SOTF: 72cc Chainsaw under $200

[@naturundhund]

Nice Chainsaw...greetings from Germany Peter Husqvarna-Pit 😊

[@sawsonthefarm]

Thanks Peter, glad to have you!

[@TomRiddle-ww5on]

Nice to receive a funnel and fuel/oil jug with the saw. I want one!! Just to cut firewood and play with.

[@sawsonthefarm]

So far it's not too bad! I'm having a blast messin around with it!

[@courtneykensington8190]

Those clone saws are good…. they’re perfect if you want to tinker and mess with them and it doesn’t cost a whole bunch of money if you wanna make a Frankensaw. I have a farmer tech 395 and I’ve had to replace quite a few parts on it, but generally the saw runs fine. I like how they misspell Husqvarna though that made me laugh… cool video.

[@sawsonthefarm]

I agree! Perfect to mess around with! I always wanted an erector set as a kid! I think I paid less for this saw! This is really the draw for me, tons of fun on the cheap! If I break my toy I can just buy another!😁 thanks for watching!!!🤙🏻

[@tylercearley7778]

I own the same saw but put a skip tooth chain and changed the bar and but using it since last Valentine's day and I run to snot out of it and it ain't failed me yet I cut timber and firewood on a regular and no complaints

[@naturundhund]

I You're welcome, you have a nice channel... It's fun to watch  

[@sawsonthefarm]

Cool! Thanks

[@matthewknight5641]

I have alot of the clone saws. Some ported now and all different sizes and types. Most are good for the money and the ported ones are fun.

[@sawsonthefarm]

Very cool! Thanks for watching!

[@matthewknight5641]

Run 32.1 in all clone saws. The tolerances arent as close from what ive been told and 32.1 will give more of an oil cushion on all the bearing surfaces. Good luck and have fun man

[@sawsonthefarm]

So far so good! I'll update as it unfolds!

[@johnwright1464]

I run 50:1

[@matthewknight5641]

@@johnwright1464 I ran 50.1 for awhile in a clone 660 but it was wearing on the piston on the intake side something terrible. I replaced the piston and started running 40.1 premix and it didn't seem to wear as bad then the guy that I got some ported saws from recommended the 32.1 and I've been running it ever since and really like it. I guess we all do it differently but 32.1 seems to work best for me

[@diggindiggenit6540]

Yeah pretty cool under 200, sounds good, post an update down the road on the feel and cutting performance. I did pretty much the same thing went with the g660 pro, and a clone husky 395 both are new in the box have yet to open the boxes to check them out. have fun

[@sawsonthefarm]

I plan on it! Thanks!

[@justinbuthod8596]

Did it come with a 3/8 .050 chain? I just ordered the 365 version of that saw and i want to get a better bar and a couple of chains ordered. Thanks

[@sawsonthefarm]

I believe it is 3/8 .058 gage.

[@justinbuthod8596]

@sawsonthefarm my saw was delivered today. It came with .063 chain and bar.

[@sawsonthefarm]

Wow! Ok!

[@napalmjack]

I just got a 441 Sthil for about $180 on market place. Only needs the side cover for the pull rope side.

[@sawsonthefarm]

Wow! That's a sweet deal right there!

[@Reubentice76GTR]

We're paying too much for saws here in the US. My new 500i cost over $1600.

[@sawsonthefarm]

There's no way I could justify that price unless that was my livelihood!

[@davediesel90]

@@Reubentice76GTR they cost the equivalent euro amount in Ireland

[@cletusschaub4398]

@@Reubentice76GTR In my experience I am not impressed with that saw you would have been better off with something else

[@brandonf1226]

Awesome I got one of these exact brand and other than throttle being harder at full throttle it's great so far 3 tanks.....very rich out of box and ba is worn from the wrong size chain.....have to clearance the ribber chip deflector for a .060 bar but after that it's screamin....I widened exhaust and deleted base gasket next is the muffler mod

[@tomcrockettsr]

I like how they took the name Husqvarna and transposed the letters!

[@sawsonthefarm]

Yeah that's not right! It could fool you lookin quick!

[@Condor1970]

I got the Neotec version of an MS381 for $218 on sale. A lot of guys say to run a couple tanks 25:1 with these cheaper Chinese engines to break them in. Then run 40:1 or 50:1 like normal after that. Also, run a bit rich then adjust the carb eventually once the diaphragms break in.

[@sawsonthefarm]

How is it? Any issues? I've heard the Neotec's are not that good. I know they are all hit or miss but, we can still get lucky right!

[@Condor1970]

@sawsonthefarm Honestly, I've only used it a couple of times and haven't even gotten fully broken in yet. Still running 25:1 on the 3rd tank. I will probably switch to 43:1 next time I use it, and lean out the carb a little. All that said, it seems to run quite well, and is very strong. I can see it being a real work horse once fully broken in and tuned. The problem is, I use my old Stihl 025 for just about everything, and only got this Neotec because I rarely need anything over 20 inches just for general firewood and storm cleanup. And because I only need it a couple of times a year, I just couldn't justify spending $1,400 for a new MS460. So far, I think it was a good buy.

[@sawsonthefarm]

Good deal! They have their spot!

[@rodneymiddleton9624]

That's crazy! Thanks!

[@Joe_Blo]

The 365 was $169 on a black Friday sale. I am surprised Hsyqvrnna didn't knock off the 50cc xp versions too, like the 346xp & 357xp. -Your clutch bearing needs grease.

[@sawsonthefarm]

That would be cool if they did!

[@alltherpm]

I bought a farmsak from Amazon $270 delivered with bar,,, i just ported & polished exhuast, 268 piston and muff mod and its strongest saw ive ran other then my dolmar 7900

[@sawsonthefarm]

That's cool! Love your handle! @alltherpm that's awesome!

[@michaelpersson68]

Yes looks ok but how much spearparts on this

[@sawsonthefarm]

It's a clone of a Husqvarna 372 so all the parts are available aftermarket and interchangeable.

[@Memry-Man]

I love mine

[@ruggedtimber1743]

For 200$ I don’t think you can go wrong. What size bar do you plan on running on it? Cute little gas and oil can they send in the box.

[@sawsonthefarm]

It came with a24" bar. So far I gotta say I'm a little impressed! lol! Yeah how bout that can! lol!

[@cletusschaub4398]

Ha ha I bought a good 700 Mac with A 30 inch bar 85 00 dollars runs real well lol

[@sawsonthefarm]

That's a steal!

[@metalandwood4u]

Its gonna run fine. Order an unlimited ignition coil and a momentary switch from husqvarna. That will be the only thing you must have......see if your carb gives you full power.

[@wg4405]

Might be fun and exciting if you ever need a carb kit for it ??? I run 32:1 in everything I own and I use Lawn Boy 2 stroke oil , my local Mom and Pop lawnmower shop that is a Stihl dealer sells the oil and and they use it in there repairs .

[@sawsonthefarm]

I don't think it will be bad, it's a strait up knock off of a walbro!

[@kennethhathaway3823]

32:1 is not a good idea your saw will get to hot I promise you but figure it out for yourself if you don't think it's a problem

[@wg4405]

@kennethhathaway3823 Really well I tell the Owners of the Lawn Mower shop that been in business since the 80ties along with their mechanics that have been doing it for years . In fact they break in all the Pro Stihl they sell with 32:1 before they give them to the customer and they tell the customer to run 32:1 . Been running my saws for quite a few years now and ain't burned up nothing or blowed up nothing . Kinda strange most all my saws that are antique say run 40:1 or 32:1 . I even have a few that say run 16:1 .

[@davediesel90]

​​@@wg4405you know you won't tell them 😂 but the man has a point. The fuel provides a lot of the cooling in a two stroke and it's been proven 50/1 it s sufficient with modern two stroke oil, 16/1 32/1 etc was when ordinary 30 weight oil was used.

[@wg4405]

​@@davediesel90 " You know you won't tell them " ----- tell who what . If you think I'm going to go tell a Lawnmower shop that's been in business since 1980 how to run their business and get into a p!$$ - ing match about 2 stroke mixture like some of y'all do here on the interweb it won't be happenen , but you can call Lawnboy and tell them to stop printing on the back of their bottles of 2 stroke mix how much gas to mix to make 16:1 , 32:1 , 40:1 and tell them just to put 50:1 on their bottles . Lawnboy 2 mix oil is not synthetic . I don't and ain't gonna run any synthetic and it's all over the interscreen that the Gray bottle Stihl synthetic two-stroke is causing more harm than good and I'll keep running 32:1 also in my Lawnboy commercial self propelled bagger push mower that was the last 2 stroke version made like it says to do on the top of the gas cap .

[@alltherpm]

I went to pop spark plug wire off plug and ripped the boot in half it was so cheap rubber, so bought a husky ignition & carb

[@sawsonthefarm]

The quality is definitely not there with some of these components!

[@alltherpm]

I also noticed whatever fuel they run at factory is one dirty fuel & oil, for the second they run it i couldn't believe the ash, gas in carb was black!!! Lol

[@brownwrench]

They chose a good model to knock off

[@sawsonthefarm]

Yes they did!

[@ashleylaw]

It was pre-tuned to 50/1. Running 40/1 will run lean out and lose power in the cut. Or worse. Must use top grade fully synthetic oil. Running without airfilter messes up carb settings to. Believe it or not the factory tunes and tests on these parameters.

[@sawsonthefarm]

Actually you have the mixture theory backwards 50 parts of fuel to 1 part of oil is a leaner mixture than 40 parts of fuel to 1 part oil. I use the 40:1 for more oil protection and yes I always use a name brand synthetic oil. As for running without an air filter I strictly do this on the bench. Once the saw is complete and I'm ready to start cutting is when I tune the saw. I tune a saw every time I use it for the wood I'm in as well as the air temp and density. These carbureted small engines require constant tuning to keep them at peak performance without damage. Thanks for the comment and your thoughts, this is why we do this stuff to learn and share! 👍🏻

[@ashleylaw]

@@sawsonthefarm No. That is not correct. If you don't believe me ask your local Husky dealer. Yes you are running a thicker mix but everything on that saw from factory was tuned to 1/50. Running 1/40 means you have to retune it. Or it will pull more air to compensate and then run lean and you will lose power at best. A tip don't run Stihl ultra unless you going to run it hot all day. Otherwise it will carbon up fast. Oh and at 40/1 It will run hotter so more stress and wear results over time. But at only 200$ no Biggie looks a bargain.

[@sawsonthefarm]

@ I hear your theory and no disrespect. I've always run every saw I own old and new all makes and models like this. I have never had an issue. I do appreciate your take on this, respectfully I'm goin to stick with what works for me. I did hear that about the Stihl oil, that it creates a ton of carbon if there is a lot of idling. I've heard that the Echo red armor is really good! Thanks for your comments!

[@alltherpm]

​​@@ashleylawno your wrong how will it pull more air,,, it pulls same amount of air no matter the mix, more oil means better ring seal, also ive never had a tune off that bad from different ratio that I needed to retune,, silly,,,, I also say what consumes more air 600 cube 600hp big block or a 600hp 302 ford??

[@BentIronBins]

The less oil means more fuel in the charge but i prefer more oil for better ring seal and therefore more compression its all about tuning for the ratio and air density.

[@stevenfan1218]

Have bought several of those..they run for a while.break down .get fixed break down again..then get thrown in the building.

[@sawsonthefarm]

lol! Nice! I can't wait to run it hard.

[@naturundhund]

like your channel, subscription is out. Greetings from Germany.

[@sawsonthefarm]

Hello! And thank you!

[@williambray4134]

40:1 with a modern 2-cycle synthetic is fine.

[@sawsonthefarm]

Agreed! I run 40:1 in all my saws new and old, never have an issue! 👍🏻

[@biomechanique6874]

​@@sawsonthefarm Remind yourself that this is a Chinese machine that is made from parts less well finished than the big brands! Run on 25:1 at least for the first four or five tanks then go to 40:1 or you might have an overheat episode that will prompt a cylinder replacement, possibly to a 52mm big bore kit.

[@sawsonthefarm]

Hopefully not lol! Already ran a tank full of 40:1, if she blows she blows!

[@tomgraham8622]

Most two stroke engines benefit from running double the oil during break-in. OMC recommended in the 80's. The engines last longer. Just clean or change the plug(s) after break-in.

[@CreativeFishDesignsCharlotte]

im rebuilding mine a painr bt well worth it , redo everything in the topend

[@sawsonthefarm]

There you go!

[@w2tb36]

That little can isn't useless. Clip it on your belt. Filled. It can save you a long walk...

[@sawsonthefarm]

Good point! It's just so thin, I'd worry about a puncture! Those little fuel cans for enduro riding would be perfect to carry like that!

[@illnaturedsaws]

You did not buy a Hooskvarnuh hahaha I have a clone MS460 kit I built and I can’t even get the thing running.

[@sawsonthefarm]

No no I got the Hnsvarqua! lol! Yup I had to try it! That's too bad you can't get yours goin. I have that 440 clone that I've used a ton. I've had some issues too!

[@gunnutz2030]

Anybody else have 365 on their serial number plate and a 372 badge on the side. Because I do. Hopefully it's actually a 72

[@antonvouk4145]

I've heard some of these clones are 65cc with 48mm bore and labeled with the 372 stickers.

[@gunnutz2030]

​@@antonvouk4145well hopefully it's the other way around and they are all 65 cc to start out and then they put the 72 CC jug on them for the ones that they label 372. Has anybody pulled one apart and confirmed

[@gunnutz2030]

Because I actually got the 65 cc as well and it has identical markings to the one that I got the same day that has 372 stickers instead of the other one having the 365. The 365 has the tall filter on it already which is kind of weird and the tall filter housing

[@brandonf1226]

Some have the big dint carb some have another...

[@biomechanique6874]

It seems that China is starting to raise it's game.

[@sawsonthefarm]

We gotta see how it cuts next!

[@vikingfitz9088]

Chinese camera as well?

[@sawsonthefarm]

Well... it is an iPhone! lol!

[@scottfoster2487]

Seems the 372 is one of the most copied saws lol

[@sawsonthefarm]

That and the 660. I had to buy one just to see!

[@ArkansasChainsaw]

i have the 365 this same brand have 2 of the 372 same as this good saws need some wrenching but decent for the price i put a mini pipe my 365 it rips

[@theberkshiresmatreasurehun5337]

You should try a temu chain saw

[@biomechanique6874]

Those 52cc Chinese things? I got one cheap with burned up bar and chain then got given a busted one. I fixed them both up for under $40 in parts so $60 for 2 running saws. Done lots of work with them - they run pretty well took about 20 hours to run in and show surprising power now. I guess they take longer for the parts to bed in being cheap and less finessed. Wouldn't have gone and bought one new though, just these two happened to come my way a couple years back.

[@brownwrench]

Husasukah

[@deniscarter6613]

If a new Chainsaw is Cheap you pay for what you get and it's Called Trouble

[@sawsonthefarm]

It's all in good fun! If it blows up it's an excuse to big bore it!🤙🏻 thanks for watching!

[@oldcodger4371]

I've had a Stihl MS-270 for a long time and used it a lot. The other day, I got a new bar and chain for it, that was 80 bucks. New air filter $18. New Muffler $40. New Carb, $90. Them expensive chainsaws are also very expensive to repair and maintain. I have a Supmix and Pinkway chainsaw. Last year I sawed up 3-4 cords of Oak with that Supmix 20 inch with the greatest of ease. Never gave me a hint of trouble.

[@sawsonthefarm]

@@oldcodger4371 there is definitely a market for these types of saws. Expecting the type of reliability of a name brand saw would only cause disappointment. But we get these because they are cheap. We still can have good luck and tons of fun with them! Thanks for watching!

[@oldcodger4371]

@@sawsonthefarm The repairs and maintenance is almost identical as a chainsaw is very simple. It ain't rocket science. if three $100 chinese chainsaws last as long as a $650 stihl, you would come out ahead with the Chinese ones.

[@sawsonthefarm]

@@oldcodger4371 I would say if someone is not capable of repairing these saws themselves they should probably stick with a name brand with dealer support! These will definitely require attention to keep goin!