Start stop station motor control , 3 motors sequence start with two timers OMRON on delay.

[@leondioquino4241]

Thank you sir for these motor control with timers, Installed two motor with one timer master working good. Good bless you master 👍

[@tmelectricaltutorials2851]

Thank you 🙏

[@bonnylasu7665]

Wow 😮 ! Sir very interesting. Thanks for your video teaching of electrical installation for future carrier.

[@khangezilemthethwa1926]

Thank sir for your lecture. It has help me and I’ll keep on revising it. Please do more similar videos. Thank you very much.👍🏽👍🏽👍🏽

[@tmelectricaltutorials2851]

Your welcome bro yes i have more videos I already downloaded you can watch and still im doing more videos.

[@danielbartolome8807]

Ayus mga tutorials nyo po master complete details daming kung natutunan maraming salamat po sir🙏

[@tmelectricaltutorials2851]

Welcome bro

[@musengekapoma576]

Very educative thanks from mother Zambia 🇿🇲🇿🇲🇿🇲

[@tmelectricaltutorials2851]

Thank you 🙏

[@bonnylasu7665]

Thank you sir, I'm very interested teaching about your electrical installation . I'm really bit happy because I have an bit idea about your teaching of electrical installation for my future e.

[@tmelectricaltutorials2851]

thank you so much

[@victordelacruz4906]

Thanks for sharing this video malakeng tulong to pra samin sir

[@tmelectricaltutorials2851]

You’re welcome bro

[@leahsantos5289]

Nice tutorials professor very helpful ❤️👍

[@tmelectricaltutorials2851]

Thanks 🙏

[@owinookello9358]

good visldeos mr terry

[@tmelectricaltutorials2851]

Thank you mr Owino

[@cdalisayvlog9811]

Thanks master for sharing these video

[@bonnylasu7665]

Sir, the 3 motors control circuit is parallel connection or circuit?

[@tmelectricaltutorials2851]

yes motor supply must be parrallel connection. control circuit is important to learn instructions

[@tadiosnyamuziwa5679]

Thank you Master for the informative video. Is there a problem if I run motor #3 using aux m1 instead of aux m2?

[@tmelectricaltutorials2851]

No problem but its not a proper way.

[@tadiosnyamuziwa5679]

Alright

[@AschalewTesfaye-h6q]

thanks! will show us during star delta motor connection how to slow and fast the speed without vdf

[@bonnylasu7665]

. Wow! Very interesting about your electrical installation teaching of u tube. Can explain how to wire 3phase air compressor auto on off with face failure

[@tmelectricaltutorials2851]

thank you for your nice comment bro you can learn electrical and wiring installation this channel,if you use timer then on and off operate

[@bonnylasu7665]

Hi sir, I'm very interesting about your video teaching of electrical installation. For 3 motors starter control, can U connect indicator lights?

[@tmelectricaltutorials2851]

yes should every one motor have one indicator lights to idinttify the M1 to M3 running.

[@michaeladdisu8043]

thanks brother , helps alot

[@tg9507]

Very informative video. Can U pls help me with following task?. I’m a woodworking guy, and a novice in electrical automation. I am trying to automate my shop dust collector filter cleaning system. I have a single phase 2kw 220V shop vac, and a small low RPM 200W motor that runs the dust collector filter cleaner. I start and stop the dust collector with a remote controller. Today I run the dust collector filter cleaner via a separate remote controller. I would however want it to start automatically 10 sec after shut down of the dust collector and run for 10-15 sec before it shuts down. This repeats after each time I use the dust collector. Can you guide me on combining relays and timers, or better still, could I ask you to create a KZbin video on this topic, as I am sure I am not the only one struggling with this task.

[@tmelectricaltutorials2851]

Bro I have already uploaded a vedio related to your request. Please watch the omron twin timer automatic on/off operation for motor control vedio

[@HtunMyat-o1b]

Thanks a lot.

[@tmelectricaltutorials2851]

Most welcome!

[@syedhassnainali2917]

Sir, please tell me if we need 8 motors run just one after another as you told in this video but timer not required jut interlocking with 8 pin relay so, is it possible?

[@tmelectricaltutorials2851]

watch my one video 4 motors interlocking motors and you can additional more motors even more than 8 motors just follow same connections.

[@boybravo689]

Sit ask ko lng dual time po ba yan ginamit nyo lng ung on delay feature nya tnx po

[@tmelectricaltutorials2851]

Dalawang timer ginamit ko na on delay para sa dalawang motor.

[@tmelectricaltutorials2851]

Bro iba yung model ng dual timer , ang dual timer ang function nun ay, on delay and off delay. Ibig sabihin auto start and auto stop depende kung ilang minutes bago mg start at stop na gusto mo, din start uli continuous ng ganun.

[@boybravo689]

Sir watching for the second time sir pansin ko walang tagging sa normally open contact ng timer relay di malaman kng anong timer belong yong mga auxilliary contact sir

[@tmelectricaltutorials2851]

Meron naman bro

[@ghassanalniser3261]

🤔🤔🤔😕😕😕

[@ghassanalniser3261]

Watch channel Edo Galung Explains electrical circuits very well

[@avelonestoesta6128]

Mas maganda po pag tagalog nlang po

[@tmelectricaltutorials2851]

avelon, gusto ko sana tagalog kaso daming akung subscribers kase na ibang lahe.

[@avelonestoesta6128]

@@tmelectricaltutorials2851 ,ganun po b sir..slamat

[@tmelectricaltutorials2851]

@@avelonestoesta6128 ung unang ginawa kung video sinabihan ako na eglish ko nlang daw pra maintinidihqn din nila, copy mo ung Diagram un ang importante idol. practice mo madali lang yan. Bayaan mo pag marunong na ko gumawa mg english subtitle tagalog ko nlang mga videos ko. Para maraming makaintindi. Thanks

[@avelonestoesta6128]

@@tmelectricaltutorials2851 ,pneumatic at hydraulic sir gawa ka sin po ng tutorial

[@tmelectricaltutorials2851]

@@avelonestoesta6128 cge gawa ako nun automation machine yun idol kelangan start muna ang hydraulic pump bago mpaandar ibang motor my pressure switch un na normally open.