Square body wiper switch, neutral safety switch, turn signal and ignition replacement

[@MTJ1986]

Used your video to help me do this while on lunch. Thanks man!

[@tebger]

Good video, jumps right into it explaining everything along the way. I wish all how to vids were done like this. I would never attempt tearing into my steering column without this.

[@zmurray9499]

Glad the video was helpful. Make sure you look inside that ignition switch hole before you take things apart, the key ignition. That was the most frustrating and took the most amount of time was to figure out how to orient that after not looking inside the column before disassembling.everything else was cut and dry

[@zmurray9499]

I will also add... don't buy the cheapest ignition switch. The actual switch at the bottom of the column. My first switch was faulty and I had to . the more expensive switch looked a lot more like the original switch. Take care

[@charlessalard4636]

T​@zmurray9499 took Pic as you said and still hard to set it.scared I was sure going to break teeth off....metal teeth to plastic teeth very smart...lololol

[@jacindarose5330]

Just the video I needed! Thank you so much for doing this!! Just replaced my dime switch & multifunction control switch & this video helped me figure out what we need to do to get it right!!

[@chevyguy7616]

Great video ! I started taking mine apart thinking . This guys stunned its not that hard ... yes its just like you did it . Dang iv got new cuts and some new muscles . Poped my arm out of socket to get the 8mil bolt for the starter switch. Just rediculis this has to be done this way . Great video for a step by step and how to avoid hours of mistakes . Took me about 2 hours doing it the wrong way then the right way haha . Thanx ! . 😂

[@zmurray9499]

I'm not gonna lie, it took me some time to figure out that the first ignition switch was faulty and how to get the rod put back into the keyed ignition switch correctly🤦‍♂️!! Your comment made my evening👍🏼

[@jenniferestrada5088]

Another great video!!

[@zmurray9499]

Glad somebody likes them🙄😉

[@briancraig7852]

Thank dude been looking for a video to replace my wiper switch that has not worked for 10yts, and all I see is guys pulling out the handle

[@edwardcokley9224]

So glad I atleast found another squarebody in yellow not the same yellow but close enough glad I stumbled across it

[@zmurray9499]

I would like to think that yellow is rare and desirable😃!!

[@edwardcokley9224]

@@zmurray9499 mines is like the fleet vehicle/ caterpillar/ school bus yellow. Think it's called wheatland but I have not seen very many at all.

[@elcaminosupersport]

I haven't tried changing out switches yet. I would tied a string at end of each plug before pulling out once out tie it to new plug to pull back down

[@LinusScrubTips]

I’m having the opposite problem. I can’t find a non intermittent switch for my Comanche. I’m thinking a CK one might work.

[@Eatcrap00]

Good video sir I think I know why I have no reverse lights on my k5

[@fixnshet5640]

Electrical goes nuts when i turn the wheel… hope that the multifunction switch (white part with the wires) fixes it

[@zmurray9499]

@@fixnshet5640 I probably say it's something to do with the wires running through your steering column. The switch, jiggle it around without moving the wires going up your steering column

[@crsmith56]

If you had to do it again, do you think it would have been easier to remove the entire column out of the truck and then replaced everything?

[@zmurray9499]

@@crsmith56 no!!!! Just make sure you either take a picture with your phone inside the ignition tumbler hole. So you can see what the orientation is with the teeth on the ignition rod. And don't buy the cheap ignition switch. It would be very easy for me to do it a second time. Struggled the first time because I didn't do those two things👆🏼.

[@zmurray9499]

@@crsmith56 it would be easier but inot necessary

[@charlessalard4636]

How you mess. It up easy way???

[@charlessalard4636]

Took me 8 hours

[@charlessalard4636]

My steering lock don't work now..???¿?

[@charlessalard4636]

It 100% suck trying to adjust it..never again

[@zmurray9499]

@@charlessalard4636 well hopefully you don't have to do it ever again🤷🏼‍♂️... took me quite a while to figure out the orientation because I did not look inside the lock cylinder hole before taking it apart...

[@charlessalard4636]

@zmurray9499 does the sprocket come out?? Saw a video somewhere where they put it on key cylinder and put it in???

[@fixnshet5640]

Dogs a goooooboi