* Stihl ts 420 410 carburetor fuel line filter tune up

check out my hot girlfriends etsy shop www.etsy.com/shop/Sprunket tool
amzn.to/2ECanYT
carb filter fuel line primmer ball
amzn.to/316mwg2
tune up kit
amzn.to/3jWvZzn
todays t-shirt brought to you by YOUR NAME HERE
amzn.to/3ffVfgz
if this video helped you donate a buck or two to my GoFundMe account
www.gofundme.com/f/help-me-bu...
The small engine guys are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com.
primer ball,run,start,cut off saw,concrete saw,rebarb saw,chop saw,repair,replace,stihl,best concrete saw,best cut off saw,repair project,repairing,repair course,how to,fix,fix it,easy,cheap fix,cheap repair,best fix,best repair

[@Abeuss]

Thanks, the company’s 420 started acting up this morning. I hopped on Amazon and picked up a carb kit with the filters, lines, plug and all for $25. I’ll be glad when it is fixed but not looking forward to removing a bit of a slab that wasn’t poured right.

[@smallengineguys]

you got this

[@Tom-ic3jo]

Hi mate, just wanna say thanks for the video! i work in a small tool hire company and stihl saw are always going wrong! quite often they require more than just this but followed this today and got one working again!

[@smallengineguys]

Nice! Glad it helped

[@anthonyhardman9121]

My stihl ts410 is bouncing before i start to cut anything, do you have an idea of what this could be? Cheers.

[@dwinecotton9418]

I Dwine Cotton bought this cut off saw to use as scrapping and found it to be my first but the Best. . But as of September the 1st it started dieing on me ? The first of 2yeara i has been working it. I want to know why it dies after warming up? Chocking its self out as it dies. Thanks for your answers.

[@smallengineguys]

could be many things. the first thing i would do is check the spark when it dies sometimes the coil goes bad but only acts up when it gets hot. sometimes the sparkplug does the same so change it. check the compression if it and the spark are fine its fuel. make sure you are useing fresh bought today gas. all else fails do the carb like in the video.

[@Neckdeepinmud]

Excellent and to the point video. I have a 420 that starts and runs okay, but it lacks power when cutting paving blocks. Any idea what's wrong? Thank you.

[@smallengineguys]

there are 2 adjustment screws together on the carb. the one closest to the air filter counterclockwise a quarter turn

[@ChartoonShow]

I bought ts410 but wont prime just pressurizing fuel tank but when i take off the primer it works when i put fuel in the cap it sucks it up and pushes it out swapped lines on primer holds fuel but doesnt push it to carb any ideas? Thanks

[@smallengineguys]

bad carb. needle valve sounds like its stuck closed or bad diaphragm. could be pinched or kinked line or clogged fuel filter as well. tank will pressurize on its own from the gasoline evaporating.

[@eustaciosaucedo4682]

Thank you

[@smallengineguys]

You're welcome

[@anthonyhunt6765]

Hi Iv just replaced all filters carb and lines but it will only purge the fuel if I tip the saw on the side so the return is in the fuel , any ideas? Thanks

[@smallengineguys]

lines are backwards

[@antonl8346]

Do you have any video of how to assemble the trigger switch and kill switch orange lever assembly .i have a problem with that flat piece with bends on the ends i just fell out when i was taking the carb off

[@smallengineguys]

pretty sure i do youll have to look though sorry

[@mehmetnuribayram0434]

Danke für die Videos, die ich gedreht habe. Können Sie mir auch sagen, wie man den Vergaser einstellt?🎉

[@jlewis572]

Thank you. You have helped me out so much. Do you have a video of complete teardown of the ts420? I need to rebuild the top end

[@smallengineguys]

Not yet sorry.

[@Trivia_Expres]

hello can you help me remove the carb from a 420 saw and I don't know how the ways are connected

[@smallengineguys]

This is a video on a stihl ts 420. Do you have a different model?

[@joaquincortada1483]

Did you watch the video?

[@smallengineguys]

@@joaquincortada1483 2 min 50 seconds showes the 3 bolts holding the carb in

[@smallengineguys]

My bad your responding to this guy my bad

[@joaquincortada1483]

@@smallengineguys 👍

[@phillipgiardino8719]

I have Stijl 420 new primer bulb fuel lines and new carb I won’t prime no matter what I do help

[@smallengineguys]

lines are probably backwards. happens all the time.

[@smithy2k13]

do u have a vid on this saw bogging down please mine doing it naw and dont no wats rong

[@smallengineguys]

Turn low adjustment screw counter clockwise 1/4 turn.

[@hazardpascal5700]

En français

[@A.AofSpades]

Your the man dude! Fixed this fucker on site 🍻

[@smallengineguys]

glad i could help

[@gwynforddafydd1397]

Pity you did'nt show us you starting it up or did it not start ? , i find real life is never as simple as people show in videos.

[@smallengineguys]

It ran. I do this for a living. Its how i make my money.

[@anthonyhunt6765]

Hi Iv just replaced all filters carb and lines but it will only purge the fuel if I tip the saw on the side so the return is in the fuel , any ideas? Thanks

[@smallengineguys]

Lines are backwards