1967-72 Chevy & GMC Truck Turn Signal Switch Install / Tilt or Standard Column

[@davidfield8069]

Dave is the best at showing the process for servicing the 67 -72 Chev. Trucks.

[@brianswimmer]

Thank you. Now just come on over and show me in person. My truck is ready. I'll have the beer and food ready! Thanks

[@BROTHERSTruckPartsTV]

Sounds like a BBQ and work on the truck day!

[@brettburwell1218]

18:20 forgot turn signal switch lol great video I did the same thing put my wheel on and forgot it

[@BROTHERSTruckPartsTV]

Ha, we actually shot this over without the mess up and apparently it got lost in the editing. Looks like we'll need to go back and fix it! Thanks for the heads up!

[@sportriderseattle]

@@BROTHERSTruckPartsTV yes please. that turn signal canceler is a bizarre thing. I installed a new column, and the canceler worked perfect for a day, then mysteriously stopped in both LT and RT

[@timszal5291]

When does he take the dash apart to get all the screws out that fell down the defrost holes?

[@thetasteofluck]

KEEP UP THE GOOD WORK!!!

[@h.i.sc-10tips31]

Yes sir

[@francfurian8215]

Good one Dave Cheers

[@thomaswhite3831]

If you tape your new wires, to your grey wire, you can use it to pull the other wires through the column cover .

[@CKID-dv8tq]

Great video I had a similar issue months ago when I put a 15 inch steering wheel in my truck but I cleaned the horn ring and my horn worked again

[@BROTHERSTruckPartsTV]

RIGHT ON!

[@h.i.sc-10tips31]

I replaced my turn signal and now my horn wont work

[@robertemmons2260]

Yep. Done this twice now. Shee-Mar products use to be top-notch, but are now substandard. I'll have to look into the Brothers Trucks line and check out the quality of their product.

[@keithbrann5086]

16:15 definitely a Bob Ross vibe going on there

[@BROTHERSTruckPartsTV]

LOL

[@marksheffer625]

Thanks David appreciate all your work. Would this be a similar process for a 64 chevy pickup

[@BROTHERSTruckPartsTV]

Yes, basically the same. Thanks for watching!

[@csfive03]

Do you know where we can find and purchase that copper contact ring for the horn?

[@anthonymilone7243]

Hi Dave great video by the way it helped me install a new turn signal switch, I did have a problem , driving with the headlights on and apply the turn signal both turn signal lights flash on the dash only , both front and rear work as they should, any advise on what that may be. Thanks Dave keep up what your doing. Anthony

[@ORipples]

Awesome video! I have a problem with my blinkers and am not sure if I need to change this or not. My left blinker works perfectly normal. My right blinker works until the brakes are applied. When I apply the brakes it goes solid like a brake light. Could it be this blinker switch because it is pretty dirty in there. I cleaned it as best I could but it’s possible that it’s burned yes? Other than that I believe it would be a ground that’s corroded or something like that. I need some help lol

[@BROTHERSTruckPartsTV]

Provide a proper ground to the housing that's giving you trouble and see what happens first. If that doesn't fix it then move on to the switch. It's probably a ground problem.

[@ORipples]

@@BROTHERSTruckPartsTV man thank you so much. You have no idea how much I appreciate it!

[@rauljrlara9994]

If I have the 1964 chevy c10 wiring harness installed (updated version) , but have a 1968 chevy truck steering column , do u think it'll be compatible

[@artm700_]

Got a similar problem on my 79 c10, left blinker works but when I turn the signal up for the right turn signal there’s no click or anything, perhaps something is broken inside the steering column? Please help thanks

[@DEADIKATED]

I have installed a new wire harness from the under the bed to the tail lights everything was working but left brake light I was researching and read this might solve the problem any ideas?

[@marioneta1149]

I Hear you Pa’ !

[@armygreenfj3924]

Hey Dave, so today I notice that my front side markers turn on when I press the brake. Any idea what it could be?

[@qball1of1]

Can these wires which have the correct horseshoe plug be used in the stock style repro tilt columns? The big flat blade that need an adapter aren't my favorite setup..

[@armygreenfj3924]

You mind re doing all your videos but with my K5 blazer lol. I need to replace some parts 😂

[@chevylandt.v]

Thanks for the video I might have to do this to my 70. Is it hard to do a auto transmission swap over to a manual transmission?

[@BROTHERSTruckPartsTV]

It's definitely not as easy as it would be going from manual to auto, but it's doable. The pedal assembly and clutch linkage will be the most difficult part.

[@chevylandt.v]

@@BROTHERSTruckPartsTV oh ok thanks for the info.

[@h.i.sc-10tips31]

This swap is getting more common

[@h.i.sc-10tips31]

@@chevylandt.v go for it

[@chevylandt.v]

@@h.i.sc-10tips31 I just might have too thanks.

[@RodriguezHugo]

Do you have a part number for the last spring you added?

[@BROTHERSTruckPartsTV]

We do not carry that spring. If you need one your best option is to gran one from a junkyard.

[@RodriguezHugo]

@@BROTHERSTruckPartsTV Ok thank you and appreciate all your videos.

[@michaelanthonyortegaherrer348]

I bought my starter switch all the wires are connected how do I slide the plastic piece in where the wires are connected 🤔

[@BROTHERSTruckPartsTV]

you slide the wires into the plastic plug first, then on to the switch.

[@shawnlawrence4840]

Dave, I wish to make my cucv a dual tank, all I have is the 2nd tank, also the fuel gate for the fleet side, even though it would be a conversion from the driver side to the passenger side off a discarded fleet side. What would I need to make dual tank possible

[@BROTHERSTruckPartsTV]

Shawn, we'd be hard pressed to give you a complete answer here on our channel. Please call our shop and one of our techs will guide you through this.

[@steveb7311]

Excellent, excellent, excellent video. My plastic casing around my spring loaded horn contact on the turn signal switch broke, so my horn did not work. This video is an excellent guide, and I'm glad I watched it before re-assembly. I did not realize one of the three screws was shorter. And great call on rotating your screw pattern on re-assembly so the fitted plastic doesn't crack on your new part. The only two things that I would add is that 1) the spring loaded contact may differ on some kits, and the kit directions tell you how to reconfigure it so it works; and 2) most turn signal switch wiring harnesses are already plugged into the strip terminal. Here is a video on how to unplug the wires from the strip, using an eyeglass repair kit (good info starts at about 2:00).... kzbin.info/www/bejne/nGPMc6CFj7NmnZY

[@rockyp544]

I know this is relevant to this video, but have you made a video on leaf springs to trailing arm conversion?

[@BROTHERSTruckPartsTV]

Not yet. One of the guys at our shop recently did the conversion to his truck, and we're waiting to gather some impressions of the kit, function, ride etc before we make a vid.

[@rockyp544]

@@BROTHERSTruckPartsTV thanks for the reply. Looking forward to it when and if you make one.

[@sammyarmstrong2098]

Does this cover 60-62 or are their other facts I need to know?

[@BROTHERSTruckPartsTV]

60-62 is slightly different, although most of the tips here could help you get through that job. We'll look into doing a Video for 60-62.

[@johnvickers6280]

U all have a lot of great videos do you guys ever work on 80 models Square body

[@spud4ever290]

Dave does put out good videos !

[@BROTHERSTruckPartsTV]

Yes we do

[@1Patient]

I almost bought one of these trucks, until I got inside and sat in it. I quickly realized that they had built the Gas Tank into the Cab of the truck, also, when I went from the Gas to the Break, my Knee kept hitting the steering wheel... I'm like, nope, not buying it.

[@esmundolarajr3049]

Does a 68 come with that bulb?

[@BROTHERSTruckPartsTV]

The bulb for the indicator?

[@esmundolarajr3049]

@@BROTHERSTruckPartsTV yes

[@BROTHERSTruckPartsTV]

@@esmundolarajr3049 If it's a Non-Tilt then it uses fiber optics and doesn't need a bulb, if it is Tilt then it comes with the bulb.

[@h.i.sc-10tips31]

@@esmundolarajr3049 what size of bulb is it

[@esmundolarajr3049]

@@h.i.sc-10tips31 The 68 with a non tilt doesn't have a bulb. It has a fiber optic cable. I think one end goes to a bulb in your gauge cluster and the other goes to the indicator.

[@tmsnyder1971]

should pull a wire or string through while pulling the old wires out, then use it to pull the new wires in

[@GMZee559]

My 74 doesn’t have a gray wire 🤔

[@charleslawson6377]

What if wire colors dont match

[@nathanirvin3081]

wait where does that grey wire go? that's the part I need lol

[@BROTHERSTruckPartsTV]

The grey wire is for the indicator lamp on top of the steering column.

[@johnalbritton1044]

I have '50 chevy. can you do turn signal add on video?

[@BROTHERSTruckPartsTV]

Great suggestion! We'll look into it.

[@kenlelon369]

you California boys like to - Go Ahead - and do things a lot! Well, go ahead.

[@imabuzzard1]

you're working way too hard. The turn signal assembly can be repaired unless the nylon is cracked where the turn signal stem attaches. You do need to remove the housing under the dash. Also remove the horseshoe bracket from the column. No need to cut any wires as they all will easily feed through the column. To back off the assembly just use a screwdriver in the hazard hole and pry out.

[@DEADIKATED]

Can make a video? I have this problem mow