BECKETT OIL BURNER WILL NOT RUN merch = teespring.com/stores/steve-lav / stevenlavimoniere lavimoniere productions llc subscribe to my channel / @stevenlavimoniere lavimoniereplumbingandheating....
Пікірлер: 68
@WeatherNut276 ай бұрын
You know what I havent seen Steve use in a long time? The Draft tool
@drohvac45836 ай бұрын
Yea, I wonder why?
@WeatherNut276 ай бұрын
@drohvac4583 Maybe it deteriorated in the oil tool box. Lol
@theodorgiosan25706 ай бұрын
@@WeatherNut27I have one of the ancient clear Dwyer ones with the ball that gets sucked up the tube. Still works probably 40 years after it was made. Probably not super accurate but good enough. Still have a Bacharach Wet Kit too, one of the glass ones , that still works too but don't use it as often as the Testo 310.
@hondamxbmx6926 ай бұрын
I love the comments while talking to customers. “Dependable degrees! Wtf you talkin about” 😂
@semajd59956 ай бұрын
I love how he always ignores what the person is talking about to speak about the job then randomly pulls them back in by going back to their topic.
@Fred-xo3ku6 ай бұрын
The brutal winters 🥶 of Massachusetts. Steve is a lifesaver. 👍
@porky77536 ай бұрын
Steven, i had a paper route too. I hated Sunday mornings with the ad inserts. We had a good childhood and that's where we learned our work ethic.
@tonym69206 ай бұрын
Hey Steve and Miss Molly! Workin’ again ya’ll. 👍👍
@MacMcCabe24566 ай бұрын
Steve you are the man. Down to Earth and real. Good job once again !
@zekenzy64866 ай бұрын
Great Video as always. Thank you for sharing. Have a nice weekend
@webmastercaribou75706 ай бұрын
Nice, I haven't worked on those in decades. I installed a minisplit two years ago. Even at 18 degrees, my burner rarely kicks on. Mostly just for hot water.
@lindajames50656 ай бұрын
Hello Steve and Miss Molly 😃👍🏻Stay warm 👍🏻 Texas Lady
@sokola3116 ай бұрын
Hey Steve I finally ordered a "She's a leaker Momma!" t-shirt. Classic.
@tobysarsi68646 ай бұрын
Steve and the customer have the same sounding voices-As if they could be brothers 😂
@williamdyckman97046 ай бұрын
You are a god send in this brutal cold !!
@dosgos6 ай бұрын
Fuel savings from smaller nozzle & tune up will pay off in a few weeks. Awesome service.
@Hvac-dude6 ай бұрын
I just did some service work today !!!!!
@Garth20116 ай бұрын
Regarding finding help these days, you probably can find help, employees however, they usually require some basic training in the trade or type of job you give them. Many of them are still learning how to show up for work on time and be productive.
@zackmax71846 ай бұрын
They are Showing Frank Perdue on T V again. He used to feed the Chickens Merigolds to make their beaks and feet more Yellow when We used to grow for Him.
@edbonjovi91336 ай бұрын
Hello Steve from. Leak master plumbing in ct
@robertmilne3256 ай бұрын
Beckett has always introduced little " improvements" like that clutch coupling. Remember the air funnels they tried years ago. Not worth 5 cents. Rob, Nova Scotia
@Joop50006 ай бұрын
Hey Steve, Why don't we see the Testo analyzer anymore?
@dock_yard11496 ай бұрын
And the ancient draft meter.
@ClickinChicken6 ай бұрын
Doctor of the oil burner, Steve L. HA! Mucho Admiro.
@Farmerdubs1016 ай бұрын
Great video Steve. Do you guys have propane and natural gas furnaces? In Ontario its very rare to see an oil furnace. It’s mostly natural gas or propane
@user-sx2xy8dn9v6 ай бұрын
Kick ass video Steve, stay warm and keep the videos coming 👍 👌 ☝️ 🫵! Yo Steve how about a cooking video anytime soon?
@tomdale13136 ай бұрын
"GUNSLINGER FOR HIRE", thxs for sharing...
@westbygodvirginia5556 ай бұрын
Good stuff
@joeyjennings95486 ай бұрын
.75 90° nozzle? straight coupling sounds way better. working good now 👍
@iamnoone.6 ай бұрын
Howdy Steve and Molly
@mjg2636 ай бұрын
I don’t understand the point of the clutch coupler, what’s it supposed to improve over a simple pump coupler?
@semajd59956 ай бұрын
Hey Steve…got a Carlin burner…got apart got great oil flow but every couple days won’t fire
@rodneyskinner77416 ай бұрын
Hello Steve!
@dylandepuy37156 ай бұрын
Can you do a video just on your gripes with the bio slime? An in-depth video with your thoughts on it would be interesting
@theodorgiosan25706 ай бұрын
It's because the old cloth filters aren't fine enough. They have spin on filters specifically rated for biofuel that deal with the issue. In my opinion they should all be changed to spin ons at this point. Can't filter water and junk through a piece of wool. Even better the spin on filter mounts can fit a Caterpillar 175-2949 water separator. Same thread size as the heating spin ons but pulls water out. Best way to set it up is 2 pipe system through a water separator. That way it keeps the water from sitting in the bottom of the tank because the oil burner pulls all the oil through the water separator and puts the clean oil back in the tank.
@eugenkaranxha16596 ай бұрын
I have been bombarded with service calls had to replace an inducer motor last night after the tenants had no heat for a few days no plumbing supply store had that for that particular furnace I had to order it online after I told the owner 6 months ago I replaced a flame sensor on it I released the inducer fan was getting stuck I lubed it I told him needs to be replaced because it will fail at the worst time and it did on the coldest days sometimes they have to learn the hard way
@dock_yard11496 ай бұрын
I think Steve found 3 successive causes of the guy’s problems in less than 5 min.
@DAS-Videos6 ай бұрын
Oh my gosh I can even see how bad those electrodes are placed. The oil won't ignite from the spark that is an inch away.
@huejassle30196 ай бұрын
Hey steve, any insight on a no green light blinking or turning on what so ever..tried holding for a minute plus and no luck. Recently changed the auto valves and expansion tank. I got pressure, no air, water flowing. But it wont even turn over for 2 days now..i live in alaska and do it my self but i cant seem to figure this one out. Thanks🙏🏽
@deanguando13356 ай бұрын
He was running a very large nozzle in that Beckett unit.
@dock_yard11496 ай бұрын
Yeah that was the definite cause. Or it was the electrodes. Or the CAD cell. Or the clutch.
@bobsmith11016 ай бұрын
What pressure scale on the pump, PSI? Good vid Lav.
@biker555556 ай бұрын
Yes, PSI, he has videos on the oil guns and their pumps if you wish to learn.
@acrservicesmathewr75656 ай бұрын
Typically 140. It will say it on the burner what factory it’s set to
@dje-slick68906 ай бұрын
Fucken house could catch on fire....WITHOUT A PRO...!
@steze486 ай бұрын
Now I know how to pronounce your last name Steve.
@Garth20116 ай бұрын
That big orifice nozzle the customer put in was WAY TOO RICH and likely was consuming much fuel for the short time he had it. You have to wonder who sold him that size if he didn't buy it on his own. The fact that the fuel pressure was that low tells me the unit hasn't had a decent service job in a while.
@DAS-Videos6 ай бұрын
That cad cell was shot.
@jasongeo26 ай бұрын
Steven I been wanting to ask you, I noticed on several videos with Ms Molley. And on some videos I noticed her hanging out in the driver's seat hanging out the window to greet you as you retrieve a part or something. Have you ever thought maybe an eagle or other bird of prey can swoop down and take her? I would be concerned was wondering on your thoughts?
@JohnR99656 ай бұрын
Can I have what your on? Must be pretty good stuff….😂😂
@biker555556 ай бұрын
No reason to be concerned, she only looks innocent! She is a SWAT trained and can fend for herself against any enemy of the sky.
@user-sx2xy8dn9v6 ай бұрын
What an interesting question 🤔
@japmlp096 ай бұрын
Go away lib..
@jasongeo26 ай бұрын
@@user-sx2xy8dn9v it is. Hopefully get some feedback from Steve
@paulroggemann10176 ай бұрын
he got BOTH BARRELLS
@memyselfandifarmer6 ай бұрын
That’s the problem “”””’””””””””””””””?
@sknight03916 ай бұрын
💪😎👍
@bruceorourke54326 ай бұрын
No smoke in draft
@dosgos6 ай бұрын
Joe Homeowner!
@jayclark59126 ай бұрын
I watch too much...I said cad cell too. We will see I guess.
@dje-slick68906 ай бұрын
Never let your customers do their own shit...TELL THEM SIMPLY TO CALL FOR SERVICE !! As a tech.....you make more money that way !
@biker555556 ай бұрын
Steve is not money hungry. I always give people an option to do their own shit because they will with or without me if they have enough will. People that are willing to pay will call you regardless. Doing own minor service is not rocket science, one just needs to put enough effort into learning the right way. The problem today is people are not willing to invest enough time and effort to learn, they make shit up as they go and make mistakes. Read the darn manual! RTFM
@paulpark58146 ай бұрын
Sir could you be quiet and just leave me to work dear god
@michaellee6956 ай бұрын
Steve, the oil companies refer to that slime in the filters as BidenSlime.
@iandrew63476 ай бұрын
Hi 🫶🏻🇬🇧🫶🏻
@Deion2456 ай бұрын
1st
@oantech42526 ай бұрын
Nice job Steve.. I love the Beckett videos. This is a good customer. The last guy (electric heat guy) was a lib-tard fool..