Thank you for this. It seems like nearly every “Tamiya complete build” video skips all of this, and I for one needed this exact explanation. Great job, thank you!
@djcutlas19762 жыл бұрын
Video was very helpful. Thank you..... I haven't had an RC car been over 30 years.... A lot has changed
@richardmason6172 жыл бұрын
You just saved my life . Boxing day for my 8 year old building the LUNCHBOX. Simply followed your setup 👌 👍 thank you so much 🙏 😊
@spudskirc44582 жыл бұрын
You’re welcome. Glad it helped you out 😃🎉
@petrolhead282 жыл бұрын
Cheers mate. Far more sense than the tamiya instructions! Now to finish the kit that this stumbling point has been overcome.
@jamesbath10273 жыл бұрын
You have literally saved from me a world of pain and frustration with this video. Thank you. Am off drifting with my new TT02!
@spudskirc44583 жыл бұрын
Glad to hear it helped 😀👍🏼
@martinbuff13 жыл бұрын
thanks bro!!!! Superrrrrr helpful video you are the man!!
@larsbee2 жыл бұрын
@@spudskirc4458 how to do a factory reset?
@lancairw8673 жыл бұрын
Thank you. Have a Tamiya Frog and hooking up a new Traxxas TQ receiver and transmitter. Forward and reverse were opposite of the trigger. Last step worked and I had at first I had ESC in channel 1 and no motor operation. So I switched to ch 2. You solved both 👍🏼👍🏼 “cheers” from the US.
@spudskirc44583 жыл бұрын
That’s great, I’m glad to hear the video helped and you got your car running 🙂
@leehartwell68273 жыл бұрын
thank i keep forgetting the basics that you show ,well done man your a great help ,reading the manual is confusing lol
@spudskirc44583 жыл бұрын
No problem glad it helped 👍🏼
@iannewman42223 жыл бұрын
Thanks, like others i was totally stuck with the instructions provided. This worked first time!
@spudskirc44583 жыл бұрын
No problem glad it helped 👍🏼
@2569sean2 жыл бұрын
Am same as many comments on here this bit was sending me mad and giving me a migraine. Thanks alot top man
@spudskirc44582 жыл бұрын
Thanks glad it helped.
@davewarner84013 жыл бұрын
Best video for sorting out all your problems with these tamiya speed controllers Thank you so much!
@spudskirc44583 жыл бұрын
Thank you glad to hear it helped.
@schuttrostig57292 жыл бұрын
Verry good video. I always forget how to setup and this video explains the important settings. Now when comes the advanced tutorial: - change the voltage cutoff to a higher, lipo correct value - modify the circutes to run the servo at full voltage (HV servo) - use two speedcontrolers on channel 2 and 3 (for whatever reason)
@mark-1rc5023 жыл бұрын
Thanks for the video 🙏 it was a great help, This ain’t exactly my first rodeo but it’s my first Tamiya ESC, I couldn’t understand the instructions it’s not clear enough. The video saved the ESC from the Hammer 😁 Thanks .
@spudskirc44583 жыл бұрын
Nice one glad to hear it helped you 👍🏼😊
@idesignyou...9257 Жыл бұрын
Thanks for the info, finally got reverse working! lol
@spudskirc4458 Жыл бұрын
Glad it helped :)
@rossthercguy96372 жыл бұрын
Very very helpful, indeed, I was proper stuck but your video helped
@infinitycars62092 жыл бұрын
thanks for this man got my vw working properly
@spudskirc44582 жыл бұрын
No problem glad it helped!
@josephkebbi1146 Жыл бұрын
Thanks. I learnt from your video.
@jasoncroll84822 жыл бұрын
Saved me so much pain m8, thank you
@spudskirc44582 жыл бұрын
Nice one glad it helped 👍🏼
@jbstorming32502 жыл бұрын
awesome...straight to the point and great video. THANKS!!
@cbusbyuk3 жыл бұрын
Great video. Building my first grasshopper and was stuck at this point with the wiring. The Tamiya manual isn't the best to say the least. Cheers. 👍🏼
@spudskirc44583 жыл бұрын
Thanks, glad it helped you, the manual can be quite confusing.
@andyknuckles29032 жыл бұрын
Thanks. You got me reverse, man. 🙂
@gabrielelanzoni30753 жыл бұрын
thanks dude! thought my esc was broken !! it wouldn't reverse
@spudskirc44583 жыл бұрын
No problem, glad it helped :D
@danielmerrin96999 ай бұрын
YOU SAVED A HORNETS LIFE... 😂 THANKYOU BROTHER
@spudskirc44589 ай бұрын
Glad to hear it helped 😁
@parabola2073 жыл бұрын
Thanks, I thought the wire from speed controller went into the battery slot on the receiver now I know 👍👍
@spudskirc44583 жыл бұрын
No problem glad you got it working :)
@LeeLee-mu4we Жыл бұрын
Very helpful, thank you very much.
@joshuaharris47803 жыл бұрын
Thank you for this video I’ve got all the same kit really helpful
@spudskirc44583 жыл бұрын
You’re welcome, glad it helped.
@joshuaharris47803 жыл бұрын
@@spudskirc4458 my wires are yellow and green so was abit confused at the start
@will450ktm Жыл бұрын
A GOOD VIDEO ON HOW TO SET A RIGHT PAIN IN BUTT ESC
@temmeenglish88292 жыл бұрын
Spot on Vid. saved the day!
@chasescott98363 жыл бұрын
Thanks so much bro this helped so much!
@griceyboy3 жыл бұрын
Top quality video! Well explained and perfect
@spudskirc44583 жыл бұрын
Thank you, glad it helped :)
@farmerdawsy73813 жыл бұрын
Great video, really helped me out! Thanks a lot!
@spudskirc44583 жыл бұрын
Glad it did, thanks :)
@farmerdawsy73813 жыл бұрын
No probs, it’s hard to find accurate videos on you tube! Have subscribed. My car seems to go faster in Rev though so will have to re watch and have a play with it
@spudskirc44583 жыл бұрын
@@farmerdawsy7381 I’d try the end point calibration again if it’s doing that.
@farmerdawsy73813 жыл бұрын
@@spudskirc4458 will do, I’ll let you know how I get on
@farmerdawsy73813 жыл бұрын
@@spudskirc4458 I tried it, worked a treat! Quick question, I have the exact same set up as you, when in neutral it is making a buzzing noise! Any tips?
Any idea why my TT02 with TBLE-02S is accelerating upon startup without pulling the accelerator? Using FlySky FS-GT5 receiver and controller.
@460tahitii3 жыл бұрын
Thank you ! Big help .
@spudskirc44583 жыл бұрын
Glad it helped :).
@iulloa983 жыл бұрын
Gracias bro it really help us out we were stressing.lol
@fabricioaraujo6783 Жыл бұрын
Hello friend! does the quicrun hobbywing 1060 brushed esc fit the tamiya tt02 kit engines? can i use this esc?
@dangarvin56213 жыл бұрын
Thanks man I’m fairly new to the RC world. You saved me a headache and some time deffo get a sub from me 👍🏻
@spudskirc44583 жыл бұрын
No problem, glad it helped :).
@TheoCook3 жыл бұрын
Very helpful 👍🏻
@chrisparkin4313 жыл бұрын
Thanks, that has helped me setup hassle free
@spudskirc44583 жыл бұрын
No problem glad it helped :)
@catcancrunch72603 жыл бұрын
Hello, I have a question although we not supposed to turn on car first without transmitter on ! Should the car go into runaway mode if we do as others I have don’t do this ? Thanks Cat
@spudskirc44583 жыл бұрын
Hi, if you turn the car on first it can go run on its own, try setting your failsafe though to neutral this may help.
@catcancrunch72603 жыл бұрын
Done it thanks so much 👍🙏
@highflying822 жыл бұрын
Thank you.
@al13563 жыл бұрын
Thanks for the video, my son is no convinced I can fix anything
@spudskirc44583 жыл бұрын
Glad to hear it helped :)
@noidlbk32543 жыл бұрын
helps a lot, thanks :)
@spudskirc44583 жыл бұрын
No problem, glad it did :)
@SonnetGomes3 жыл бұрын
Hello Thank you so much for this demonstration. I noticed my RC car does not have drag brakes. It goes backward if i release the throttle while going uphill (neutral maybe?). Any idea how I can engage drag brake with this ESC if at all possible?
@spudskirc44583 жыл бұрын
Hi, you’re welcome. The esc doesn’t have a drag brake feature unfortunately.
@SonnetGomes3 жыл бұрын
@@spudskirc4458 Oh no...such a shame. It has advanced feature EV features like sensored brushless motors, yet it can't stay steady on a hill. I have to invest in couple of Quickrun 1060s. Thank you for this video though.
@Stantoneo143 жыл бұрын
Hi I got lunchbox monster truck kit for my 40th its built watched this video, I've now got reverse and stop but now forward on remote I have steering just no forward motion ,, when i press for throttle the green light flashes on tble-02. But nothing happens
@spudskirc44583 жыл бұрын
Hi, If you do the end point setup that should solve it.
@Stantoneo143 жыл бұрын
@@spudskirc4458 I've tried that get reverse an steering when I engage throttle I just get the green light flashes at me and no drive
@spudskirc44583 жыл бұрын
@@Stantoneo14 Sounds like it might be set backwords, if you unplug the motor wires and swap them does it then go forward and brake? If so then do the reverse activation which is on the video too.
@Stantoneo143 жыл бұрын
@@spudskirc4458 il give that a go later on and see what happens
@antz61303 жыл бұрын
My engine is rattling I’m built a Tamiya Grasshopper Do you know what the rattling could be?
@section233 жыл бұрын
Can you still configure it so the brake isn’t an option? As in just forward and back? Thanks for the other info in the video, really handy
@Manly3 жыл бұрын
I’m planning to buy a Tamiya RC kit Question: Can I use other ESC aside from Tamiya? Or It should be Tamiya ESC only? Ty!
@spudskirc44583 жыл бұрын
Yes you can use an alternate ESC. Hobbywing 1060 is a good choice if running brushed motors.
@Manly3 жыл бұрын
@@spudskirc4458 thanks!
@antz61303 жыл бұрын
Thank you 🤘🏼
@northy073 жыл бұрын
Hi, I’ve done a hot build and have a stick receiver. The car goes faster when going forward than reverse as expected. But the I need to pull the stick towards me to go and forward to break. Opposite as expected. Would the end point set fix this do you think?
@seth80053 жыл бұрын
maybe you can try to reverse the throttle channel setting on transmitter?
@jimcobain43813 жыл бұрын
Hi, How do you stop the break function so it goes direct to reverse?
@spudskirc44583 жыл бұрын
Hi, you can’t disable reverse on these.
@jimcobain43813 жыл бұрын
@@spudskirc4458 hi, I just want my ESC to respond like one of them old 3 step ones? They used to go straight in to reverse
@spudskirc44583 жыл бұрын
@@jimcobain4381 Unfortunately you can't with this ESC. A Hobbywing 1060 would be a good option if you're running brushed motors only.
@davidgould36573 жыл бұрын
Great video, Can you run 2s lipo on this ESC ? As I want to start running lipo battery on my Blackfoot
@spudskirc44583 жыл бұрын
Thanks. It isn’t recommended to run lipo as it doesn’t have a low voltage cut off so could risk damaging the battery. If you went and did it anyway use a separate lipo alarm to keep an eye on the voltage.
@seamustomlinson3813 жыл бұрын
Spudski RC trucks
@K4jo0o3 жыл бұрын
My ch2 not working with sanwa mt44 other radio works :( any idea?
@jarjarbinx713 жыл бұрын
Hi bud great video ! Just wondered why my esc is on a constant beeping and receiver has stopped not lighting up Cheers in advance 👍
@spudskirc44583 жыл бұрын
Hi, the beeping means no signal. Sounds like your ESC BEC output is no longer working so sounds like a failed ESC
@jarjarbinx713 жыл бұрын
@@spudskirc4458 ok cheers bud! Thanks for reply 🙂👍
@stevecroft54553 жыл бұрын
Hi I've got a lunchbox with tble-02s and have done activate reverse process many times now but still no reverse unless at random times at full pelt untill I push forward but then still no actual reverse I can control. Servo and everything eles is good. do u think I need to get a new speed controller. But thank for the video it was a big help 🙏 in getting me this far
@spudskirc44583 жыл бұрын
Hi, make sure the throttle trim is centred and try the end point set up on the video and then try it again.
@stevecroft54553 жыл бұрын
@@spudskirc4458 yeah it was centre terns out mine likes to be on full trim. I'm going to switch for a hobbywing 3300kv lipo set up so will probably need another video 😆 🤣 😂. Thanks for the reply 👍
@stevecroft54553 жыл бұрын
Will be doing end point tomorrow anyway thanks again
@ethanagun7353 жыл бұрын
Can u use any receiver and transmitter??
@spudskirc44583 жыл бұрын
Yes within reason, doesn’t really matter on brand.
@yibbyhechavarria3 жыл бұрын
I have some problems with the configuration can you help me please? Thanks for the video
@babyyoda10912 жыл бұрын
on mine it doesnt have channel 2 just names so what would channel 2 be
@spudskirc44582 жыл бұрын
What does it say on your receiver? It may say TH instead.
@joreldoherty47723 жыл бұрын
Can you help me troubleshoot my esc, Rx is bound, servo working set in channel 1, esc in channel two, no throttle at all, flashing green light and alarm beep when motor connected? Any ideas? Does flashing green mean it’s nit connected to receiver? But servo steering is? My brain hurts
@spudskirc44583 жыл бұрын
Is it a brushed motor? Which wires have you got it plugged into? Also have you tested channel 2 is working ok with a servo?
@joreldoherty47723 жыл бұрын
@@spudskirc4458 yeah brushed motor, tested motor it’s fine, haven’t plugged servo into channel 2, I’ll try this and see what I get, I assume it’s not intelligent and the servo will then just operate from the throttle control.
@joreldoherty47723 жыл бұрын
@@spudskirc4458 So, I think channel 2 is defective, when the throttle is plugged into channel one, the green light and alarm drops away and I had forward throttle, but with servo in channel two I had no steering, as soon as I plugged throttle into channel two, green flashing and alarm again which means it’s not picking up the receiver. This is annoying as it’s all brand new kit. It has been 25 years since I’ve built an RC though so I figured it must be something stupid, unless my radio controller channel two is defective but I doubt it?
@spudskirc44583 жыл бұрын
@@joreldoherty4772 Yes sounds like a faulty channel 2 then unfortunately
@robbo90203 жыл бұрын
hey bro, i only have steering and no throttle at all need help
@spudskirc44583 жыл бұрын
Hi, check the esc is plugged into channel 2 and then perfom the high point setup from the video.
@robbo90203 жыл бұрын
@@spudskirc4458 yeah nah I got it working but the motor keeps burning itself out, and there is no reverse when I get it working
@larsbee2 жыл бұрын
how to do a factory reset?
@jergames61092 жыл бұрын
it still flashes red for me
@spudskirc44582 жыл бұрын
Usually that means signal issue, check your radio is bound and the esc is in channel 2 of the receiver
@Polish_Pete3 жыл бұрын
can yo help me ? do you have facebook co i can video call maybe ? vant set up my car at all
@spudskirc44583 жыл бұрын
Hello, did you follow the video to wire and set the ESC up?
@Polish_Pete3 жыл бұрын
@@spudskirc4458 yep and it must be something elese not right.
@jasonlemmond30123 жыл бұрын
Mine still ain’t workin
@spudskirc44583 жыл бұрын
What’s happening with it or what is it doing or not doing?
@K4jo0o3 жыл бұрын
@@spudskirc4458 i have problem with no throttle on channel 2 (not working) but when switch 2 with 1 i can accelerate with steering and steer with accelerator, also when i turn on at ch2 it beeps and give tuncontrolable throttle for a while.
@evstratiosalisafakis87443 жыл бұрын
How do you find the Core 21 brushed motor? Looking for a fast motor than my torque tune one.
@spudskirc44583 жыл бұрын
They are good motors for the price but the standard ESC has a 25T motor limit for brushed motors so you would need to change the ESC if using a 21T. I would recommend a Hobbywing 1060 for value and quality.
@evstratiosalisafakis87443 жыл бұрын
@@spudskirc4458 👍 I got a 1060. Great speed controller for the price. I intend to run it in my TT01e. What pinion would you reckon?