end where the excess sprays everywhere. That’s what I consider over lubing. That’s what I want to avoid. So no lube on the bolt tail?
@wowmageturtle153 жыл бұрын
i was running a 22lr conversion bolt in my ar. after about maybe (300 prior range trip no cleaning) then 100-150 rounds it started short stroking and stove piping every 5-10 rounds. squirted some lube into the bolt, wiped off excess ran great for another 100 before we left the range. moral of the story. lube your bolt even if its dirty ammo (maybe even ESPECIALLY if its dirty ammo)
@JoeArn13 жыл бұрын
If you use too much lube and tons of crap gets in there... TOSS IN MORE LUBE hahahaha
@algoneby3 жыл бұрын
My philosophy over lube by a little when gun is new, check for wear spots after shooting, then lube lightly for the rest of the life of the gun, or new parts. My AR rifles run fine a little on the dry side, although, I don't shoot tons of rounds. I do the same thing with most other guns. New, lube up, shoot, inspect, then clean, and lube lightly. Kind of a breaking in process.
@ChristianConstitutionalist31923 жыл бұрын
I Always Use More Lubrication Than Recommend For ALL Of My Guns And I've NEVER Had A Malfunction.
@michaels.98943 жыл бұрын
if you've never had a malf then you aren't shooting enough
@ChristianConstitutionalist31923 жыл бұрын
If Someone Has A Malfunction Normally It's Because They Don't Take Care Of Their Guns, Or Their Gun Is Just A POS (Like The Sccy CPX-2).
@squidy40822 жыл бұрын
@@michaels.9894 you can shoot a BCM dry out of the box and shoot 7k rounds without an malfunction
@michaels.98942 жыл бұрын
@@squidy4082 Ammunition related malfunctions are a thing, regardless of how good your rifle is. Train for it. If someone says they’ve never encountered one, it is simply because they haven’t shot enough.
@bananaman-qj4nu3 жыл бұрын
I'd also like to add that if you use too much lube or the wrong kind it can start squirting out and making a mess while firing
@lesschattermoresplatter57692 жыл бұрын
Don’t know about an AR but I had an sks that if you oiled the firing pin it would NOT fire. I also had a mini 14 that in a pinch greased the bolt with the only thing I had available… red chain lube. That was in June and it worked fine but long about January I tried to shoot it and after it failed to eject the empty case I physically pulled the bolt back and it looked like someone blew stringy red snot all over it. . 🤣
@moemarchetti93373 жыл бұрын
I would say yes. Now I'll watch the video.
@disturbedmaynard38733 жыл бұрын
The problem with KZbin is that too many people have done videos on lubricating your AR-15, and the amount ranges from dripping wet, to borderline dry. In the Corps, we used CLP to clean it and LSA to lube it, and looking at it when finished, they looked wet, but far from dripping lube. I have tried many lubes on mine, and find that minimal lube works just fine. Maybe do a video on the proper lubrication of the AR-15 platform.
@jonduncansakurawallknifegarden2 жыл бұрын
There isn’t one video where i don’t learn at least one two things I didn’t expect to learn from the video. There is always so much extra, and vital info that is shared here. This is one of my favorite KZbin gun channels over time. Great content as always.
@JoeyIngles3 жыл бұрын
I’m sorry. I know it’s sophomoric, but I giggled @1:20...over lubing causes more head thrust.
@advmotorrad Жыл бұрын
some people use grease in handguns some says dont use only light oil .. what is correct?
@KPad878 ай бұрын
Anybody know what that rifle Holder is called ?
@ReelSeriousAnglers2 жыл бұрын
What's the name of the device used to prop up the AR-15 Rifle?
@thebrucechannel80613 жыл бұрын
Always wear protection
@dandans67793 жыл бұрын
Overlubrication can cause hydraulic overpressure and excessive carbon residue especially in striker fired handguns (in the striker channel of Glock pistols for example). Overlubrication CAN lead to issues.
@griff69853 жыл бұрын
It sounds like the potential problems that they describe are not related to over lubrication so much as lubricating areas of the gun which should not be lubricated, such as the chamber and the firing pin channel.