Spektrum Smart Receiver AS3X Setup Series #5 - AS3X Tuning with Gain Channel and Flight Mode Setup

  Рет қаралды 62,518

SpektrumRC

SpektrumRC

Күн бұрын

Пікірлер: 44
@iflyrc5
@iflyrc5 4 жыл бұрын
This is an excellent video series but for us folks that have not been using flight modes it is very confusing. At 1:42 minutes of the video it says something about the flight modes that we had setup earlier, however, I go through Series 1-4 and there is nothing about setting these up so how was I supposed know to do this before? I really like the concept of the forward programming with these new smart RX but for those of us have not been using flight modes it is very confusing. Also, from what I understand there are RX flight modes and TX flight modes which even makes if further confusing. Guys - keep up these videos but just please remember that you do this every day and have been doing it for years. Think of your audience here. When I was working and had a complex set of instructions to get out to our fleet guys I would have some of the administrative folks in the office do the process. The had only limited knowledge of the process so it was a great way to check if it was a good process to send out to the fleet.
@janrc
@janrc 4 жыл бұрын
The flight mode must be configured in the flight mode settings. There are 5 flight modes overall. The 100% = fm mode 1, 50% = fm mode 2, 0% = fm mode 3, -50% = fm mode 4 and -100% = fm mode 5. Now check what gain your switch cause.
@williewideback
@williewideback 2 ай бұрын
My setup are as followed: Flight mode 1 is AS3X setup using the Gain nob to adjust the roll and pitch, also to rotate counter clockwise to turn off the AS3X if desired. Flight mode 2 for safe select self leveling and Flight mode 3 for Envelope.
@kokokyoushi
@kokokyoushi Жыл бұрын
How do we know WHICH channel to assign to the switch for flight modes?? 1:34 - 2:01 is very confusing1
@ak-pn8vm
@ak-pn8vm 3 жыл бұрын
Are Spektrum products only designed for its employees? I find most of the videos confusing.
@joenaylor34
@joenaylor34 3 жыл бұрын
After a lot of fiddling around I figured out how to get this setup to this point with my older DX6. The key was to first update the radio software, then before getting into the Forward Programming I went into System Setup and set the channels such that the Gear Channel was set to Switch D and Channel 5 and the Aux1 Channel was set to Channel 6 and Switch B. For some reason the updated software for the radio shows a Channel 7 which of course does not exist on a 6 channel radio, so this Channel 7 needs to be set to inhibit, otherwise strange things happen. After this I started over with video 1 (for about the tenth time) and was able to progress to this video.
@DI4L
@DI4L 3 жыл бұрын
This was awesome, thank you!
@markdcarey
@markdcarey 2 жыл бұрын
I have watched this entire series over and over again and I think I finally have it right EXCEPT for this one issue. It looks like SAFE has to be associated with a flight mode. What I really want is to flip switch A to turn on SAFE only when I get in trouble (switch B is for flight modes) and turn it off again once things stabilize, regardless of the flight mode. What am I missing here?
@SpektrumRCvideos
@SpektrumRCvideos 2 жыл бұрын
The best way to do this would be to use the Flight mode menu to setup 2 switches for flight modes. Then you will be able to use A and B for up to 5 different flight modes. Also make sure that the channel you are using to control flight modes on your AS3X is assigned to the FMODE (flight mode) switch (not B or A specifically). Hope that helps!
@Pretorian435
@Pretorian435 4 жыл бұрын
Curious. How does he have AUX 4 on a 6 channel receiver? Also, hasn't he used up all the channels on that aircraft? Throttle, Ailleron, Elevator, Rudder, Gear, Aux 1(Flaps)?
@akbarshoed
@akbarshoed 2 жыл бұрын
I've read every comment and have watched each video over and over. I've also watched others. GAIN. What precisely is gain in this context. In Radio, "gain" refers to the recievers ability to pick up a transmitters signal. So, instead of increasing the range of the transmitter we make it easier for the reciever to pick up the signal by increasing the reciever's "gain". Is this what we're talking about? If not, please tell me what "gain" is referring to specifically. Also, why do I want to keep messing with gain once no oscillation is achieved? Why would a change the gain in different flight modes?
@joe92
@joe92 2 жыл бұрын
Gain in this sense refers to the ratio of change in the input to the change in the output. As an example, an increase in roll channel gain will result in a more aggressive response to un-commanded roll. Gains are discussed extensively in feedback control system theory. Changing gains for different flight conditions is useful because gains for one condition might not be appropriate for another. An example would be different gains for cruise or landing configuration because you might need larger gains at lower speeds to get the same response you might have at cruise speeds.
@charles7112
@charles7112 2 жыл бұрын
I have an AR636B and have updated the software using the cable but when I go to do the forward programming I keep getting connection failed. Not sure what to do next. I have the DX 9
@SpektrumRCvideos
@SpektrumRCvideos 2 жыл бұрын
AR636 receivers do not support forward programming.
@charles7112
@charles7112 2 жыл бұрын
@@SpektrumRCvideos Thanks, I figured that out after taking a hammer to it. Just kidding, I did finally watch a video that confirmed what I needed to get it working.
@putzytart
@putzytart 4 жыл бұрын
HELP. I'm on a DX8 and I'm struggling with the gain channel select and the Flight mode channel select. Upon set up, for Gain channel select, I can only see AUX 3 Rknob in my available channels, even though AUX 2 is completely free and assigned to use switch D. So when I then go to Flight Mode channel select, I can't choose AUX2 on switch D, which is all assigned. I've checked everything all my channels are free, they are assigned perfectly and no flaps, mixes, throttle cut, or anything else uses those channels. Can someone help me with this?
@putzytart
@putzytart 4 жыл бұрын
I've tried so many things so many times. Am I missing something? I can't get it to use Aux2 for Flight modes, and Aux3 for gains. Tried and tried and tried. Please do help me!!!!
@janrc
@janrc 4 жыл бұрын
You have to assigne the FMode to the channel AUX2. Take care you have configured the Flight mode in your model in the radio first. Do not assign the flight mode switch directly to a channel! If you do not have done this I suggest you reset the receiver, configure the flight mode and after that start again with the forward programming.
@mikebingham1454
@mikebingham1454 3 жыл бұрын
According to my Tx and Rx everything is set up. When I turn it on while installing as3x it wiggle 1 time but after I hit caplets I can't here anything or nothing moves in all 3 settings
@RedZone54
@RedZone54 2 жыл бұрын
When I capture gains, are all flight modes captured or just the selected flight mode.
@SpektrumRCvideos
@SpektrumRCvideos 2 жыл бұрын
Is per flight mode
@RedZone54
@RedZone54 2 жыл бұрын
@@SpektrumRCvideos THANK YOU!
@larryhuck4504
@larryhuck4504 3 жыл бұрын
Can the potentiometer be used to adjust the gain on only one surface at a time? And, can that one surface gain be captured without effecting preciously captured gains for the other channels?
@SpektrumRCvideos
@SpektrumRCvideos 3 жыл бұрын
Sure can. There is a menu that you can use that allows you to make 1 axis(surface) adjustable and the others not. Hope that helps!
@christalcott1832
@christalcott1832 2 жыл бұрын
@@SpektrumRCvideos which one please?
@jungmeisterKN
@jungmeisterKN 4 жыл бұрын
Excellent
@OkieBart
@OkieBart 4 жыл бұрын
So for those of us with the DX6e who have no knobs or sliders........what do we do?
@SpektrumRCvideos
@SpektrumRCvideos 4 жыл бұрын
You will need to go into forward programming and adjust the gain values between flights.
@LivinTheDream-LV
@LivinTheDream-LV 4 жыл бұрын
I have a Dx8 and when I get to the step of assigning flight modes the only channel open is Aux 3 which was previously assigned to the right knob to adjust the gains. Why can't I see Aux 2 as being available?
@putzytart
@putzytart 4 жыл бұрын
I Have the same problem!!!!
@putzytart
@putzytart 4 жыл бұрын
Did you manage to sort this out?? This receiver is pointless if I can’t get as3x and safe programmed.
@LivinTheDream-LV
@LivinTheDream-LV 4 жыл бұрын
@@putzytart , yes, I did. Try this. Delete the model you are trying to get working and start with a new model. Set up the plane as the manual instructs you to do (wing type, flaps, etc.) and BEFORE you go into Forward Programming go into Channel Assign, then go into the 2nd screen under that. Here you want to scroll down to the Aux channels and assign the switches you plan to use in Forward Programming. I assigned Switch G to Aux 2 and R Knob to Aux 3. My plan was Switch G would be for Flight Modes and R Knob would be to adjust the AS3X gains in flight. After the plane was completely set up and flyable I went into the Forward Programming and then I could see all my Aux channels when I was trying to assign the switches to the AS3X gains and Flight Modes. After talking with Horizon the following day they confirmed that you have to assign those switches BEFORE you start Forward Programming. The videos don't say anything about that so its easy to skip over it. Hope that solves your problem - good luck! If not, call HH tech support. I think I spoke with Shawn and he new exactly what I did wrong.
@putzytart
@putzytart 4 жыл бұрын
@@LivinTheDream-LV HA! I hadn't read your reply and I managed to just get this sorted and came here to let you know. I had a number of people at Horizon working on this and no one could sort it out! Just tried a last ditch attempt of building a new model from scratch and it works!!! Yes like you said I assigned my channels first. I guess I must have set up forward programming last time before I set up my proper channel sign and from there like you say it doesn't matter what you do it's too late. Will have to go back and copy all my settings over (I already had this plane flying perfectly with dual rates and expo etc), but that's easy enough. Can't wait to fly now!!!!!
@janrc
@janrc 4 жыл бұрын
AUX2 is already assigned to an input. Take care this is not the case.
@gitup73
@gitup73 Жыл бұрын
Well, I WAS excited about installing this receiver into my avios bushmule, but watching this? Waaaaaaay to technical. I guess I'll go with the standard 6 channel orange hobby King
@franks213
@franks213 4 жыл бұрын
Is there a PC programmer for doing this?
@SpektrumRCvideos
@SpektrumRCvideos 4 жыл бұрын
No there is not at this time.
@ArieteXT10
@ArieteXT10 3 жыл бұрын
@@SpektrumRCvideos Will there be ever?
@cesar68033
@cesar68033 4 жыл бұрын
On my dx8 it still shows only flight mode 3 nothing changes
@BlvlWmpower
@BlvlWmpower 4 жыл бұрын
That is dumb. Is your firmware up to date?
@cesar68033
@cesar68033 4 жыл бұрын
Yes it up to date my flight mode are on aux 1 and it can’t be changed even if I assign it to switch f it stays on switch d so it working with my flaps only not allowing me to selects my own channel
@janrc
@janrc 4 жыл бұрын
The flight mode must be configured in the flight mode settings. There are 5 flight modes overall. The 100% = fm mode 1, 50% = fm mode 2, 0% = fm mode 3, -50% = fm mode 4 and -100% = fm mode 5. Now check what gain your switch cause.
@kokokyoushi
@kokokyoushi Жыл бұрын
I find this completely confusing and frustrating. I don't see how the knob for gain adjustment is assigned to the switch. I can not get this set up on my NX8. It is NOT simple!
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 45 МЛН
IL'HAN - Qalqam | Official Music Video
03:17
Ilhan Ihsanov
Рет қаралды 700 М.
The evil clown plays a prank on the angel
00:39
超人夫妇
Рет қаралды 53 МЛН
100 Mph with NEW CASTLE MOTOR! 1512 2650kv
8:35
Innovation RC
Рет қаралды 2,3 М.
IAC Unlimited Known Pitts S1S
3:25
Dave Scott
Рет қаралды 177
Setting up AS3X and SAFE with Forward Programing-AR631-AR630  by FGFRC
22:08
How to Calibrate the Controls in the Spektrum iX14
2:46
Spektrum Smart Receiver AS3X Setup Series #3 - First Time Setup
6:22
FrSky ETHOS Programming B2EMO Droid Head Tilt Weighted to Head Lift
19:09
FrSky Ben - RC Live Tech Support
Рет қаралды 461
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 45 МЛН