Started watching without much expectations ... and actually learned a LOT. No wonder you have so many subs. Even on "trivial" subjects you extract gold for people that are no newbies. Very well done !!!!
@fontybits5 жыл бұрын
For many years, I worked for the Rawlplug Company. In the R & D Department within the factory, a 1 ton block of concrete was positioned in the middle of the floor. A small hole was then drilled in the exact centre of it and a red Rawlplug tapped tightly into the hole. An eye-hook was screwed fully down into the red Rawlplug. A portable crane was then used to lift and suspend the concrete block approximately 20 mm off the floor. Visitors were always shown this feat of strength of the Rawlplug.
@davidcooke30813 жыл бұрын
Rawlplug released a series of plastic plugs a few years ago called Rawlplug Uno. I have found them brilliant in concrete walls, you do have to make sure the hole and screw size are correct for the plug you are using. They do claim you can use them in plasterboard walls, never tried it but I'm curious if it works
@strandloper5 жыл бұрын
When drilling into a plaster wall the hammer action tends to cause more damage to the plaster so I like to leave the hammer action off while going through the softer plaster and only turn it on when I hit brick hard enough to need it. Sometimes you can go deep enough for the plug without needing it at all. It's also easier to stop the bit from drifting when starting the hole without the hammer action.
@victor-oq7dl5 жыл бұрын
Handy tip , thanks
@nowthenad32863 жыл бұрын
No way. You have changed my life! My solution to stop the bit drifting was to use a bullet tipped masonry bit. That really helped but your tip is awesome. Maybe I am thick for not working it out for myself, but hey ho! Thank you.
@MartiA19735 жыл бұрын
Never cease to amaze me; been using this sort of stuff for YEARS and yet Andy can still show stuff in a different light. Brilliantly done!
@RubberRivet5 жыл бұрын
Every day's a school day, I'm in my 60's, never thought of yellow in red or two in line. Thanks .
@gbjbasdw15 жыл бұрын
Likewise - I'm 65 and never thought of doing that !
@mariosavva9993 жыл бұрын
This video was very helpful considering my house is all concrete. In fact, all your videos are very good. Much appreciated 👍🏼
@alexwood5026 Жыл бұрын
Thank you for making this video. It answers so many queries where I’ve just guessed on past projects without really knowing what sizes for wall plugs, screws, drill bits & correct uses and hoped for the best. Subscribed 👍🏼
@strandloper5 жыл бұрын
The old school way I dealt with oversized holes when bigger plugs were not available was to force one or more match sticks into the hole alongside the plug. Worked well enough.
@smartfalcon81163 жыл бұрын
My dad didn that!
@steves14603 жыл бұрын
I’ve done that many times, but even better are the sticks that come with the diffusers that you use in bathroom smellies. They always put too many in there and they are long and very useful for said task.
@maranellomania_Photoshop3 жыл бұрын
If you are just starting out on your DIY journey then watch this video! Great explanation of correct use of both basic wall plugs and drill bits - thank you.
@markrowland53935 жыл бұрын
Great tips - thanks Andy. I've wrapped insulation tape round a plug on occasion when the hole is too big, but I think your plug in plug solution is better. And your two plugs back to back is brilliant. It's so simple and yet I never thought of it. I'm not going to forget that little gem! Thanks!
@ttsstt10005 жыл бұрын
One of the best bids you have done hands down
@kagelevelofficial3 жыл бұрын
Awesome thanks for this! Made a bit of a mess when installing floating shelves and felt not so good but this has been useful! Fingers crossed now, feeling positive
@adamanthony7465 Жыл бұрын
Totally useful...for a novice..a great watch on Sunday evening.
@nowthenad32863 жыл бұрын
I love this video. Most people wouldn't think to explain all these different scenarios in which difficulties can arise. I love the level of detail here. So, you can only carry so much stuff around on your jobs, especially when you always carry around the essential framed photo of His Royal Highness (RIP).
@johnshepherd56734 жыл бұрын
Been doing this stuff for many years, but learnt a lot ty 👍👍
@specialeffectsgraphicsdesi90664 жыл бұрын
LOLZZZZZZ! "I know in America you call them anchors or something WEIRD like that" 🤣😆👌🏻👍🏻! Great video. Learned a lot as a beginner.
@tubro007 Жыл бұрын
Excellent that you take the time to explain and display the basics. Very useful to learn for the beginners like me.
@btwfbtwf37532 жыл бұрын
Just to echo other people's comments. A great video, wasn't expecting much but learnt a lot. It was presented with clear imagery, good narration and explanations - I've subscribed
@Ssssshhhhh18855 жыл бұрын
Fantastic Andy Thank you. More tips for my library. Never thought of running them back to back. Will now. 👍👍👍👍
@GosforthHandyman5 жыл бұрын
No worries! 👍👊
@Paul-Graham5 жыл бұрын
Nice tip for the plug in plug! Would of never thought of that! Just came accross your channel recently as a reccomended channel, and already binged many of your videos! I also live in Ryton so from your neck of the woods!
@peckelhaze69345 жыл бұрын
Excellent video. These tips are something a lot of us discovered over years of experience. Extremely helpful.
@GosforthHandyman5 жыл бұрын
Cheers Sir! 👍👊
@derekjohn3574 жыл бұрын
Excellent video, so much useful information and clarification of plug & screw sizes. This has just solved several issues for this beginner DIYer. Thanks!
@ttsstt10005 жыл бұрын
One of the best vids you have done hands down
@mikeykeyes5 жыл бұрын
Mate so thrilled to see the Indian tri-colour in the company of the commonwealth! Good on you. Thumbs up just for that.
@MrBarrytommy5 жыл бұрын
Paired down wedges of timber was the way once, so quite convenient these wall plugs are really
@junior5553 жыл бұрын
Simple, but brilliant.....well done
@janetmorgan97823 жыл бұрын
I found this very useful, just what I needed at the start of a project where I need to make decisions on size of wall plug and the manner of fixing., strength being important.
@johnduerden5 жыл бұрын
I've been doing building work for almost 3 decades and I've never thought about putting a plug in plug, I would normally put splinters of wood if hitting a mortar line.
@johnthompson34625 жыл бұрын
great tips as usual. Love the two plug and the plug in plug
@frankslittleworkshop5 жыл бұрын
Nicely done once again 👍. The "Well done Andrew" statement should be reserved only for the following..... a yellow in a red inside a brown with two additional cocktail sticks...😂🤣😂. Keep up the awesome vids 👍.
@morganplatt67625 жыл бұрын
I always take the drill off hammer at first, check the hole and if needed, re-drill it back on hammer. Works every time especially for old brick or concrete block.
@ocdtechtalk4 жыл бұрын
Finally someone who understands HOW things work and just doesn't bang it in. So many trades by me just bang it in and then are surprised when it fails.
@asianhawk0694 жыл бұрын
Mate, you just saved me a huge amount of hassle. thank So Much! cheers
@harrycallaghan225 жыл бұрын
As always. Excellent tips and useful info. Nice one.
@nowthenad32863 жыл бұрын
Which is stronger: A wood screw in a wall plug OR a concrete screw straight into the masonry? How do you select between the two methods? Thanks
@ek68685 жыл бұрын
Excellent video tanx for the upload looking forward to dot and dab wall video can't usually get a good fixing on them walls👍
@idlersdream8265 жыл бұрын
Like you, I pretty much only use red plugs. I only ever buy the 'Rawlplug UNO Universal' plugs now, have used them for years and never had a problem, highly recommended.
@HantsLeo4 жыл бұрын
Thanks for sharing your knowledge. Interesting video and it was worth watching for the yellow inside a red let alone anything else. Stay safe.
@dmswamygowda53715 жыл бұрын
Very good massage thank you sr
@abyshepherd69444 жыл бұрын
I hate using these fixings but this video has given me confidence to recognise where I’m going wrong and do it right in the future. Thanks! Also love the excellent tips in the comments. 🙏 😊
@davecharlesworth81765 жыл бұрын
Great tips in this video. No more plug problems for me🇬🇧
@Andyfishing234 жыл бұрын
Great tips as ever Mr Gosforth! 👍 Keep them coming.
@Woodwork-Learner5 жыл бұрын
Always learn a lot from your videos, even simple stuff like how to get your drill bit back on track when you hit a little stone in concrete.
@GosforthHandyman5 жыл бұрын
Cheers! 👍👊
@Alexis_Mos2 жыл бұрын
I have a brick wall decoration of 1cm depth for the brick part. Can I drill with a 10mm on the brick? I want to hang a 65" TV
@christofix5 жыл бұрын
Those are some great tips. I learned a lot from this video. Thanks man!
@GosforthHandyman5 жыл бұрын
No worries! 👍👊
@benchippy80395 жыл бұрын
Always good to see tips that someone else has picked up. I’ve taken to putting copper wire into plugs that aren’t getting a fixing. Also, if the situation allows I sometimes bang a timber wedge into soft mortar joints and that will often be the best fixing in the whole piece
@GosforthHandyman5 жыл бұрын
Yup - defo, timber wedge is proper old school and still one of the best fixings in mortar lines. Totally agree. 👍👊
@JohnRMTurner Жыл бұрын
Great tip for SDS. I wish I'd watched this video before I drilled everything 6mm!
@neilfurby5555 жыл бұрын
Surprised to find this worthwhile viewing! The inner cores of 1.5 mm cable, and .... bamboo barbecue skewers are useful space fillers, as of course small wooden wedges. Thanks.
@MichaelEdmond5 жыл бұрын
My mate drilled a hole for a 8mm plug... And it was slack, He panicked. I grabbed an old pencil, snapped end off, and hammered it into the end of the plug.... It's proper solid!
@markhannan51674 жыл бұрын
I fit Kitchens and always use 7 mm brown plugs in a 6,5 mm hole with 2 inch 10s on wall units and it gives a solid fixing
@inquistive2 жыл бұрын
Brilliant Andy! If you are ever in Hertfordshire I need some carpentry work done please!
@ningis215 жыл бұрын
Hit a Mortar joint.....hole shot to bits....Filled it with Gripfill adhesive/mastic pushed in the plug....let it set...fixed bracket for item...been there 10 years...solid. Try it on one of your test Tuesdays..... No good if you're in a rush....But, next day fixing no issues. I suppose you could fix in a wooden dowell with good results too.
@aaronbell85273 жыл бұрын
I always use a smaller bit for the plugs like for my red plugs I use a 5.5 and for my brown 7mm plugs I use a 6.5 but very rarely use wall plugs now I love tork fixings
@huejanus55055 жыл бұрын
You can tap a small finishing nail (or two) between a plug and the concrete if the plug is loose in the hole. Quick and easy, and there's always a few nails kicking around.
@800Viffer5 жыл бұрын
Top tippage Agent Gosforth 👍
@Uwe_Ludolf4 жыл бұрын
Are this the standard S-series of Fischer? Like S5, S6 and S8? In the Netherlands I only find those in grey.
@HektorBandimar3 жыл бұрын
Really useful video, well explained and presented, good info.
@racker9999 Жыл бұрын
Thanks! I loved this video instruction. It was clear, simple, and covered the topic thoroughly. I just subscribed to your channel.
@Ahigh3lf4 жыл бұрын
Excellent video did not expect to learn as much i did to be honest, subscribed. Keep up the good work 🤙🏽
@raysmith19925 жыл бұрын
Some good tips in this video, I have some special old Thermalite plugs which have a wings on the sides and you have to hammer them in, probably not made anymore 😂
@rjamsbury15 жыл бұрын
What was that picture of Prince Philip doing in that shot of your plug collection? Made me laugh 😀
@GosforthHandyman5 жыл бұрын
😂👍 It's a reference to a certain type of screws I hate. Prezzie via Makers Central. 😀
@MohammedAli-vo8hq3 жыл бұрын
@@GosforthHandyman I thought what a nice tribute til I checked the date and comment lol
@replevideo60964 жыл бұрын
Here's a tip for people who just have a manual screwdriver, or a cheap electric one. The screw can get so tight that the screwdriver slips and damages the slot, making it very difficult to drive the screw in further. Put a drop of washing up liquid on the screw thread before driving it in, to act as a lubricant, and make the job easier. The liquid will dry up after a while and even make the grip more secure, and it won't rust the screw.
@k.hussain3605 жыл бұрын
Great tips Andy.
@GosforthHandyman5 жыл бұрын
Cheers Khurram! 👍👊
@MARTINA-gc3tq5 жыл бұрын
Inner cores of 1.5 mm cable pushed into oversized hole will provide a good emergency screw fixing.
@roverboy015 жыл бұрын
2:15.... You just stopped me from moaning about drill bit sizes. Lol. I always use a 5.5mm for the red wall plug.
@steveoutdoors59645 жыл бұрын
Yea me too. In fact the red plugs I have state 5.5mm bit. But I suppose it can vary depending on manufacturers.
@conorcrowley9895 жыл бұрын
The concrete screws used for windows with the t30 heads are great they are like a double thread
@Midas201011 ай бұрын
YES….. TWO PLUGS !! Awesome !
@alanwakefield24535 жыл бұрын
I always use Wicks Wet and Fix plaster pads for those powdery wall situations
@Col26655 жыл бұрын
fantastic vid great advice.
@carolloveskiwis4 жыл бұрын
Love your vids! I learn so much and save so much $ DIY. Thanks, keep 'em coming!
@StamosTee5 жыл бұрын
Great tips Andy, nicely presented! Good job mate ! 👍👍
@GosforthHandyman5 жыл бұрын
Cheers bud! 👍👊
@markbonham34775 жыл бұрын
Great tips, thanks
@sarwanamajid3 ай бұрын
Hi, Grate video. I need to install kitchen unit on wall and the screw which i'm using are 5mmx75mm and the wall plug are 8mmx40mm. Do I need to use two wall plug or i can just use 1 wall plug
@beyondutility4 жыл бұрын
Great tips - thanks for sharing.
@sj_harris4 жыл бұрын
Howay Andy Another great informative vid. Quick question, what happens if you put a long screw through a single short plug? Presume the holding strength is diminished? Nice tip for doubling up the plugs by the way, shall try that :)
@honolulu14765 жыл бұрын
Brilliant.
@allanhmelnitski9785 жыл бұрын
Wood is good for plugging, and pieces of cable into oversized hole works also
@smartfalcon81163 жыл бұрын
Very good video! Thank you :)
@zakariabelila67614 жыл бұрын
thanks for the tips it really helped me
@frankiesalmon75455 жыл бұрын
Cheers Andy good video again
@owenbutcher19545 жыл бұрын
Thanks for the advice
@corneydeb5 жыл бұрын
As always very informative thank's.
@blade7974 жыл бұрын
I bought ceiling-point anchors... or pad eye plates. The kit came with orange plugs. These anchors are going in studs, are the plugs still necessary? The point-anchors will suspend at least 2-300lbs. I thought plugs were more for when you cant find a stud... or are they still needed in a stud if you are using them for heavy duty purposes? thanks!
@literate-aside2 жыл бұрын
Love the videos, just discovered the channel. I enjoy watching back to basics style videos as you can often pick up excellent little tips. By the way, I know over time on sites it's drifted away from this, but technically they're actually rawlplugs
@talamantezfamily32864 жыл бұрын
Thanks. I'm going to try this.
@acoustic243 жыл бұрын
Thank yo u so much for your time, really usefule stuff.
@cliffroe58673 жыл бұрын
i have fitted a bath screen to a plasterboard ceramic tiled wall, i chose 6mm Fischer duopower plugs, my question is... if i need to remove my bath screen when decorating will the plugs still be ok for screwing the screen back onto the wall again?
@johnh50085 жыл бұрын
What I like to do is drill a pilot hole, put a short length of bare copper wire (12 or 14 ga) in the hole and then drive the screw in. The copper will smash around the steel threads of the screw, acting like a makeshift helical insert. Holds really well. Not sure where I learned this but i like it in concrete walls.
@simdog6355 жыл бұрын
Good tips Andy thanks. Cant wait for the plasterboard /Dot & Dab series as i always struggle finding a Good Plug. PS I think a pink bracelet would be more fetching ;-)
@janthomson76972 жыл бұрын
The rawl plugs which come with item purchased are usually substandard
@petercurtis92975 жыл бұрын
People don't tell you this stuff. Thanks. Bought a trailer tent today. Got my handy man tape out to measure up the trailer. The salesman was impressed, so I told him where he could get one.
@Roozbeh72 Жыл бұрын
Great video. Any tips for preventing drill bit tip slipping from engineered bricks? They're a nightmare to drill into, and I had to buy a mains SDS hammer drill, on top of an 18v Combi hammer drill (which couldn't do the job!)
@iiparachuteregiment88003 жыл бұрын
You are great, iv learnt a lot
@PetePuebla3 жыл бұрын
I never knew there were color-coded. That's news to me but it's good to know.
@lilybooth4661 Жыл бұрын
What do you do if you can only get 3/4 inch into your exterior wall? So something for a good holding material but very shallow?
@annosuke Жыл бұрын
Really helpful thank you
@DrRasputin20122 жыл бұрын
08:40 - I've also used cocktail sticks to help pad out a hole.
@HepauDK3 жыл бұрын
The walls in my house are made from Leca, so the hammer action isn't needed at all. It creates other challenges though, so I usually use a large pick to make a hole that will keep the bit centered. The reason why I use my rotary hammer anyway (Bosch GBH 18V-20), is because I have a GDE 16 Plus dust guard for it, that I simply hook up to my GAS 18V-10L vacuum. That way all the dust is removed while drilling, and I don't even have to clear the floor under the spot. :) Looks like I will have to get me a set of 0.5mm undersized bits though...
@Cryptolorian2 жыл бұрын
I have 5mm screws 60mm in length, do I need the red plugs or the brown ones? Thanks
@cjhification4 жыл бұрын
Bring in the big daddy! Gotta love a Rawlbolt (other competitor wallbolts are available).