SOLVED! Dodge No Bus Code

[@arnoldschwarzenegger7111]

I wish all videos were just like yours. Short and sweet. Nice work

[@YourHighne555]

Swear that's why I clicked it

[@Deesteelersfan79]

On my 99 Durango I had no bus. Mine ended up being a faulty pcm I replaced it and it was good after.

[@willdabeast144]

What website you order from?? And what was your symptoms

[@Deesteelersfan79]

@@willdabeast144 it was so long ago I can’t remember the website. It was some mopar dealer out of Florida. The symptoms were as follows. I would be driving and it would just shut off I would lose all dash lights, just dead in the water. Down in the odometer screen it would say no bus so I looked it up online and everyone said battery cable’s and look for shorts. I did everything seemed fine then I read about the pcm I took a gamble not knowing if that’s what my issue was for sure. I ordered it I think it was like 400$. Was also in 2004, PCMs were harder to come by. You would had to go thru the dealership most times. It cost upwards of 1500 @dealership anyway. I gave my vin they flashed it in and when I got it plug and play. I think I had to turn the key to start like 10 times. Then it fired right up. I don’t remember the company name. I recently had similar issues on a 2012 Chevy captiva. I ordered it for 185$ through www.mintt.com they have great prices and they do the same as the other guys. With flashing your vin into the module. Good luck I would say check your cables

[@timstidham9223]

Did your fuel pump engage before replacing ecm? I have the new bus code and noticed my pump wasn’t engaging that replaced the fuel pump. It started a couple times but would die and now still doesn’t engage I changed the crank sensor

[@chaposnalgas7808]

@@timstidham9223did u ever fix it because I changed 2 computers and both are doing the same thing got them refurbished from Oreilys

[@artisanwest9730]

I have a 2002 Chrysler 300M and it just started giving an intermittent "no bus" with the gauges shutting off. I will look for grounds and clean to see if that fixes it. Thanks for the idea.

[@AliAbady93]

Tell me if your problem solved with cleaning only???

[@artisanwest9730]

@@AliAbady93 The engine compartment is rather full so hard to see any grounds. I re-seated all the connections on the PCU but the problem has come back again. Very intermittent. Car will start and run ok but gauges are affected.

[@Deesteelersfan79]

@@artisanwest9730 I had the same on my 99 Durango it ended up needing a new pcm

[@artisanwest9730]

Thanks for the feedback. I'll probably have to take it in to the dealer. However, body control modules may no longer be available. @@Deesteelersfan79

[@AliAbady93]

I tried to clean all grounds but the problem still the same, engine work normally but intermittent no bus message and all gauges fall.

[@ChinoGarcia-gi7me]

I have a 2001dodge ram 1500 motor 5.2 its giving a code 950 no bus ?

[@StevenMiller-yw2ho]

Will the truck just quit running as your driving do you know of it acts like it's out of gas but it's not but that code comes up

[@maddhatter3564]

same here. ran perfect then died about 1/2 mile after a fill up at a new station. (thought it was bad gas at first.)

[@essgettitblonyt3616]

@@maddhatter3564im having the same problem here , do you know what it might be?

[@dougcruickshank4340]

200l Ram 3500 diesel after starting push brakes then no bus code in odometer

[@pnwvibe3123]

Look for issues in the can bus line anything that is part of the CAN system can cause that

[@maddhatter3564]

thanks but my truck ran fine for 3 weeks (i just bought it) and suddenly the no bus came up . only codes were central control module (a rom issue.)

[@davidqueen4719]

My 99 durango will still start and run. Gauges die and lights in dash light up. Keeps coming out of overdrive.

[@LuisRamirez-gc7rd]

Good video with some good humor .

[@bobbrien]

thank you thank you thank you amazing fixed ours as well big thumbs up Pal

[@YourHighne555]

Right on love

[@bobsoft]

Symptom: Engine will not start. Gauges are inoperative. NO BUS message displayed on odometer. Problem 1 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Crankshaft Position (CKP) Sensor. Problem 2 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Camshaft Position (CMP) Sensor Problem 3 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Manifold Absolute Pressure (MAP) Sensor Problem 4 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Throttle Position Sensor (TPS). Problem 5 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted wire.. Problem 6 of 6: The 5v power supply from the Powertrain Control Module (PCM) is shorted due to a shorted Governor Pressure Sensor. Also check your grounds on the heads/firewall and fenders. The PCM may have broken solder joints due to heating and cooling of the main PCB. Not to blame Dodge/Chrysler, this is a pretty common problem with many electronic devices. Any electronics that gets hot then cools is going to flex the main PCB and break the non lead solder that is used in electronics. If you want to take apart and repair the PCM check "Keenan Laws" KZbin videos on repairing the Dodge PCM

[@stevendepascale8364]

This isn’t a fix this is an error on your parts when, people are going through hell with this problem and most common suggestions is crank sensor a short dirty bad grounds not forgetting to hook them up !

[@MikeTumbas]

Jj😊

[@motorhed__4333]

Gayest watch ever bro

[@frozensunset]

Just touching base here This wasn't the actual issue but due to your video I was able to go out there and actually troubleshoot and I found a short in my wiring harness right underneath my same spot that you were touching in the video though oddly either way Mopar power