Could try heating the blob chip from the back to re-flow the solder connections, worth a try.
@murraymadness46743 ай бұрын
good idea, does it ever work?
@tadasrimkus35453 ай бұрын
was about to comment that
@EgoChip3 ай бұрын
@@murraymadness4674 Only one way to find out.
@j.f.christ84213 ай бұрын
Won't work, they're wire bonded (like normal ICs), not soldered like BGAs.
@mattinwinkymg3 ай бұрын
@@j.f.christ8421 still worth a shot though
@quiddity19773 ай бұрын
I'm FINALLY famous! In the same video as Dave! Haha Thanks for trying Steve. I'd have loved to have seen it working as it seems a usa exclusive one. Knew I should have got 2 of them instead of an among us figure for my nephew! Cheers again, Stuart.
@Anderyo3 ай бұрын
You are not famous
@unachemaxwell3 ай бұрын
Nice to see you! Get a picture with Dave and you will level up :)
@rorychivers87693 ай бұрын
@@Anderyo I know him now. Are you jealous of his fame?
@quiddity19773 ай бұрын
@@Anderyo aren't you a treat?
@jylam_3 ай бұрын
NOOOOOO, the spoiler !
@williamgreen55753 ай бұрын
While pressing the 'blob chip' you were also flexing the board. May be broken traces.
@flickpad3 ай бұрын
I was thinking the same. There was a particular joint above the chip that was moving a LOT. Might be worth investigation
@chrisj28483 ай бұрын
Congratulations on rolling over the counter Steve. I like your solution to the 100's. 😅👍
@StezStixFix3 ай бұрын
😂 thanks Chris!
@Maxwelllewis923 ай бұрын
Hey, Steve, I think the LCD connector was on the board opposite the blob, could there be a bad connection on the connector, and pressing the blob manipulates it?
@TheSCSIBug3 ай бұрын
Really appreciate you sharing the successes as well as the failures, Steve! Too many KZbinrs only show their successes & conceal the real challenge of DIY repair. It's especially important in these days of anti-right-to-repair efforts on the part of the corps.
@psylencecy3 ай бұрын
come on Steve do it! for the content baby!!
@ScottMadeAThing3 ай бұрын
Yay, I'm so proud of the counter! It always the first place I look when your videos load up haha. Also, looks like you need to update the other counter and add another 1k! [Hidden down here so not to reveal video spoiler] Stupid blobs. I wonder if maybe a leg of the IC under the blob wasn't soldered well and then the blob stuff got in under a leg or two, preventing contact. Then when you're applying pressure, you're connecting one of the legs but maybe another leg has too much blob under it for pressure to resolve? Shame its so hard to remove blob. BTW, speaking of Dave, you wouldn't believe it but I was repairing a TOMY Super Cup football game (video 'soon') and guess what fell out of the box? A DAVE. I was going to call him Steve and put him in resin, but there's a fine line between imitation and tribute so I gave him a proper burial.
@StezStixFix3 ай бұрын
😂 Dave 2! Love it. Yeah, I might still try and remove that blob. I've been told you can melt it off with some chemically stuff or something. Sounds like hard work though! 😅
@PollokPoochesDogWalking3 ай бұрын
@@StezStixFixI'd be well up for watching a video of you melting a blob off!!
@hapskie3 ай бұрын
Thank you for hiding spoiler information, wish everyone would do that!
@iaincowell97473 ай бұрын
@@StezStixFix Try a heat gun to soften it first. From what i've heard about the chemical way, it takes harsh and nasty chemicals that you definitely don't want to be breathing in (some can also damage the board)
@j.f.christ84213 ай бұрын
@@iaincowell9747 You can't get the epoxy off without causing damage.
@memoryman84623 ай бұрын
I always wonder, do people get there items back when they send them in? Or are they alway making a one way trip?
@janskeet13823 ай бұрын
Well done darling. You publish all your stuff, even if it doesn’t work and also, you turn up in your work like an artist. You are a lovely man. Blessed be 💕
@Simon-xc5oy3 ай бұрын
Blessed be?? The Hooded Man shall come to the forest....To be Herne's son and do his bidding.....
@janskeet13823 ай бұрын
@@Simon-xc5oy Prophecies of Gildas
@Simon-xc5oy3 ай бұрын
@@janskeet1382 Ahhh.....its an old English Pagan greeting so being a child / teen of the 80s I was taken back to Richard Carpenters Robin of Sherwood....a true classic. No clue about Prophesies of Gildas....sorry....
@janskeet13823 ай бұрын
@@Simon-xc5oy Yes, I’m an old English Pagen. The Prophesies of Gildas are quoted in Carpenter’s Robin of Sherwood.
@Simon-xc5oy3 ай бұрын
@@janskeet1382 Ahh I see. Just know it as Pagan etc and through Robin of Sherwood. It all seems a long time ago now..since the 80s and such great television....Most of the cast are in their 60s and 70s now...how time flies.
@rutski51503 ай бұрын
This might just be me but I think when pressed the board seemed to bend along a distinct line under the blob chip, is it the board itself?
@waynejohnson15003 ай бұрын
Thought the same. Maybe broken lines?
@OneHundredEnvelopes3 ай бұрын
something stupid that i found interesting regarding the blue mat, the circular indentation to the right of Dave is to hold a loupe! I saw this on one of My Mate Vince's videos.
@plan7a3 ай бұрын
Alternative Comment: Bob, The Builder: 'Can we fix it?'. Steve: 'Well, we can try!'.
@zKaltern3 ай бұрын
Blobby Blobby Blobby!!! (Only those in the UK of a ... certain age will have any idea what that was...!)
@StezStixFix3 ай бұрын
😂 bring back mr blobby!
@shneeblee1803 ай бұрын
Please don't 😂
@matthewlofthouse40283 ай бұрын
No for the love of God don't use too give me nightmares 😂
@alienfish85213 ай бұрын
Oh yeah we all know.
@MaxStax13 ай бұрын
I'm from the U.S but i learned about Mr. Blobby from an episode of Expedition Theme Park on KZbin.
@speedwaynutt3 ай бұрын
Guess in this Jurassic Park it wasn’t Meteors that wiped out the dinosaurs it was instead the deadly Black Blop.
@GODCONVOYPRIME3 ай бұрын
You know Dr. Meddows suggested the same thing in the 1988 version of the BLOB. Small world isn't it?
@plan7a3 ай бұрын
Silly idea but something worth trying? Maybe the screen is coming on but may not do anything unless you press a button on the remote? Will it get anything (a signal?) from the remote? I'd assume the 'white' object is a receiver for this. If that isn't working maybe it's causing the rest of the board to fail? I'm sure it isn't but something is awry somewhere there, so what else could it be? (Sillier idea, try different batteries, alkaline instead of whatever else?). Further idea - also, perhaps silly, try to see if the screen is properly connected, it could have a loose part on the ribbon cable?
@coondogtheman3 ай бұрын
I have four of these tiny TVs mine are Original batman, back to the future, south park and friends. The remote died on the south park one but the TV still works. I'm curious if you take out that 8 pin rectangular chip which holds the videos that are shown and put it into another one of these TVs. I'm also curious if it's possible to extract the video files and play them back in VLC on a PC
@kilosierraalpha3 ай бұрын
It's almost never the blob chip that fails. The most likely culprit is the screen.
@chooky78143 ай бұрын
Hi from Australia.. i really like watching u have a go at fixing stuff.. i stumbled across your channel by accident and love it!! Im a 50 yr old female who isnt into this stuff but for some reason find this realy interesting and have a chuckle at the little jokes u make.. keep up the great work!
@Johadart3 ай бұрын
I’m over the moon with your 107 days since melting plastic, don’t be so quick to blame it after this video, your doing a swell job steve, just remember Dave is you helper, not vice versa. Lol keep up the great videos mate. 🤙🏼🇦🇺 Joe from Australia 🤙🏼🇦🇺
@BambiHI073 ай бұрын
I really hoped this was going to be a fix! I know you can find the videos of the Jurassic Park tv' on YT but, it would have been interesting to see you pull them off the flash chip. (I've done it from a couple of old toys with screens) It's definitely worth learning how to do!
@markshellard58943 ай бұрын
Thats the tv thing from willow the wisp
@ericpode60953 ай бұрын
Evil Edna! 📺😅
@johnfbayley3 ай бұрын
While I honestly don’t like to see you fail it’s comforting to know you do ! Love the videos .
@GadgetUK1643 ай бұрын
I really love what you've done with the channel! So much character!
@davidrobertson57003 ай бұрын
When he said Dave, he meant me
@summerlaverdure3 ай бұрын
can't fix em all, oh well. still cool to see inside it, great video!
@TheMadSqu3 ай бұрын
That was a killer cover of Duran Duran!
@braddl94422 ай бұрын
I have one of these for back to the future.
@Boogie_the_cat3 ай бұрын
I dunno, this looks a little too "adult" for me. My LeapFrog tablet has pictures of animals, and when i push the "cow" button, it moo's I feel like a big man with my LeapFrog tablet. You with your Steam Decks are playing baby crap.
@littletommy163 ай бұрын
Try it, it's not working anyways. And, someone needs to figure out a fix for the blob chips. Seems to be a consistent issue.
@j.f.christ84213 ай бұрын
Fixing them is easy if you have the equipment, which of course no-one can afford. And even then no-one has a good method of removing the epoxy without doing damage, it's pretty tough stuff.
@DavidPlass3 ай бұрын
Bond. Wires Bond. Nice Duran Duran-like outro. :)
@jamielishbrook23842 ай бұрын
They made a South Park version of this. I saw it in the toy department at Walmart next to the Legos one day. Let that sink in.
@FixDaily3 ай бұрын
It doesn't matter at this point but when you have buttons, you can test the voltage drop across a button, so you can analyze if when you press it the voltage goes out. Usually the buttons are pulled up by a resistor or internally of a MCU.
@JonnyFix3 ай бұрын
The board did flex a lot and the blob is quite firm so I don't know you'd actually move anything under the blob but certainly the board flex could be affecting any poor solder joints on other components. Check none of the buttons are stuck on in case that is and stops it booting?
@simonperry85693 ай бұрын
You need to rewire the flux capacitor and re-solder the quantum blob chip. Then pretend your Jeff Goldblum and it should all work fine. Stupid dinosaur thingy…
@kingforaday87253 ай бұрын
This is a very common problem with these lil TV's...........whatever the problem is.
@maico49023 ай бұрын
Hello Mr fix and dave I have a cctv camera it was working fine then just stopped it is wifi and blue tooth and cost £60 from aliexpress it works with the smartlife or tuya app but I couldn't get it to work Would you like it for your channel maybe have a try at fixing it Or just have it for parts
@beatmastacheese38872 ай бұрын
I swear dude be dropping some dope ass sound you need to make a album
@wanjockey3 ай бұрын
Good E for Effort
@qdukez2 ай бұрын
1st time watching your videos, was caught off guard with the bars, good stuff 💯
@t0nito3 ай бұрын
Did they forget to solder in an eprom or something? There's a vacant spot for a chip
@coreybennit91973 ай бұрын
hey mate, I am in west australia, i have a psp1000 that has a problem with the back light for the screen, ive replaced the screen, and tried a small yt fix but got nowhere, would you be interested in looking at it?
@peatmoss44153 ай бұрын
S1 is a Switch the S stands for "S"witch. Forrest Mims' books has all that elementary info....
@djttster3 ай бұрын
Now i’ve seen your address i know why your accent sounds so familiar. I’m a dutch guy, but my dad is from Bury…
@andytipping703 ай бұрын
how about adding a ton of flux then reflowing said blob chip? you cand exactly make it any worse right?
@GawrGurasBathTubPizzaАй бұрын
so no racism calling it cheap chinese crap when its not a clone of something? because everything is chinese even iphones
@atheistdingo62733 ай бұрын
Mate, the blue mat only costs about 10-20pounds. Time to freshen up.
@portland-1823 ай бұрын
Have you tried using the remote control? As with some 'real' TVs 'on' means standby. You need to use the remote to turn it on...
@NHLroyrocksАй бұрын
you should have opened that blob up! It doesn't work anyways. You could have shown us why you dont open a blob chip
@garymucher40823 ай бұрын
I would absolutely remove the blob and see what else is under it. Could be a standard processor that has a few unsoldered leads. I mean it is broken presently. What else could you possibly do to it...
@309electronics53 ай бұрын
The blob is the cheapest way of producing a chip. A raw semiconductor dice which has no package (and is likely a APPLICATION SPECIFIC IC OR ASIC) and its glued to the board and has gold wires welded from the tiny mm size pads on the dice to the board. Covered by epoxy to protect it from light and rev engineering. Because you dont need metal pins and a package it saves a few cents
@RJAH355Ай бұрын
Didn’t know you lived in bolton my home town to. Have you ever tried to fix a car key. Would pay for your time.
@erickelly8704Ай бұрын
Ok isn’t it a safety switch in the back so when the batteries are being replaced the TV won’t come on from the back in the right hand corner?
@cputecch2 ай бұрын
I agree you should’ve heated the blob ship up. I see if you can reconnect the saddle joints.
@mrsiborg2 ай бұрын
Mr Blobby strikes again.
@ucitymetalhead2 ай бұрын
I tried taking mine apart it was the friends variant and I was bummed that I couldn't add my own movies.
@MrJozza653 ай бұрын
Stupid Blob Chip
@Denise_in_progress3 ай бұрын
Maybe the nand chip has corrupt software... try to find software and reflash it
@craiggibson90683 ай бұрын
StezStix Fix? How do I contact you to sort out sending you something to fix for me if you can?
@louisvillaescusa2 ай бұрын
Someone at the company told me that these were s special deal with WalMart that didn't sell well, so they started liquidating them on the cheap.
@game_master_rukia3 ай бұрын
try heating up the blob chip cause it could be as simple as a bad connection
@umbrellacorp.2 ай бұрын
I wonder if it's StezStix Rapping. Cause that would be cool.😎👍💯 Too bad it's Extinct. Life couldn't find a way with this one. I wanted to see it work as well. 😩
@chrismcgraw3399Ай бұрын
reflowing the flash chip may have done the trick . it may not do anything if it cannot read that chip for some reason
@boredfartless42212 ай бұрын
How did you know what capacitor value to use when the original had no markings?
@MizuhoChan3 ай бұрын
Alas, in this case, life (you) didn't find a way :(
@victor580103 ай бұрын
Send it to Vince,he loves a challenge. He repaired tiny bond wires inside a watch!
@j.f.christ84213 ай бұрын
That's child's play compared to the wires under that epoxy. And solder doesn't work, you need a micro-welder.
@fouadmida22303 ай бұрын
to me it looks like the screen in the back not the blob chip. try resolder it.
@WidodoWidodo-bh7qv3 ай бұрын
aku suka nonton channel ini karena aku suka ayah ganteng
@Penfold83 ай бұрын
I thought you could heat up the black epoxy and then lift up that goo while it was playable?
@totallyuselessvideoz3 ай бұрын
In another video that presents this, he powers up the tv thought the remote control. Not from buttons.
@eak1253 ай бұрын
Cotton bud with some acetone to see if the blob is soluble in acetone. If so, you might be able to get past the potting material.
@j.f.christ84213 ай бұрын
It's resin. Your main choices are brute force or nitric acid.
@johncooke96553 ай бұрын
What have you got to lose ? Not working anyway what’s the worse it still doesn’t work?
@njm1971nyc2 ай бұрын
I think you mean *high* ESR!
@Awayze3 ай бұрын
We want to see you ruin the blob chip and try and replace the chip underneath.
@heyayay2 ай бұрын
Use the screen and case for a RP Pico and make your own tiny TV.
@phester283 ай бұрын
could it also be a bad ribbon and you are pressing through from the blob chip
@j7ndominica0513 ай бұрын
I liked the rapping clip. But this is a pointless toy product
@shadanzar3 ай бұрын
Am I the only one to notice 18 Volts on the multimeter for absolutly no reason ?
@beavis63632 ай бұрын
Yike orangeman, you just set off my ptsd.
@arghjayem3 ай бұрын
Anyone else watching this thinking we’ve missed a trick here. What if instead of going from video to DVD, DVD to Blu-ray and now Blu-ray to streaming service where nothing is ever available…what if we went a different way with digital route. Instead of downloading a film and streaming via a cable to a TV or through an internet enabled TV….what if digital films came loaded on there own memory chip, a memory chip that also has a tiny lcd screen and either a WiFi card or HDMI hook up. So you have multiple ways of playing a film- either watching it directly on the chip or you connect it to your TV via cable or WiFi and watch it that way? Bring back the physical medium to digital entertainment? 😂 I mean that’s what I thought when I saw this thing. You make it say credit card sized but the thickness of a phone (gotta squeeze a battery in there!). Sure you can download stuff to your phone but it’s not the same, plus at any moment the Apple/Amazon/Netflix could remove it from there servers for whatever reason and it’s gone, or you have to pay another fee to watch it again! Just a thought. I mean streaming, Spotify and everything are cool but I still listen to most of my music on my old minidisc player! Physical media, just feels better, feels like you own what you’re listening/watching 🤷
@j.f.christ84213 ай бұрын
That happened with music. You had HitClips that needed a player, but there were stand-alone things as well. I'm sure TechMoan has covered them. VideoNow was the video version. I have seen magazines where they put an entire video player (screen, battery etc) just to play an advert. Possible with e-ink, we've basically got those as supermarket price labels.
@CallousCoder3 ай бұрын
What you could do is chuck it in a toaster oven at 185C and see if the glob top underneath will reflow.
@truevulgarian3 ай бұрын
Did you just rhyme 4 with four? Tsk tsk.
@rj78553 ай бұрын
"reflow" the blob chip (heat it with your hit air gun)
@danw37353 ай бұрын
Life will find a way to skip to 3:30 lmao. As if we would do that..
@JeffreyGroves3 ай бұрын
How about an ill-informed attempt to reflow the blob chip without removing the blob?
@StezStixFix3 ай бұрын
Yeah, I could do that i guess, but having put heat in one before, it just sort of burns the blob and not much else. Worth a go though, as this is dead as it is!
@alanbutler4873 ай бұрын
Do it, do it, do it 😅
@JeffreyGroves3 ай бұрын
@@StezStixFix I was thinking apply pressure to the blob side while applying heat to the non-blob side... Just a guess..
@jeroenkanis94293 ай бұрын
@@JeffreyGroves that's what I thought.
@mikepanchaud13 ай бұрын
Run a soldering iron over the display connectors. I fixed a calculator like that once.
@mikemike-d2l2 ай бұрын
this was waste of time to be honest. Its worth less than $25 dallars
@Pandor253 ай бұрын
Can you reflow through blob chip?
@AlessandroCussino3 ай бұрын
4:55 That is the contact switch for the "demo mode". When you remove the plastic tab and the contact closes the device operates normally.
@omarroblesgarcia2 ай бұрын
If anyone interested in buying these tiny TVs they are located at Any (Targets) or (Walmarts) or ( Big 5) or (Dollar tree) or ( 99 cent store) the range from $20 to $25 plus taxes like $2 thank me later you guys have a good night or morning I don't know what country you're in I'm in Phoenix Arizona but but good night its currently 12:06am
@GarryL2773 ай бұрын
Just wanted to say thank after watching a lot of your videos I had ago at fixing a broken security camera I had and was able to get it working so again thanks.😊
@davidca963 ай бұрын
The wires are so thin on those chips under those blobs
@juanmena36483 ай бұрын
That MK-something chip might be a Flash Memory, so it's very possible that chip might be corrupt, thus failing to boot. It may need a complete reflash either for Firmware or BIOS (if applicable) so try to get another one and change that integrated. I don't think the blob-chip might be faulty, because, it's getting energy throughout the entire board, and most importantly, the screen boots but can't. Either way, blob-chips are very difficult to replace as most are microchips and not the usual integrated size you'd find regularly.
@andymouse3 ай бұрын
What was the other chip on there please ?....cheers.
@Infinitygaming6702 ай бұрын
They should sell it with the complete movie it would make cool collectibles
@chrisrobson85403 ай бұрын
cant fix 'em all ! even with dave helping lol
@Zhixalom3 ай бұрын
Can a blob-chip be re-seated?!? - You know, just by heating it up for a bit? - from beneath maybe? - aaah yes, the infamous melting counter... that horrible kid next door to Woody and Buzz in Toy Story springs to mind. You know, that brat with the braces who's always torturing his toys. 🥸😆
@309electronics53 ай бұрын
Nope. The blob is a raw semiconductor dice glued and bonded using gold wire to the board and it does not use solder
@Zhixalom3 ай бұрын
@@309electronics5 Maaan, this "no way to repair" mentality sucks... Thanks 👍
@matthewbaker16212 ай бұрын
U have to use the remote control for it to work duh
@robtasker51673 ай бұрын
What donyou charge steave ??. Got some small bits if your interested, 1 is unusual 😮!!??
@eltelboy84923 ай бұрын
Great content as always, I have a SNES that I’ve just brought with a few games, I don’t think it’s working 100% the games don’t look very sharp and some of the colours look a bit dull, so you take things in to repair and return?
@rimmersbryggeri3 ай бұрын
the power for the backlight is aparently getting to the screen but the video signal isnt. Could it be the connection between the screen and the board that is faulty/ intemittent. You really need an oscilloscope fpr jobs like these. Then you could have seen if there was activity on the significant pins of the memory chip for example.