Press the top two buttons at the same time and then power the inverter. This will take you back to the menu to set the type
@flyingtools9 ай бұрын
Thanks for the information 😃👍🏻
@MotoRiff772 жыл бұрын
What was your display doing from the start because mine just blinks on and off
@flyingtools2 жыл бұрын
Hi. Mine was completely black.
@enzo_iw7dmh Жыл бұрын
Hello friend, thank you very much for sharing this video. I am wondering if you can find time for a short feedback video about the Sun GTIL 2000. What about fans noise and standby self-consumption? It would be very interesting at all Best regards Enzo
@flyingtools Жыл бұрын
Hi. I am not using it any more, but I remember the fan nois, it was pretty loud when the inverter was working hard. The stand by power was low, if I remember right 7-10W Thanks for your question, hope this helps.
@enzo_iw7dmh Жыл бұрын
@@flyingtools It helps a lot! Thank you very much 👍
@Tubeophiliac2 жыл бұрын
WAL setting is for wind turbine version. W = wind. Maybe can reset or maybe not significant.
@flyingtools2 жыл бұрын
Hi, thanks for the info. I did choose BAT so I think that it will be correct, I am using it together with my 48v battery.
@mihaitaiosub2 жыл бұрын
@@flyingtools Hi,i use 3 same types of this units feed from battery,and should be SUN,not BAT.
@flyingtools2 жыл бұрын
@@mihaitaiosub ok, thank you so much for your information! I will take care of that.
@honeybadger6127 Жыл бұрын
where did you order the replacement display at?
@flyingtools Жыл бұрын
AliExpress
@magvat2 жыл бұрын
Bra du fikk orden på den. Jeg rekomanderer å sette displayet til å slå seg av etter 10 sek. Det vil forlenge levetiden. Tror du kan trykke de to øverste knappene for å komme i setup meny igjen om du må.
@flyingtools2 жыл бұрын
Tack! Testade detta nu men tyvärr gick det inte. Testade flera kombinationer utan resultat. Som tur är verkar den fungera som den ska. Tusen tack för tippset iaf!👍🏻
@mihaitaiosub2 жыл бұрын
@@flyingtools Hi,you should power up the inverter with those two buttons(up buttons) pressed.Release them when the display is light.Now the inverter is on setup menu.You can try whitout any danger,anytime.
@flyingtools2 жыл бұрын
@@mihaitaiosub Wow, thank you so much for that information!
@jozefmitosinka76115 ай бұрын
hi, can you give a link to the replacement screen, thank you
@flyingtools5 ай бұрын
Hi, sorry i do not have it anymore.
@jozefmitosinka76115 ай бұрын
@@flyingtools hi, I wanted to know where you bought the spare panel - link to the seller
@magvat2 жыл бұрын
Check out Der Kanal he has much good stuff about these units
@RowelLigumbres-bg1fw4 ай бұрын
How to go to this setting. I think I'm wrong set my inverter
@flyingtools4 ай бұрын
Hi. I don’t know, some comments here about how to do but I have not tested them.
@dannysantos29282 жыл бұрын
sir can u help me on my GTIL 2000..?the 8 pin ic U3 is burn.i cant read the partcode..
@flyingtools2 жыл бұрын
Hi. If you mean that one on the display pcb the numbers are: DS1302Z 2102A5 069ACN Hope this helps.
@dannysantos29282 жыл бұрын
no sir ic U3 on the main board..driver for the mospet sir..thnk u for your reply..
@flyingtools2 жыл бұрын
Ok, i will take a look at that.
@dannysantos29282 жыл бұрын
thnk u very much sir...
@flyingtools2 жыл бұрын
Ok here are the numbers: HHXAA EAN3224T It was extremely hard to se but I think this is the right numbers.