Clock Spring Replacement - Toyota / Lexus

[@Pratt-zp5mr]

Hey there. My neighbor diagnosed my wife's Camry issue with the horn back to a faulty clock spring. He sent me this video and, after watching a few times, I proceeded to replace the clock spring without issue on the first go round. Thanks for a well documented process around the procedure of changing this out. Thanks again!

[@speedkar99]

I'm glad it helped!

[@GeminiFight]

This is very informative without a lot of chatter , pausing , and obnoxious noises. Great editing . Thanks it helped a lot.

[@speedkar99]

+spencer spencer Thanks short and to the point is how it has to be

[@truthaboveagenda]

True. Very informative, well done.

[@jonny1943]

Yes it is perfect! so much shitty how to videos out there.

[@Rumeel12708]

Agree!!!!!! Great video.

[@dmellinger4887]

Agreed, it's a very well done video. One thing I wanted to see was how to install the ribbon cable into the round plastic housing. How many turns of the cable should there be? If I get too many or too few, the steering wheel won't be able to turn enough, and the cable will probably break again pretty quickly. Best thing to do it count how many turns are in the ribbon cable before I take it out, but if I forget to do that before pulling it out....

[@googleplusisdead]

Fantastic, thanks! Not only clear and informative but well explained without a lot of extras and junk.

[@speedkar99]

Thanks for the feedback

[@pez6056]

G'day, I have a problem with the horn not working in my Hilux, after watching your excellent video I'm confident that I can do the repair myself. Thanks for taking the time to make such a clear and informative video. I look forward to watching more of your content.

[@myndcrym]

I went through half a dozen videos before I found yours. It is by far the best most informative video that I found. I will be replacing mine later today while using your video as reference. Thanx for a great video.

[@speedkar99]

Glad you enjoyed it

[@andygarcia5577]

yeah gotta do my TUNDRA I had'nt used my horn in like forever but cruise control has been out for aminute buddy asked to borrow truck for drivers test MECHANICAL FAIL on vehicle becuase horn would not sound so no drivers license went to NAPA bought fuse kit for $33.00 but the fuse puller tool was way to big for under dash fuses needle nose only to find fuse was good so now its thisCLOCK SPRING crap gonna bitch slap the engineer /designer being soooCLEVERLY STUPID

[@waynegardner5061]

Thank you...one of the best "how to videos" I have watched. Loved the tearing apart and explanation of how the clock spring works.

[@speedkar99]

+Wayne Gardner I love the tear down too. Makes it easy to understand how it works and how the clock spring can fail. Thank you

[@wangofree]

Excellent video. Before mounting the CS I would turn it until it reaches the end, then turn it back 2.5 turns so I'd know it's dead center. It has a 5 turn limit from complete close to open or vice-a-versa. :-)

[@zachalles7428]

My dude! I can't thank you enough!! Your engine removal video gave me the confidence for doing an engine swap after mine finally petered out and the only other thing I wanted to fix was the clockspring. Helping keep me sane with a fun project during the corona. Hope you're well

[@speedkar99]

Glad this helped

[@saddammalima8458]

I wanna know can I kinda make my own make shift clock spring with audio control

[@neppy5]

another great high quality video, never heard of/saw a clock spring before this, very informative

[@speedkar99]

Thanks for the feedback, glad you learned something

[@btnerual]

Nice work, straight to the point and clear explanations of what you are doing. Thank you

[@ohyeah6729]

Well done. Very professional. And no kids running around making noise in the background.

[@speedkar99]

Haha no kids or cats I try to make it straight and to the point

[@Frandon33]

A really informative how to video. The rip down of the spring clock really helped .I am now going to attempt to replace my seat Ibiza spring clock with a lot of confidence. Many thanks.

[@speedkar99]

+Don Cameron thanks I'm glad you found this useful!

[@RanciDMonkeY01]

That was great to see how the system is made. To think that in Canada the Toyota dealerships are charging 600$ for a ribbon wire, contacts and super high end plastic engineering.

[@speedkar99]

Get a used one from the junkyard!

[@FlyMeAirplane]

Yup, same with my Hundai. I got a new spring off ebay for $22 tho! Took less than an hour to install.

[@julybear8019]

Hands down one of the best video presentations on youtube.

[@sonyacarpenter8261]

Thanks for a great video, I love how you publish your skills to help others save hundreds in labour that is so DIY, thank you!

[@speedkar99]

+Sonya Carpenter Glad it helped. I do this firstly for myself to document my experience and then to help you.

[@larcat3148]

This is by far the best video I've seen so far on KZbin, now I understand how the clock spring works.

[@speedkar99]

Glad it helped

[@obaid.371]

Wow , that's a great video, Clock spring is so simple designed. I thought it was contains bearings and some complex ..

[@N4sir98]

Excellent video! My cruise control on my 2009 Yaris (332,000 miles) has stopped working, and after checking fuses and replacing the cruise control stalk, my cruise control is still not operating. Further inspection revealed that it will work sporadically depending on the position of the steering wheel which makes me believe my clock spring is faulty. Thank you for creating this video!

[@k.backus6349]

The best and most useful video on changing this out. Thank you! Heading out to DIY now.

[@speedkar99]

All the best

[@k.backus6349]

@@speedkar99 finished in less than 2 hours. Everything working like new. Thanks again.

[@lorenzoparedes2306]

A most impressive video, straightforward and informative. Most YT instructional videos obligate the viewer to see a batch of BS with a selfie part in the video. I don't have a Toyota, but I am currently experiencing some issue with my German car. removing the steering wheel from it is not as easy as on your vehicle. Thanks.

[@husseinel-hajj7818]

Hey thanks for the video, but I must share a useful tip that you didn't do (and it was dangerous somehow not to do it): When removing the central screw for the steering wheel, unscrew it about half-way, and wiggle the steering wheel as if you were going to remove it completely. Given that the steering wheel usually gets stuck or kinda "glued", doing so will prevent you from getting a SMACK IN THE FACE or injuring yourself!! So: 1- unscrew the screw half-way / 2- give the steering wheel a wigle and pull it towards you to free its "glued" state / 3- the steering wheel is now loose, continue unscrewing the screw and remove it, then NOW it's safe to remove the steering wheel.

[@LRS905]

Good video and a very good explanation of what goes on there. I am amazed at the relative complexity of this, compared to my old 1989 BMW 316i. I removed once the steering wheel and what it had was a brass ring mounted on the back part of the steering wheel, while on the steering column there were a couple of protruding brass buttons, mounted on springs. These buttons were always out, pushed by their springs, and when one installed the steering wheel, a permanent contact was made between these buttons and the brass ring on the back ofthe wheel, therefore, no matter the wheel's position, there was always contact between the controls in the wheel and the steering column. I thought it was a very sturdy and simple solution, compared to this damn reel of cable inserted on the steering column.

[@speedkar99]

+RL R I for see there being some contact issues with that design once things start wearing down. With the amount of buttons on the steering wheel controls, there isn't enough room behind the steering wheel for slip rings. You now resort to a clock spring with a chip to communicate to the CAN BUS.

[@geodeaholicm4889]

excellent concise explanation and demo. i appreciate the safety precautions on the airbag too. the spiral thingy on my '07 prius went tilt & i will soon replace it, aided by your fine vid.

[@speedkar99]

+GEODEAHOLIC M thanks, it should be similar to replace on your Prius

[@Rumeel12708]

Crazy how simple this is yet we are so technologically advanced but simply functional. Need to change this on my 05 taco, air bag blew and horn glitched here and there so I disconnected it

[@speedkar99]

Agreed. Did you crash or it just blew?

[@Rumeel12708]

@@speedkar99 it was crashed, I bought it salvage, was working great fore a while but then it slowly started to honk here and there to the point where it would honk when the truck would be off.

[@whereisarthur]

great video, thanks so much for taking the clock spring apart and showing the components!

[@speedkar99]

Glad you learned something. I always enjoy taking things apart

[@BKTX]

Hey Speedkar99, I used your vid to replace my 1998 4Runner clock spring. Horn works like a charm now! The directions were identical with the exception of the left torx bit cover. Mine were two circular covers. For the benefit of others to improve on your otherwise excellently shot and narrated video, I'd mention to apply the tape at the top and then cut it. Also the torx bit size for mine was a T27, which I'm sure was the torx bit size on yours too. Total time was about 45 mins for me as I misaligned the wheel by a spline or two, totally forgetting I put the tape there!

[@speedkar99]

+Bob Kim I'm glad my video helped. Thanks

[@jumpinjohn54]

2nd time around having to do this on my 2007 RX 450h. Lasted about 5 years! :( Thanks so much again!

[@speedkar99]

Awesome. Glad it helped

[@hanialsisi]

may i know what is the symptoms if this part goes bad or faulty? as i have many errors like Malfunction VSC, ABS, Traction Control & Cruise Control with Radar Malfunction as well as when i took my RX350 for the inspection they said it may cause of the bad cable spiral clock (Not Sure) and i hesitating to change it as it wil cost me 500$

[@adejorogloryisaac3410]

@@speedkar99 hello Sir... . I really which to know you more am an automobile engineer but I need more knowledge sir. I will be glad if you accept my request...

[@adejorogloryisaac3410]

Thats great ooo...

[@brendawarren5188]

Excellent, concise, informative video. We're going to use it to change our clock spring. Pray it works. Should we test it first to see if it is the cause of the airbag light coming on? The ECU was already changed and the airbag light is still on.

[@speedkar99]

+Brenda Warren You should test the airbag and its wires...there's resistance values in the manual

[@tatofonico]

I love the format of this video, super fast paced =) keeps you paying attention at all times Maybe you can answer this question.. is the steering angle sensor within the clock spring on modern cars? I have a 2015 Scion FRS and I'm thinking my steering wheel is not exactly centered on the gear teeth of the steering column, because i replaced the inner tie rods, and when putting the tie rods back together, i counted threads on both sides to make them even, and the steering wheel became a good 15 degrees offset from top dead center when going straight. Of course, they fixed it on the alignment rack by screwing in one side's toe arm a good amount of threads more, but I'm thinking the correct thing to do would be to set both toe arms equal and then move the steering wheel one or two teeth over. I'm just afraid the steering angle sensor will be all off

[@cotick]

Thanks! Your videos are perfect. Short and informative without watching for hours how folks turn nuts and bolts.

[@speedkar99]

Thank you, short and to the point is my style!

[@adejorogloryisaac3410]

@@speedkar99 I love that...

[@erichandyauto]

You sir are the cat's meow! Thank you for sharing. BTW, proper torque specs on steering wheel nut: 2001-02 Models: to 25 ft. lbs. (34 Nm) and 2003-05 Models: to 37 ft. lbs. (50 Nm)

[@speedkar99]

You are welcome!

[@exiguous1]

absolutely the best how to videos.no BS

[@Hoytman225]

Exactly what I was looking for. Very detailed.

[@speedkar99]

Awesome, thank you!

[@mathewdavis-adventuresandd6643]

Thank you. Now I know what that flat white cable was that came out of my daughter Jeep Wrangler steering wheel column. Looks like I have some work ahead of me.

[@damianmorfin1506]

Thank u so much!!! Worked on my lexus 🙏

[@7jack7]

Thank you for making this excellent video! Top Notch!

[@speedkar99]

Glad you appreciate it

[@jacobekoba200]

A beautiful video clip right there derived from knowledge and experience.I have watched some video clips on a similar subject but not well explained.thumb up for you brother

[@speedkar99]

+jacob ekoba Thanks I'm glad you appreciate it

[@waynealty4287]

So well done and informative. A big help in understanding this process, even though my car is a different make and model I can see it will be very similar. Thanks so much.

[@speedkar99]

Thanks I'm glad you found it useful

[@aashaygamer]

Very nice and informative, can you also make some videos on how can we replace motion sensor in steering column, would be great.

[@speedkar99]

Thanks Good tip

[@shingabiss]

Very good video. One thing, the stearing wheel nut should be properly torqued to 37 ft lbs with a torque wrench.

[@Jason-Jason]

Excellent video! Thanks for the disassembly! Excellent job

[@speedkar99]

You are welcome

[@kevinbowrin8385]

Using the tape to mark the position is such a smart idea.

[@speedkar99]

Kevin Bowrin Agreed. The paint on the spline didn't work so well.

[@travisfeld97]

Great explanation! I have an 07 Tacoma and replaced my clock spring (spiral cable) because of an airbag light. Went off for two weeks and now it’s back😢. Any ideas what could be causing this?

[@mb1636]

Wow !! Great vid ! I recall the old cassette tape. Thank you !!!

[@coolissimo69]

Great Video, Bro can I ask you , if the car is pulling to one side in my case left, and all the four wheels are aligned . I can hear a small knock sound when I turn the wheel all the way left or right, its a very small knock. What could it be?? There are people saying is something with the clock spring, a plastic inside the steering wheel is wear out, or something like that . What is your thoughts, Thanks.

[@ahmadalsamaraiy3400]

Good way for explanation , bravo, I have corolla 2007 , it's not much different ofwhat you explain. most of the Japanese cars has the same way of replacement for (clock spiral) , I think the rest car brands have the same similer way, just some little differences Thanks for your good effort

[@speedkar99]

+Ahmad Al Samaraiy Thanks, yes the procedure is similar for many cars, involving airbag and steering wheel removal.

[@WILFREDTSIKAH]

Great video. should be an easy repair for me now if mine ever breaks

[@speedkar99]

Yep! I'll have a Honda clockspring video coming up

[@kevinbarker3965]

Gen2 Prius - I found that the Torx screws must be removed. Also the Airbag connections are different. Pull out the yellow center tab to release the wires. The steering wheel would not lock, held it while loosing and tightening the 19mm nut.

[@speedkar99]

+Kevin B thanks for the tips. I expected it to be similar.

[@BOBspellitbkwrdsSMFS]

i cant believe that they cannot create a better system than this

[@speedkar99]

+BOBspellitbkwrdsSMFS its not that hard is it?

[@BOBspellitbkwrdsSMFS]

at least for the horn, i had a 65 beetle and the horn was just a mechanical connection no wire. seems that would be a better option.

[@aevoss]

BOBspellitbkwrdsSMFS who is they?

[@charvakkarpe]

I actually think the spiral cable of the clock spring is really clever. Beats having sliding brush contacts that can corrode. How else would you do it?

[@JohnSmith-uy7sv]

Your good. Very informative.Thanks I have a 99 toyota sienna but the horn will work if I push or pull on the steering wheel and it makes connection that way. Sounds like bad terminal connection instead of the ribbon cable as that would not effect anything by prying or pushing if the cable was bad. Thanks.

[@speedkar99]

+John Smith agreed, there's something touching under the steering airbag.

[@Billymons]

Excellent video!!! Keep up the good work!

[@speedkar99]

Thank you! Will do!

[@ryanchenier-poulin8570]

Learned something. Thank you.

[@speedkar99]

Glad to hear it!

[@Ilovecomedy7]

3:00 Thanks for showing us the inside. My problem is that whenever I drive, I started hearing rattling noise inside my steering wheel. I put pads on headlight and wiper switches attached a metal plate on the steering and tied up any loose wires, but I still hear the noise. I bet this spring wire keeps moving back-and-forth on mine.

[@jwdonal]

Really interesting vid. Cool to see how it works.

[@speedkar99]

It sure is neat!

[@andycumberbatch4140]

Good video, but remember to apply thread locker to the steering column nut to avoid it backing off.

[@speedkar99]

Good idea

[@marvingjimenez7252]

Cuando el horn sigue pitando puede ser el clock spring ya está fallando ?

[@Gustavo9823]

After this turn on light dsp y dps, do you know something about it?

[@sanferminhotsauceco8222]

Outstanding video, you taught me a lot and saved me money. Great job

[@speedkar99]

Thanks

[@johnnyjackson9641]

Your very good at this keep up the great work!! Thanks

[@speedkar99]

Thanks

[@jackmoore5847]

Excellent how to! Very informative!

[@speedkar99]

Thank you very much.

[@MrSatchelpack]

In the video the clock spring is the culprit for things not functioning, but what is the first thing to check if the horn isn't working? Fuse? Contacts? Thx.

[@Eric-xt3os]

Huh.. I figured I would need a mechanic to replace this, but I’m guessing I could probably do this.. it doesn’t look like anything major I could do wrong that would lead to major problems, that I couldn’t just retrace a few steps and get back on track, right?

[@speedkar99]

Yes it's pretty easy

[@buvleiz6917]

Excellent video

[@Joaquin77]

wow, a very good video explanation! i need to do that to my 2007 sentra and i think is a very similar procedure. Thanks for the video help!

[@speedkar99]

+Joaquin77 Thanks, best of luck on your clock spring replacement.

[@mattbono2815]

Thanks for another great video! Never knew a clock spring even existed. Do you have to worry about setting a code that would have to be reset by a dealer since you're removing the airbag?

[@speedkar99]

+Matt Bono As long as you don't turn the ignition ON with the battery connected, the car's computer does not know that the airbag was removed. As an aside, you don't have to take the car to a dealer to diagnose airbag codes. For $25 you can get a techstream cable and do everything the dealership can do: kzbin.info/www/bejne/gXXTnZd3q5Woh6c

[@mattbono2815]

+speedkar99 that was a cool video. I like the way tech stream allows you to personalize settings

[@chisangamphana2729]

You're the man, keep it up

[@speedkar99]

Thanks

[@mikef6706]

Does your vehicle have DSTC (dynamic stability traction control) If YES, did you have to calibrate your SAS (steering angle sensor)? Thank You Great Video 👍

[@kevinstaunton1264]

Very Informative, well made video. It was a great help. Thanks.

[@speedkar99]

+Kevin Staunton thanks glad you learned from it.

[@Golf4org]

Good video. But better turn the Ignition on before connecting the battery. So in case (you did something wrong and) the airbag detonates you are outside the vehicle.

[@solexxx8588]

No

[@giantgigante7725]

Thanks bro. For the video saved me. $500 in labor and instalation from the toyota dealership. ,. I got a question are you able to fix the old clock spring because mine causes the airbag light to come on and i wanted to know what caused it to come on and what was defective on it ? Before i buy the replacement piece maybe i cud. Fix the old piece would it be the connection part or something.

[@speedkar99]

Glad it helped

[@giantgigante7725]

@@speedkar99 appreciated bro. For the explaining and the time u took to make this video; very valuable info. .. 👆👨🏻‍🔧💯👍

[@tedjohnson64]

Excellent tutorial!

[@neilcarhub1182]

Airbag haito any problem with traction control

[@christianfoster8400]

I have a clock spring code but my horn and everything works just fine. Should I still replace the clock spring? I can get one cheap.

[@a13jo]

Do it

[@jonathantekle_]

The best auto youtuber.

[@1drhnsd1]

Great video showing the insides of a clock spring. I wonder if someone sells those ribbon cables with the correct connectors installed - anyone know where to get them for various cars?

[@polpotube]

thank you so much!

[@hopeton4221]

Clear & understandable

[@Whereintheworldissummer]

Thanks for the Awesome video! I think I’m going to do it myself

[@Nawafeno]

Great video, any idea how much is the original part for 2007 Lexus ES?

[@speedkar99]

Get a used one from junkyard

[@Nawafeno]

@@speedkar99 Will do, thanks

[@lareina2065]

Nice video.. my service air bag light is on and the steering makes a scratchy plastic noise when turning the wheel can this be my clock spring please help

[@kuyaasada]

Anything you could do to put the clock spring back together if it comes untangled? the cover came off somehow when replacing the steering wheel signal lever. Would you need to buy a new one and replace it?

[@acrepairnearme]

Thanks man. I was scared to open my. Bu the way 6 pin connection part for sienna 2000 gonna cost 350$. Looking for repair.

[@speedkar99]

All the best on the repair

[@outdriving08]

With modern cars, do they ever route any CAN BUS wires through there as well?

[@billl3936]

Every thing but the horn works on my 2000 toyota sienna. Should I replace clock spring or is another connection to check in steering? Horn works when i hit panic on key bob.

[@speedkar99]

Check it with a multimeter first.

[@briantm488]

My steering wheel is making a squeaky sound when I turn, could a bad clock spring be an issue ?

[@pierreduforest9215]

Très bien expliqué Merci

[@phillipcuster8036]

So mush more than just power to the controls. It plays a big part in your traction control.

[@speedkar99]

Traction control?

[@phillipcuster8036]

Yes. The computer reads the direction of the tape to know the angle of the steering wheel to know what wheels should get power. My friends clock spring popped off on his Jetta when he did a steering wheel swap and the spring came undone and permanently lost his traction control

[@jeffhein7275]

Very informative and a highly professional presentation -- Thanks!

[@speedkar99]

Glad you enjoyed!

[@wd6691]

First time performing this task. Thought your video was helpful...until I realized you have to rotate the clock spring until it stops then rotate it 2.5 X counter clockwise before you install it. You missed a key step fella!

[@speedkar99]

Yes resetting that is important

[@vickyvictoria4u]

Oh I missed that. I just had mine installed and it didn’t work.

[@vickyvictoria4u]

Should I go back and do that rotation and maybe it will work?

[@Pat-Van-Canada]

huge help as always

[@jcastro41]

im trying to remove my clock spring and have had no luck removing the airbag wire from that “heavy duty tab” you mention....any tips would be hugely appreciated!!! i really don’t want to cut the wire!

[@doinikinsv2385]

Do i have to set clock spring rotation halfway before installing it? Just worried it might break the ribbon if not properly set while steering it .

[@speedkar99]

Yes

[@br31woodlands69]

Really good video. Clear and to the point. Thank you.

[@speedkar99]

You are welcome

[@bigbigspoon]

Good video, Thank you!

[@speedkar99]

+bigbigspoon thanks

[@EsDACcompany]

I wasn't aware these thing (clock spring) even exist till now. Question is though, is this thing go bad very often?

[@speedkar99]

EsDACcompany Clock springs tend to go bad but more so in other makes than Toyota's.

[@markrainford1219]

An F1 car must have an impressive one. Though I suspect they use a data BUS.

[@thaquickstaa4174]

what would be the result if you brake the spring? can it make the airbag go off

[@quirinonavarro1857]

Very good information...

[@specialized29er86]

I was wondering what they meant, I was thinking something to do with the clock.

[@EvendimataE]

i got the same battery yesterday for about $80 from firestone....best deal :D