Stihl 038 magnum, I'm getting this clutch off no matter what!!!!

Stuck clutch reveal on a 038 magnum.
pto side crankseal removal made easy.
thanks for watching.

[@brendanthebattlerstafford5145]

Found a bearing with the smallest amount of play on an 046 today and the cage had deteriorated. A couple of hours later I watched your vid and had a chuckle. Spot on Tinman 👊

[@rons3736]

Mechanical Engineer Proverb: The solution is finding the right size hammer to hit it with. In your case, an air "hammer" Keep up the great content!

[@brendanthebattlerstafford5145]

Thank god! Didn’t realise I suffered from OCD until you fixed that dog. I hope I can sleep properly again…😁

[@bobbrant7847]

You do real good work I like the way how you show how you fix the problem things no body else does that. What I like was how you got that stuck clutch off that 038 Stihl.

[@bryanb5413]

The clutch removal cliffhanger form the last episode kept me up last night... Here's to a better night sleep tonight... CHEERS. Many thanks!

[@stevetheriault4164]

IVE PUT THE SAW DOG IN THE VICE TO HOLD THE SAW IN PLACE , AND GRABBED A 1/2 inch 2 foot breaker bar WITH 3/4 socket works good ,always removes stihl clutches for me,for the crank seal so it doesnt prolapse the lip ,you can cut metal from a pop can ,and roll the metal like a cigar ,so it will slide over the crankshaft end for the shim ,then slide your seal down works good,great job TINMAN

[@troy3052]

That's a great tip!!!

[@mikeremski2102]

Nice hearing the house is coming back together. As for new vehicles: you're going to wind up with whatever is actually in stock.

[@tinmanssaws]

That sums up the car market right now for sure!!

[@jordanwickizer575]

i had a stihl come in today with a bad oil pump. i was at my whits end with the clutch not coming off. i will definitely try this!

[@justinweaver8787]

Glad u makin baby progress!!!!

[@oceanheadted]

Ooh I had the socket dish problem that weekend, thanks for the tip

[@justinp7687]

Bought the Stihl tools a few years ago several different sizes but makes it much easier.

[@tdawg8605]

Good stuff as always. Glad to see the house is coming along. TC Tinman Mahalo🤙🤙🤙

[@joutdoorsmen23]

Thanks Tinman, for all your knowledge and info really appreciate and continue prayers for you and your family!!!!!!!!!!

[@sandsock]

We have just started seeing trucks for sale in several yards. It's almost time to buy

[@lyndonwortley6329]

Strongly recommend Stihl seals on these saws. Tried a couple of aftermarket clutches as Stihl clutches are getting hard to come by. Rejected the aftermarket clutches in favour of getting new clutch springs and clutch shoes using the original clutch carriers. Thinking that you won't have the option of reusing the clutch carrier....

[@johnarnettsways.8758]

Nice fix tinman. I will remember that one. Appreciate it ❤️🌲🪓👊🏻🙏

[@jackjamison3816]

Honda crv👌 can't go wrong

[@jeffreyrubish347]

We have a 2008 and it's been trouble free.

[@brianbutcher8216]

Do yourself a favor buy a dewalt 1/2 inch battery impact and just leave a spark plug in it and it brings them right off and they are handy as hell for changing tires or anything

[@larrywarner9314]

Tinman is replace those springs on that clutch to be safe , they loose there strength after getting hot like that

[@imperfectcuts7028]

Love the content as always tinman. Can't wait for the next portion

[@justinweaver8787]

Gonna be awesome saw!!!!

[@tc3603]

You would have made a great teacher tinman💪

[@Joe2328]

I have a 3 foot length of scaffolding pole that I slip over the end of the socket wrench - leverage wins every time!

[@szaboendre9368]

Good call! Turn the saw upsidedown!

[@timothybyrom5560]

Also my wife has a RAV 4. I really like it.

[@BRKS-fj2jt]

IV got an electric heat gun gets them red hot with out the worries of a flame

[@clayton8465]

Lots of friends.

[@69kaveman]

I did not see you put a spring back under the seal, did I miss that ?

[@aaronpowell4885]

To me, that saw is just new enough and has just enough "patina" and battle rash to be a good toss er round, git-er-done work saw!

[@joehackett9471]

bout time ya flipped that dog over!😆😆😆😆😆great video's Tinman!

[@jamesgoss7367]

use a 50/50 mix of acetone & atf oil it works great

[@johnmorris1637]

Wish I could send you a picture of how I cut my socket. Cut it so it has 3 fingers that goes into the clutch.

[@darrenpickens7147]

You install the seal with out grease or oil?

[@74willy81]

One reason the impact did not work is that without a solid stop and hit an impact wrench is largely ineffective. An impact wrench works by using solid mechanical blows. The rope in the cylinder acts like a cushion softening each blow like a pillow. Driving a press fit pin into a hole always works much better when backed up by something solid and hardly at all when placed onto something soft and spongy. Same principle here. I like the rope in the cylinder for most work but when you need a solid stop as in this case, I use one

[@ericbuchta9765]

How’s it going Tinman, Heard about Your channel from Buchin Billy Ray. I’m a nut for a good chainsaw. I am restoring my dads ms-390 he passed away 2019 Veterans Day he loved this saw. I wanted to tell you that the cleaner I started using goof off it’s cheep and cuts grease ya got to try it. Ok will talk to ya 👍👍

[@leonardobatistarocha7956]

The Lumberjack Jackyl Composition: Jesse James Dupree Ha haaa I was born in the backwoods Of a two-bit nowhere town Fathered up some rock 'n' roll (baby) So your mothers could boogie down I ain't whistling Dixie No I'm a rebel with a groove All around the world the go 'round and 'round When they dig on my new stainless steel sound oh yeah I'm said a lumberjack baby And I'm gonna cut you down to size I'm a lumberjack now baby And you're the one you're the one that gets my prize When you hear my motor running You know I surely be coppin' a rise Oh! So I'm gonna crank it up down the alley and jack it Woo I'm a lumberjack now baby I'm a lumberjack now baby I'm a lumberjack now baby Ohh I'm a lumberjack now baby But I ain't jacked my lumber baby Since my chainsaw you (Oh yeah) Ha haaa Whether you like it or whether you don't woo That's the way we like it

[@dwizzleusa4202]

Tinman, got a ms250 any pointers on porting? Or even worth it?

[@justinp7687]

250 timing number are fairly hot out of box alot of work to tear down. Muffle mod it and retune carb if you still want more. Gonna need to move up in saw size.

[@CanadianMapleleaf]

I recommend a Chevy suburban with a two stroke great on fuel 🤣😊

[@troy3052]

Hi tinman

[@tylerheard1279]

I'd pick up a Honda Crosstour, Toyota Venza, or even a highlander.

[@timothybyrom5560]

That would be some of my picks.

[@eurokid83]

Find you a nice third gen 4Runner. You’ll have it for the rest of your life if you take care of it.

[@famasmaster2000]

Tinman, hello

[@kevinmulherin5932]

Buy a 1000 W handheld induction heater

[@jeffreyrubish347]

Gravity. Who knew? 🙂

[@codyroger9581]

Thanks for flipping that dog… lol

[@ryanarthur3641]

Tinman port my xl922!!!!!

[@airport4173]

PROBABLY trying ANTI-CLOCKWISE by mistake.

[@shaneshow6484]

Get a Subaru forester..4cly 35mpg.

[@robertsmith7580]

First you don't succeed get a bigger hammer !