Super Bass Stereo audio Amplifier using PAM8403 | pam8403 5v amplifier bass

[@boseelectronicstrivandrum8086]

♥️❤️❤️

[@skillmake]

thanks for comment 🙏🙏🙏 .mr??

[@anishlifestyle123]

@@skillmake 🥰🥰🥰😘

[@rajbalachandran9465]

ഇങ്ങനെ connect ചെയ്യാമോ? അടിച്ചുപോകില്ലെ?

[@sausagedog52]

these amps are already 4 ohm stable and youre running 8 of them into approximately a 1 ohm load, so each is probably seeing the equivalent load of an 8 ohm load. also youd get more power running them at their rated 5v instead of 3.7 or under load likely closer to 3v. also assuming they were all making their peak rated power you would be getting less than a typical car audio head unit.

[@blackIce504]

no crossovers on the speakers and those smaller speakers and tweeter would be working very hard getting the full frequency spectrum........Also each amp does not have any protection on its output thus some of the amps will be working harder then the others normally when you see multiple fets or amps you use a resistor to load balance. Oh well it was good for a laugh.

[@thebanditgamer4865]

each 1 of those little amplifier boards dont push out more than 3W at 5V. they are rated for 5W but they dont do more than 3W at 5V

[@shivsaini3562]

मेरा भारत महान। जब तक आप जैसे नागरिक हमारे भारत ने है। कोई चाइना हमसे आगे बेहतर नही हो सकता। 👍

[@skillmake]

नमस्कार प्रिय मित्र, मुझे बहुत खेद है, अमल, मैं ईरान से हूँ, लेकिन मुझे आप जैसे भारत के दोस्त बहुत पसंद हैं 🙏🙏🙏

[@shivsaini3562]

@@skillmake मुझे वह सभी लोग प्रिये है जो सभी की सहायता और एक दुसरे की सहायता करते है बिना किसी स्वार्थ के मुझे किसी भी धर्म, पंथ, मज़हब , रिलीज़न और देश से कोई लगाव नही बस अच्छे और सच्चे लोग मिलने चहिते। ॐ

[@botolbotol9984]

@@shivsaini3562 ngomong apa sih

[@naukapokojuteachpeace7251]

Yo Wanna be indian. Memory of arians is coming backto us....soon end of trials and tribulations. Replacement hoomans time is ending. I was always blown away that as a polish lad i was preaching vedic teachings to wanna be indians who should understandit deeper than me...or do they ? Truth is coming to the surface. What's then. Are you panicking ? Cuz im excited.

[@naukapokojuteachpeace7251]

And that moon landing done in a style of power rangers from 90s 😂

[@dammdaniel9953]

As an audio engineer with 10+ years of experience i can definitely say you dont have any research knowledge on how amplifier and speakers ohms works and matter in audio . I won't say stop doing what you love but learn for your past experience and improve yourself

[@2fathomsdeeper]

Unless some of those drivers are 16 Ohm, those amps have got to be frying! I know one of those drivers was 4 Ohm. 30+ in audio!

[@skillmake]

Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 kzbin.info/door/BoZGn08nBAxE9M5T53_UKg

[@saranaaircond816]

​@@skillmake 8:48

[@electronicshelpcare]

Good Work brother

[@mrdead3189]

پرچم ایرانو بالا بردی با ایده هات حجی❤❤❤🔥👌🤟

[@AntonIntelligent]

Жесть, невероятно, дайте автору премию за гениальность 😁😁😁😁

[@skillmake]

😂😂

[@tank_v_tanke]

Оскар за гениальность... А может 10 оскаров?

[@TheKamarataboba]

А лучше столько Оскаров - сколько Он плат запараллелил. 😁😁😁😁

[@g-forsemanx4664]

@@TheKamarataboba самое интересное что мощность как у одной микрухи по итогу все равно на выходе

[@majorov89]

@@g-forsemanx4664 и далеко не факт, что все усилки заработали, они ведь D класса и на выходе дросселя нет, фиг знает что с генерацией там происходит, уверен, что синхронно они не запускались

[@P43L1j0]

We almost can see the impedance say hello to those speakers... if you going to try this at home, please read about it...it save you a lot of trouble and a bit of money. Btw...you just need one AMP... not 8. Good video tho.

[@utkarshchari7931]

What is the key difference between 1 pam8403 vs 8 stacked pam8403 Does the power is increased sightly?

[@skillmake]

Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 kzbin.info/door/BoZGn08nBAxE9M5T53_UKg

[@ReimuReimu_Animation]

@@utkarshchari7931 It depends on the Supply Power and Impedance of the speaker [ I = V/R ] If your speaker type is 4ohm and your supply voltage is 5v then. [ 5 divided by 4 = 1.25A ] which means [ 5 x 1.25 = 6.25watts ] 1 amp of current 6W runs to the Speaker. Ex 2 If your speaker is 8ohm and your Supply voltage is 24v then. [ 24V / 8ohm = *3A* ] [ 24V x 3A = *72Watts* ] Ex 3 So if you want 1,000Watts 24Volts runs to your Speaker Coil and 4ohms speaker Impedance then. [ Watts / Voltage = Current ] [ 1000w / 24v = *41 Amps* ] Hope this helps to find a suitable speaker and amplifier and also power Supply DC to DC or AC to DC Supply Thanks for reading :)

[@arielbene2013]

@@ReimuReimu_Animation very well explained. .. So is there any point of stacking 8 5v amps over just 1 amp? They all get 5v 1A 4 Ohm anyway

[@ReimuReimu_Animation]

@@arielbene2013 yep it depends on the speaker ohm if it's 1 ohm then it's like a short circuit it will suck more current than 4ohm

[@maykevin5]

8 stacked together and still barely enough to push a 20 watt speaker. Super Powerful!

[@maximilianjuli4895]

i highly doupt that the 8 amps could drive the two 300W speakers. at 5V the current supplied by the batterys would neet to be 120A . even if that were possible it would let those puny wires and speakers go up in flames imeadietly.

[@pvanb291]

Correct! This video is complete BS!! Super powerful my ass! :( I was doing an audio engineering course where the main amps we used were QSC and Crown 2400W RMS bridged into JBL SRX825s. Even that wasn't "super powerful". It's really just industry standard. Those 300W speakers are also bullocks. The way ratings are applied to car audio, you'll find they're around 25W RMS. Good video for comedic value I guess.....

[@skillmake]

Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 kzbin.info/door/BoZGn08nBAxE9M5T53_UKg

[@skillmake]

Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 kzbin.info/door/BoZGn08nBAxE9M5T53_UKg

[@greyparrot5194]

@@maximilianjuli4895 So what do you think this is fake I m going to try it and i thinks a lot about it what if this isn't work Please guide me bro

[@vijaykumar-np8qq]

Great innovation... Keep it up 👍. love you from India 🇮🇳 proudly..

[@skillmake]

Thanks mr Kumar thanks for watching

[@sunuk1915]

Red wire basically use for right channel of audio applications

[@llewellyn56]

that's insane but awesome. great video.

[@jyotirani8232]

Wow, great 🧡🧡

[@skillmake]

Thank you 🤗

[@timextoxicgaming20]

Hi

[@sugengpurnomo692]

Ini yg kucari.. benar2 meningkatkan daya .. bukan pakai modif tone control pasif yg hanya mengurangi/menghilangkan suara midhigh nya .. Kerennn..

[@Алекс-я4х9г]

Я извиняюсь, но это что за херня ?! Паралелить усилки да еще в таком количестве?! А резисторы с плюс питания на входы зачем?! что б помехи по питанию слушать?! Срочно отдать на проверку Доктору)))

[@skillmake]

it just for test 🙏👌

[@Nextway93]

Да это пиздец. Ещё нагромождение спикеров, разной мощности, разного сопротивления, все параллельно. Кажется, чела в школе научили только ПАРРАЛЕЛЯМ. Странно, что он не присоединил несколько входов и к ним несколько телефонов с одной мелодией не запускал параллельно

[@Nextway93]

Хаха ещё этот долбан думает, что там у него выдало почти 50W.Это наверное, какие то параллельные ватты, из параллельного мира

[@deadshotprime9329]

اول فک کردم از این چنلای فیزوریه هندی هستی..😄 دمت گرم دادا اگ شد ت تایتل ویدیو دو سه کلمه فارسی بزار ویوهات برن بالا Nice job👍Keep it up.

[@skillmake]

سلام داداش شما ها از کجا میدونید من ایرانیام واینکه خودم انگلیسی شروع کردم برا ایندش فارسی به درد نمیخوره 🙏🙏❤️

[@DashCamCarCompilation]

دمت گرم داداش باحال بود موفق باشی

[@skillmake]

مرسی داداش

[@gaweown]

Sambil makan sahur hadir dan menyimak menambah ilmu,salam sukses selalu

[@Ayushyadav-rq3bu]

It's not fake it may possible but you need 5 volt 10amps adapter

[@skillmake]

Hello dear friend, yes, you are right, it has a high amperage

[@lovneetsingh6664]

@@skillmake if speaker has 4ohm resistance , then max current will be 1.25 x 2 = 2.5 amp, and current cannot go beyond that. simply its fake

[@Roriloty]

@@lovneetsingh6664 what if he use a lipo battery that can supply a lot of current thought 🤔

[@lovneetsingh6664]

@@Roriloty even if using lipo battery, the max current will be 2.5A. 5V cannot give more than 1.25A per channel. Simple ohms law I = V/R

[@Roriloty]

@@lovneetsingh6664 what if I connect multiple batteries in series would it work? (And thick wire)

[@SenTirTv07]

Keren ... mantap .... kreatifitas tiada batas.... Salam kenal dari Lereng Gunung Slamet saudaraku

[@skillmake]

🙏🙏🙏

[@pathmakumara1279]

Congratulations from the bottom of my heart I do a good job for you

[@pathmakumara1279]

Please help me write down the ICs I need to fix this

[@skillmake]

🙏🙏🙏

[@gagan_jit7897]

This is called real experiment full fun with dis

[@skillmake]

thanks

[@bhartiymudra9987]

This time you dun well solve ing ampere problem 🔥🔥🔥🔥🔥

[@skillmake]

Thanks for comment 🙏🙏🙏🙏

[@vitaliy.af_]

2 таких слабых аккумулятора не подходят для этого, их не хватает. 1 аккумулятор 18650 намного лучше подходит так как он сможет выдать 10 ампер спокойно

[@skillmake]

👌👌

[@fabdab5472]

Kya 8 PAM module 4-4 speakers dono taraf ke liye theek hai. Matlb IC kabhi kharab to nhi hogi volume bhadane se

[@skillmake]

हाँ य़ह सही हैं

[@ReimuReimu_Animation]

I think 1 amplifier is enough It depends on the Supply Power, Impedance of the speaker and also Voltage. [ I = V/R ] If your speaker type is 4ohm and your supply voltage is 5v then. [ 5 divided by 4 = 1.25A ] which means [ 5 x 1.25 = 6.25watts ] 1 amp of current 6W runs to the Speaker. Ex 2 If your speaker is 8ohm and your Supply voltage is 24v then. [ 24V / 8ohm = *3A* ] [ 24V x 3A = *72Watts* ] Ex 3 So if you want 1,000Watts 24Volts runs to your Speaker Coil and 4ohms speaker Impedance then. [ Watts / Voltage = Current ] [ 1000w / 24v = *41 Amps* ] Hope this helps to find a suitable speaker and amplifier and also power Supply DC to DC or AC to DC Supply Hope will help your Calculations and also it Depend on the volume the Amplifier voltage drop because some of energy may not go through the speaker rather to Heat Due to Parasitic Inductance and Resistance of the speaker and Amplifier Components :)

[@BMA_YT]

QQ

[@ReimuReimu_Animation]

Ex 3 is basically Wrong calculation but ex 2 and 1 is obviously correct.

[@ReimuReimu_Animation]

@Black Pepper Usually your correct it depends on the wattage or impedance of the speaker so you can connect this tiny amplifiers in pararel so the components won't heat up and delivers more power depending on your supply power and the output voltage won't collapse :]

[@AmanAman-bg8bl]

@Black Pepper can you give a calculation. Then we can choose the amplifier according to speaker. You can give us 1 or 2 example like he did.

[@AmanAman-bg8bl]

@@ReimuReimu_Animation can you give a calculation. Then we can choose the amplifier according to speaker. You can give us 1 or 2 example like he did.

[@PenguinDIY]

goooood

[@skillmake]

Thanks mr 😘😘

[@mihamihavich6802]

Great work. It was interesting. Now i know what i will do tomorrow))

[@skillmake]

Good luck!

[@lovneetsingh6664]

fake hai bhai...thodi electronics parh k dekhlo pehle

[@bompomofficial2131]

Wow. Great Content. Is the Interesting Tx.

[@skillmake]

Welcome!

[@Ayushyadav-rq3bu]

Maine bhi socha tha ye idea but kbhi try nhi kiya

[@skillmake]

🙏🙏🙏mr ayush yadav

[@NailaBabar-kj9xk]

Tary bas ki bat NAHI TU bas youtub pr videos dekh

[@charanexperiment9]

​@@NailaBabar-kj9xknalayk chup

[@nguyentuan0712]

Làm ×100 đi bạn

[@skillmake]

😮😮😮😂😂

[@darkside7786]

Try X 100 bro . I think very interesting than X 8 👍👍👍 I wait next ur videos X 100

[@skillmake]

@@darkside7786 💪💪💪🙏🙏ok ok mr johan ❤️❤️❤️

[@darkside7786]

@@skillmake i waiting for next X100 bro 👍👍👍💪💪💪

[@mr.soundcraft822]

Very good keep it up and do many videos about audio

[@skillmake]

Hello dear friend, thank you for watching a lot of videos about amplifiers and Bluetooth speakers. I will make a video🙏🙏👌

[@AlzAdz]

Creative👍

[@skillmake]

Thank you 🙂🙏🙏

[@Editsforlife11]

Awesome work. Keep posting this type of videos 👍👍👌

[@skillmake]

Thank you, I will

[@skillmake]

Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 kzbin.info/door/BoZGn08nBAxE9M5T53_UKg

[@xStStSx]

Wow.. why so much fake in this video ? Don't do this , it's totaly fake. 1) PAM8403 doesn't work as PBTL - Parallel Brige topology. 2) PAM8403 output it's square wave, so if you doesn't sync them - it's short circuit. 3) Total impendace of each channel around ~ 1 Ohm. PAM8403 driving minimum 3Ohm. 4) Why you adding push up resistrors at input before capacitors ? It's the right way to burn source outputs. 5) Why to add capacitors ? They are already placed in the module. 6) Twiters and a rest of the speakers without crossovers or other filters.

[@skillmake]

Dear friend, this circuit was only for testing because many people had asked me in the comments🙏🙏

[@xStStSx]

@@skillmake You showing it like a working solution ,but it's not. It's totally misleading solution and wrong. Though not working solution. So it's fake.

[@makoveliprod]

In the video, you can hear how the modules go into protection by short circuit, sometimes even the sound is interrupted. They just run asynchronously one module at a time. The exit time from protection is different, so the sound is continuous, but each module works only for a short period of time. As I understand it.

[@jj74qformerlyjailbreak3]

Sir I appreciate your talent. Thanks for paying it forward by sharing. Also I love channels who interact with the comment section. Your light shines bright even through these digital boxes we find ourselves trapped in from time to time. God Bless.

[@skillmake]

thanks 🙏🙏🙏 mr jailbreak?

[@Beoyur]

He has no talent...

[@erandayohan3845]

Do you hear some noice in the circuit. Because i have this amplifier. But i connected before my phone its hear big noice. How could you achieved that

[@skillmake]

If you want to hear less noise, I recommend using a battery to power the module.🙏🙏

[@Wajeeh-tu1uk]

Bro you can just use only one board instead of 8 bro only the bass is for the capacitor and resistor bro why you wasted your money why but if you use too much that will become more power full and consume more amps however your circuit is good i appreciate it 👍👍

[@nurulilham1901]

Would you mind making pam8610 parallel? I tried them but failed. Thanks.

[@skillmake]

Maybe I will test in the next videos🙏🙏

[@nurulilham1901]

@@skillmake I am waiting for your actions.

[@undead0133]

so, you make 5v 20amp amplifire ? :D

[@josefelipesantos3150]

Eu ligava essa placa. Som grande tocava bem 😂

[@janzmicrotronix5397]

try to use 5V 3A power supply with 470uf filter capacitor instead of parallel 3.7V mobile battery for better bass... in my own opinion 😸😸

[@skillmake]

🙏🙏👌👌

[@trunggiangnguyenfamily8923]

Thank you im from việt nam

[@skillmake]

thanks

[@RandomTv_1223]

Shorting amplifier output with other amplifier. Nice.

[@skillmake]

Yes, thanks

[@탑수리맨]

WOW~! Thanks for the good video~!^)^

[@skillmake]

Thanks for visiting❤️❤️

[@ahyonvlogs]

what value r those rwsistor and filter cap u put on Input leads ?

[@skillmake]

Details of all items are written below the video Dear friend

[@_al-faqir99_21]

mantap 👍👍👍👍

[@niadaniati4208]

😲Amazing 👏👏👏👏👏👍👍👍👍👍

[@skillmake]

Thanks 😄

[@rafafaeyza6316]

Keren bang..kl di pakein 2 sub ngangkat g itu bang pam nya...

[@skillmake]

yes gooood

[@edoprastyo8836]

I tried it, but it doesn't sound. Can you give me a solution please?

[@sadadanwar3505]

That's how many modules 8403 pack...

[@Uraim]

5:22 thats just dump, the idea is maybe good if you wanna get really low impedance on the speaker, not bad idea stacking that amplifier, but still, you need thirty piece of this board to do something with 1 speaker. It just not worth. The recommended impedance is 4-8ohm buddy, due the amplifier runs on low voltage the amplifier probably not gonna explode but it still, looks horrible, the stacked amplifier looks dope ngl

[@skillmake]

thanks for comment mr robi🙏🙏

[@Uraim]

@@skillmake try Make a dream tower out of these amplifiers, the input will be Bad of you will connect all the inputs in parallel,so you have to get like 25-30 of these boards and some op amps to drive the inputs correctly, you will get a really nice amount of power like 75-90W/channel

[@akshoy1867]

Bhai isko bluetooth module ke sath jor kar ek video baanaiye na

[@skillmake]

ok mr ashoy be Shure 🙏🙏

[@akshoy1867]

@@skillmake thanks sir Kripiya jaldi baanaiye Hume besabri se intezaar hai

[@yagneshpatel1183]

It work give 24 watt per channel but also impedance became 32 ohms so use for tweeters 16 ohms in series . You just parellel amp but also you need some balance resistor for futher protaction to balance gain

[@skillmake]

Thanks for your help, this video was for testing

[@karimabrokhafan6942]

عالی داوش🇮🇷🇮🇷

[@cuf_]

Just use a transistor or mosfet to amplify signal of 1 board it would be million times smaller and more efficient

[@skillmake]

gooood ❤️🙏

[@utsavsarkar604]

I have 1x8ohm , 2x4ohm speaker how many pam 8403 do I need and how much power supply does it need ?

[@mdi-vo7oc]

Best of the best

[@skillmake]

thanks

[@Stargaming94443]

Are ek bada wala chalake dikhao us amplifier se ❤❤❤

[@tonysrepair198]

verry good i copy that thankyou

[@skillmake]

thanks for comment 🙏☺️

[@low-key-gamer6117]

When you have zero knowledge in basic circuit design.

[@skillmake]

😂😂its just for test

[@urnoob5528]

@@skillmake laugh at urself for being a clown

[@Sahel_prince]

Your knowledge is zero...... just experiment 🧪

[@XenyQ_OFF]

​@@urnoob5528it's an experiment .

[@askagamer8339]

If I would be him I would try it to if you don't now something try it yourself

[@Grenade80]

All speakers in parallel? What a parade of madness...

[@skillmake]

it's just for test 🙏

[@djdizzel1]

Надо было ещё насрать в дифузоры. Такая дичь. Сколько ом нагрузка получилось - побоку. Фильтра для вч звена - побоку. Да и мощность там получилась около 5 ватт, поэтому пищалка и не сгорела...

[@skillmake]

🧐🧐🧐

[@eviltechyt3962]

Bro im using 3 pam 8043 amplifiers combined with mp3 bluetooth module and im using these amplifier with 25w speakers in pairs for one pam board but when heavy bass comes the voltage drops so can you 3 me a powerfull power supply to the boards.

[@andre.mendes]

use um capacitor na entrada de energia da pam8403

[@ourchannel8215]

Many parallel speaker can get short circuit...try used just max 2ohm...

[@skillmake]

hi mr ary yt thanks for comment 🙏🙏

[@NoeDohc]

Coba bikin yang tp3116d2 di susun 3 lantai bang?🙏

[@Astral7xFT]

can you connect everything in the same way, but with only 1 amplifier? I wonder how much the result will be different

[@skillmake]

You can test it

[@Astral7xFT]

@@skillmake No, i don't can)

[@lukaszeilinger1353]

1 amp will not be able to handle a load with is below 1ohm.

[@utkarshchari7931]

Yeah please do 1 vs 8 pam8403

[@JaviersDIY]

Nice one sir

[@luckymono]

nice job...how about another PAM's module?, have you got experience too?

[@skillmake]

I think it is the same in other modules👌👌

[@chrisredfield5278]

why did you connect two inputs to 5v pin with caps and resistors. ?

[@skillmake]

for increased input power

[@chrisredfield5278]

@@skillmake Thank you..

[@skillmake]

@@chrisredfield5278 ❤️❤️

[@Sansara9696]

Идея нормальная, но у меня вопрос зачем на входе резисторы и кондинцаторы?

[@AmanAman-bg8bl]

Genious I need a help, I choose speakers which is, 1 subwoofer 4ohm 25 watt and 2 full-range 4ohm 15w. So how many of pam8403 I need to perallale? I want to know the calculation for my understanding.

[@_tanveer__111]

Bro why you use capacitor in the circuit?

[@boombok2diy31]

ใช้เป็นแอมป์โมโน100วัตต์หน่อยครับ

[@skillmake]

ok mr phonkrit 🙏 thanks for comment

[@Wonoketingal]

wow cool

[@skillmake]

thanks 👍

[@Bhilortok]

How many volts for the Elcho/capacitor?

[@gagan_jit7897]

Make video on pam8610 amp board (use 6 board of pam8610) plzz requested man and do this same experiment

[@skillmake]

okkkkk🙏🙏

[@madax7540]

Ya konsi tar hai jisse apna audio bord connect kara hai

[@ruhinmasruhin5076]

R220k connected to vcc? Explain please

[@alimughal663]

only 2 mobile battery done this whole setup???

[@rafaelvenzal8772]

Great idea!

[@skillmake]

Glad you think so!

[@makingelectronicsshorts5243]

Nice Experiment Bro

[@skillmake]

Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 kzbin.info/door/BoZGn08nBAxE9M5T53_UKg

[@noumanumar7305]

Can we use less than 8? Say like 3,4,5?

[@KuntalGhosh]

U know the channel is full of shit when a "free energy genrator" tag comes up on the corner 🤣

[@skillmake]

kzbin.info/www/bejne/fXq0dJ6Qn7Onr9k Hello dear friend, please be sure to watch this video to understand the case. I made this video just to inform you. 🙏🙏🙏 thanks please watch video from links 🙏🙏

[@ahyonvlogs]

wont the ics get hot easily on that setup?

[@skillmake]

no dont get more hot me ahyon🙏🙏🙏

[@greyparrot5194]

Sir i have a question I got an amplifier of 15W+15W output and connect 5W speakers on it but when i open volume my speakers start cracking why May i have to connect 15W speakers on it?

[@skillmake]

Use a higher powered speaker and control the input

[@vempatapumanikanta4737]

Bro can i use Two 8ohm 10w speakers and two 3w speakers and one 45W speaker with Three PAM8403 ?????

[@los___santos]

İs this possible for pam8610 ?

[@skillmake]

Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 kzbin.info/door/BoZGn08nBAxE9M5T53_UKg

[@gabrieltrujillo6627]

If you measure the total impedance it will give a ridiculously low value that explains why they move so much with the music.

[@skillmake]

👍👍👍

[@Manjitsingh-bs7or]

When i have 5 board then which value of capacitor and resistance i connect?

[@testone1150]

Dude thats cool but i think u need more power try that with lithum battery get like 12v with more than 30000mah try it and show us

[@azzalleaazzallea6218]

noooo otherwise It explode

[@testone1150]

@@azzalleaazzallea6218 no bro he just used 8x from that module each 1 = 5v so 5v * 8 = 40v but! I say he try only 12v with high Amps

[@skillmake]

👌👌

[@urnoob5528]

@@testone1150 tats not how parallel works, bro it s elementary or highschool science

[@donMcDice]

I want to diy multi connection splitter for audio signal.Sir can i use caps,resistor plus 5v supply.just like what you did sir.

[@ricardocano3439]

porque no hiciste la prueba con parlantes en caja acustica

[@djnoisechile]

a eso se le llama conexion modo bridge ?? esto incrementa la potencia manteniendo el voltage pero aumentando el consumo en miliamper, ciero ?

[@Bhilortok]

How many volts for the Elcho/capacitor?

[@Simply_shiva_s]

When i connect battery on this no sound all modules heated 🤦 hope no modules get damaged cuz i disconnected the battery 😌

[@dfn03]

Just about 5W is the maximum output since the voltage doesn't get any higher. 5 volts divided by 4 ohm speaker is just a bit over 1 amps. 5 times 1 is 5(Watts). RMS power is even lower!

[@skillmake]

it's only for test

[@dfn03]

@@skillmake But you are telling to people that each additional amplifier adds to the overall output power, which is NOT true and is misleading!! I've been reading your comments... Not very honest

[@chant2012]

you are right, its misleading, i used two modules in parllel and I did not get any extra power@@dfn03

[@dima_maltes6749]

Привіт! А які ще можна уселителі так підключати??

[@dima_maltes6749]

Наприклад PAM 8610 або TPA3110

[@sultanmulyono4781]

Klo dipakai utk subwofer bisa.

[@molun6204]

Each module has only 3W, and 8 PAM8403 modules are superimposed and connected in parallel. How much W is this driven?

[@skillmake]

hi mr yan jun around 24+24watt

[@molun6204]

@@skillmake Thanks for sharing

[@sleepy9817]

Huh 3.7v =24w, hardly 5w maybe

[@mirzaalihassan4129]

@@skillmake are u made All boards become dead if we use in parallel or series

[@mirzaalihassan4129]

@@sleepy9817 no waats it become dead

[@BahramDolati]

First of I think Red wire was right and white wire is left. The other problem is different impedance of those speakers will definitely create distortion. Also you are running 8 Amp boards with the input signal of one AUX output, which in many cases is not enough to deliver a decent signal to each board. So you wouldn't have access to a lot of power output because input is weak and seems there would some impedance matching issues in input. Also running that setup with 3.7 volt is silly because you can't use all power of amps. So for this to work well, you need a pre-amp to properly feed all boards (maybe few pre-amps). Also you need a boost converter to turn that 3.7V into 5V. Also how you're gonna charge those batteries? maybe you need a circuit to boost voltage and also charge the batteries.